FEIT Electric SPOT/PANEL/SYNC High Output LED Solar Spotlight User Guide

FEIT Electric SPOT/PANEL/SYNC High Output LED Solar Spotlight

We appreciate the trust and confidence you have placed in Feit Electric through the purchase of this High Output LED Solar Spotlight. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available tor your home improvement needs. Thank you tor choosing Feit Electric.

Safety Information

READ BEFORE INSTALLATION AND SAVE THESE INSTRUCTIONS

CAUTION:
Contains one 18650 rechargeable lithium-Ion battery. Risk of fire, explosion, or burns. Do not disassemble. Do not crush or damage the battery. Do not heat or incinerate. Do not open or disassemble. Do not make modifications to this product.

WARNING:
Dispose of used battery promptly according to local recycling or waste regulations. Keep battery out of reach of children and its original package until ready to use. Clean battery contacts and unit contacts prior to installing new battery. Ensure that the battery is installed correctly with regard to polarity(+ and-).

HOW SOLAR LIGHTS WORK:
Solar panels convert sunlight into electricity. During the day, while the sun is shinning, electricity converted by the solar panel is stored in the rechargeable battery. At night, the solar light is powered by the battery using the electricity stored during the day. The operating time depends on geographical location, daily weather conditions and season.

CHOOSING THE RIGHT LOCATION:
It is important to select a location with as much sunlight as possible. Shady areas will not allow the battery to be fully charged and will reduce the nighttime working hours. Be sure that the selected location is not close to other nighttime light sources such as streetlights or porch lights. These light sources may keep the solar lights from turning on automatically.

DUSK TO DAWN OPERATION:
This product is designed to only operate at night. The light will remain off during the day and tum on automatically at dusk and remain on for up to six hours.

NOTE: To make sure this function works properly, the switch must be in the selected color position.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radionv technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. RF Exposure. The equipment has been evaluated to meet general RF exposure requirement. The device can be used in portable condition without restriction.

Supplier’s Declaration of Conformity: 47 CFR § 2.1077 Compliance Information

Responsible Party:
Feit Electric Company 4901 Gregg Road, Pico Rivera, CA 90660, USA

Unique Identifier:
SPOT/PANEUSYNC (L)

Limited Warranty

This product is warrantied to be free from defects in workmanship and materials for up to 2 years from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, visit feit.com/contact- us or call 1-866-326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

Pre-Installation

TOOLS REQUIRED

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

1

DD

EE

| Solar panel ground stake

Screws

| 1

2

FF| Wall anchor| 2
GG| 10 ft. cord| 1

Pre-Charge

For best performance, charge the unit for two (2) days prior to use

• Remove the insulating tab.
  E In order to properly charge, the unit must be turned OFF. Use the On/Off/Cycle button to cycle through all of the colors (Soft White, Bright White, Cool White, Daylight, Deluxe Daylight, Red, Blue, Green, Yellow, Orange, Purple, Teal, and Pink) and reach the OFF position.

• Select a location with as much sunlight as possible.

• After the unit has charged in the sun for two (2) days, turn it back on by pressing the On/Off/Cycle button and selecting the color of your choice. If there is daylight outside, it will stay on for about 1 O – 20 seconds and then turn off. If it is nighttime, the unit will remain on.

Installation

Solar Spotlight Installation

Peel off the sticker from the solar panel and remove the insulating tab

• Peel off the sticker from the solar panel.
• Remove the insulating tab.
• It is recommended that you charge the unit for two (2) days before use to adequately charge the battery, following the Pre-Charge instructions.

Installing the stake
Push the spotlight ground stake (BB) into the ground. Using a rubber mallet, insert a spotlight ground stake (BB) deep enough into the ground to ensure fully assembled spotlight (AA) is stable and does not tip over.

IMPORTANT:
Do not push on the spotlight (AA) or you may damage the unit.

NOTE:
When installing product in hard or dry U soil, water the soil several hours beforehand to make the installation easier. You can also break up the ground lightly with a stake or a fork. Don’t force stake into the ground as excess force can break or bend the stake.

Installing the spotlight

• Slide the cables coming from the spotlight through the opening on the side of the spotlight ground stake (BB).
• Align the spotlight ground stake (BB) with the locking mechanism on the inside of the spotlight (AA).
• Slide the spotlight (AA) downward until it sits squarely on the stake.
• Rotate the spotlight (AA) clockwise to lock in.

Solar Panel Ground Stake Installation

Installing the solar panel ground stake

1. Select a location with full direct sunlight and push the solar panel ground stake (DD) deep enough into the ground to ensure that fully assembled solar panel will be stable and will not tip over.

Installing the solar panel

• Screw the solar panel (CC) onto the solar panel ground stake (DD) by rotating it clockwise.

IMPORTANT:
Do not push on the solar panel (CC) or you may damage the unit.

NOTE:
Adjust the solar panel manually, to a position best suited for maximum direct sunlight.

Solar Panel Installation on Roof or Fence

Installing the solar panel on a roof

• Place Solar panel (CC) on roof or fence. Mark the holes using a pencil.
• Drill through the marking and insert the anchors (FF).

Attaching the solar panel

• Insert provided screw (2) through the holes) on the solar panel (CC) base.
• Using a Phillips screwdriver, turn the screw clockwise.
• Repeat with another screw on the opposite side.

Operation without Remote

This Onesync spotlight works on its own or with the provided remote. It also can be controlled via WiFi with the smart bridge (sold separately).

DUSK TO DAWN OPERATION:
The unit will automatically turn on at dusk and remain on through the night for 6 hours. The unit will remain off throughout the day, until dusk. NOTE: To make sure this function works properly, always have the switch in the ‘ON’ position (including daytime).

Connecting the Spotlight

• Connect the spotlight (A) to the solar panel (CC) by screwing on the attached extension cable (GG).

Turning on the Spotlight

• Turn the spotlight (AA) on by pressing the button on the back of the unit. The light will turn On and stay On in the nighttime.

Selecting a Color

• To cycle through the colors, push the Cycle button.
• Colors are: Soft White, Bright White, Cool White, Daylight, Deluxe Daylight, Red, Blue, Green, Yellow, Orange, Purple, Teal, and Pink.
• The spotlight (AA) will remember the color setting when next turned on.

IMPORTANT:
Light brightness is determined by the charge level of the batteries. Brightness will decrease during operation to extend battery life.

IMPORTANT:
Selecting a color, other than white, will extend battery life.

Adjusting the Spotlight
To adjust the angle of the spotlight (AA):

• Loosen the thumbscrew on the spotlight counterclockwise.
• Manually lift or lower the spotlight to the desired position.
• Tighten the thumbscrew clockwise to lock in the spotlight angle.

Operation with Remote (sold separately)

Operating with a OneSync remote allows for expanded control. Modify settings of individual OneSync units or multiple units in groups. The OneSync remote has a 100ft control range and will command all paired units within 100ft of the remote. All OneSync units are equipped with a signal repeater that will repeat any remote commands to all other units within 100ft. Placing units within 100ft of at least one other unit creates a control network and allows for unlimited remote control range, as long as there is a functioning OneSync unit within 100ft to relay the command.

Example:
You can install a OneSync unit, then another OneSync unit 100ft away from the first unit. Continue to install 3 more OneSync units in this way so that the last unit is 500ft away. Using this relay technology, the remote will control the farthest unit which is 500ft away.

1. Entering pairing mode
   • Hold down the pairing button on the unit for 3 seconds. Once the spotlight (AA) starts to blink slowly it is in pairing mode. The spotlight (AA) remains in pairing mode for three minutes until successfully paired or timed out.
2. Pairing the remote to the Spotlight
   • While the spotlight (AA) is in pairing mode, press and hold the desired Groups button (1, 2, 3, 4, 5 or 6) for 3 seconds to pair the remote to the selected group. The light will flash to indicate successful pairing, and the unit will exit pairing mode.
3. Unpairing the Spotlight from the remote
   • To unpair, first follow step 1 so that the unit is in pairing mode. Once the unit is in pairing mode, on the OneSync remote, press the pairing group button and hold the power button for 3 seconds.
   • The light will flash to indicate successful unpairing, and the unit will exit pairing mode.
   • To unpair unit from all groups at once, hold down button on the OneSync unit for 10 seconds. It will flash three times rapidly to indicate that all groups have been unpaired from the unit.

NOTE:
The remote comes equipped with a universal Group #1. To create unique groups, pair using Groups #2-6. U All units are pre-paired to the universal Group #1 so that they will immediately respond with any remote Group #1 command. To not operate on this universal group, follow the unpairing instructions in Step 3.

Operation with Smart Bridge

Downloading and installing the Feit Electric app

• Search for the Feit Electric app in the App Store or Google Play Store.
• Download and Install the Feit Electric app on your smart unit.
• Connect to a 2.4GHz Wi-Fi network that covers your installation location.
• Follow the instructions in the Feit Electric app & Smart Bridge manual to pair your OneSync lights.

Battery Replacement

1. Replacing the battery
   • To replace the rechargeable battery, remove the lid on the side of the spotlight (AA) by unscrewing the lid screws (2) using a Phillips head screwdriver.
   • Replace with a new lithium-ion 18650 3450mAh 3.6V minimum 12.42Wh or greater.
   • Reattach the lid by securing the (2) screws using a Phillips head screwdriver.

WARNING: Install battery correctly with regard to the polarity(+ and -).

Troubleshooting

The unit will not turn on.| The battery is not making contact.| Loosen the battery cover screws, pull out the battery cover and inspect the battery connection. After inspect on, reinsert the battery.
The battery is not fully charged.| Ensure the solar panel is positioned in a location that prov des full and direct sunlight. If installed in a shady area, the battery will take a longer time to charge, and may not fully charge, and reduce working hours.
The panel is near an external light source that is inadvertently triggering the dusk-to-dawn sensor.| Relocate the panel to an area that does not have any external light sources or remove the external light sources from the panel’s proximity.
The units go out too early.| The battery charge is low.| Allow the batteries to get a full charge by powering off the unit for 1-2 days. Or relocate the unit to an area with direct sunlight. Check panel for dirt, damage, or light obstruct on.
The unit turns on and off continuously.| The solar panel is near an external light source that is inadvertently triggering the dusk-to-dawn sensor.| Relocate or shield the solar panel so that external light sources do not shine directly on it.
The unit turns on for 1O – 20 seconds and then turns off.| The dusk-to-dawn sensor is turning the unit off. This will happen during the daytime.| The unit should automatically turn on at dusk.

Questions, problems, missing parts?
Before returning to store, visit feit.com/help for further assistance.

FEIT ELECTRIC COMPANY I PICO RIVERA, CA | www.feit.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>