COOKE LEWIS CL60CGRF Silver Glass & Stainless Steel Curved Cooker Hood User Manual
- June 4, 2024
- COOKE LEWIS
Table of Contents
CL60CGRF Silver Glass & Stainless Steel Curved Cooker Hood
User Manual
3663602553052 CL60CGRF
5059340350967 CL60CGBLRF
Checking instructions
These instructions are for your safety. Please read the following instructions
carefully before proceeding with the installation and use of this appliance.
WARNING: All installation work must be carried out by a suitably
qualified person, strictly following local building regulations and these
instructions.
To avoid the risks that are always present when you use an electrical
appliance it is important that this cooker hood is installed correctly and
that you read the safety instructions carefully to avoid misuse and hazards.
After unpacking the cooker hood please check that it is not damaged. If in
doubt, do not use the appliance but contact Customer Services on 0800 324 7818
(UK) and 1-800 932 230 (Eire).
Check the package and make sure you have all of the parts listed and decide
upon the appropriate location for your product. If this product contains glass
please take care with fitting or handling to prevent personal injury or damage
to the product. The specification plate shown on this appliance displays all
the necessary identification information for ordering replacement parts. If
you sell the appliance, give it away, or leave it behind when you move house,
please ensure that you pass on this manual so that the new owner can become
familiar with the appliance and its safety warnings.
Safety
- WARNING: There is a risk of electric shock and fire if cleaning is not carried out in accordance with these instructions.
- WARNING: Where applicable, this appliance is supplied with fixings. Please ensure you use the correct fixings suitable for the substrate where the appliance will be installed and that they are able to support the weight of the appliance.
- WARNING: Use only the same size of fittings and mounting screws as recommended in this instruction manual. Failure to follow these instructions may result in electrical hazards.
- WARNING: Switch off the appliance at the main supply before carrying out any maintenance work or cleaning.
- WARNING: Accessible parts may become hot when used with cooking appliances. Children less than 8 years of age shall be kept away unless continuously supervised. Care should be taken to avoid touching the appliance.
- WARNING: Do not flambe under the hood. To avoid the risk of fire, clean or replace the grease filter regularly and closely monitor pans containing hot oil.
- WARNING: This means for full disconnection must be incorporated in the fixed wiring in accordance with the local wiring installation rules for your country. An all-pole disconnection switch having a contact separation of at least 3mm in all poles should be connected during installation.
- WARNING: When the extractor hood is located above an appliance, the minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the hood shall be at least 760mm.
- WARNING: Before connecting the hood, check that the supplied voltage and frequency match with that indicated on the appliance rating plate. Failure to install the appliance in accordance with these instructions may result in a safety hazard. If in doubt, ask for advice in-store or from a qualified installer.
- WARNING: Consult local regulations regarding extraction outlets and ensure these are complied with. Do not connect the hood to ventilation or hot air duct containing combustion fumes from burning gas or other fuels. Confirm that room ventilation is appropriate with the local authorities.
- WARNING: The hood may stop working during an electrostatic discharge (e.g. lightning). This involves no risk of damage. Switch off the electricity supply to the hood and reconnect after one minute.
- WARNING: This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Keep the appliance and its supply cord out of the reach of children less than 8 years old.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a safety hazard.
- Do not install the appliance outdoors in a damp place or in an area that may be prone to water leaks such as under or near a sink unit. In the event of a water leak affecting the appliance, do not use it and contact customer services to arrange for an inspection.
- Do not use flammable sprays in close vicinity to the appliance.
- Please dispose of the packing material carefully. There is a fire risk if cleaning is not carried out in accordance with the instructions. Refer to the Care and Maintenance sections carefully for details on how to clean and replace the aluminum and carbon filters (if fitted).
- The LED lamps in this appliance are not replaceable by the consumer. If a lamp fails, please contact the customer helpline at the end of Care & maintenance to arrange an engineer visit.
- Do not use a steam cleaner for care and maintenance.
- The appliance is not intended to be operated by means of an external timer or a separate remote control system.
- There shall be adequate ventilation of the room when the hood is used at the same time as appliances burning gas or other fuels. Ensure that the negative pressure of the installation site does not exceed 4 Pa (0.04 bar) to ensure combustion fumes are not drawn back into the room.
- Do not use the hood if it shows signs of damage or imperfection. Contact customer services for assistance.
- The manufacturer declines all liability for personal or material damage as a result of misuse or incorrect installation of this appliance.
- The appliance is for domestic use only as an extractor hood.
Installation
All installations must be carried out by a competent person or qualified
electrician. Before connecting the mains supply ensure that the mains voltage
corresponds to the voltage on the rating plate. Direct Connection
The appliance must be connected directly to the mains using an omnipolar
circuit breaker with a minimum opening of 3mm between the contacts. The
installer must ensure that the correct electrical connection has been made and
that it complies with the wiring diagram. The cable must not be bent or
compressed. Regularly check the power plug and power cord for damage. If the
supply cord is damaged, it must be replaced by a special cord or assembly
available from the manufacturer or its service agent.
WARNING: This is a Class I appliance and MUST be earthed This appliance
is supplied with a 3 core mains cable colored as follows:
Brown = L or Live
Blue = N or Neutral
Green and Yellow = E or Earth
The fuse must be rated at 3 Amps.
To avoid the risks that are always present when you use an electrical
appliance it is important that this appliance is installed correctly and that
you read the safety instructions carefully to avoid misuse and hazards. Please
keep this instruction booklet for future reference and pass it on to any
future owners. After unpacking the appliance please check that it is not
damaged. If in doubt, do not use the appliance but contact Customer Services.
The manufacturer declines all liability for damage caused to persons and
objects due to incorrect or improper installation of the appliance. Any
permanent electrical installation must comply with the latest wiring
regulations applicable to your country and for your own safety, a qualified
electrician or contractor should undertake the electrical installation.
The appliance is supplied from the factory to use external ducting (not
supplied). Should you wish to use this in recirculation mode only, please fit
the correct carbon filter (not supplied).
Technical data
Supply voltage | 220-240V– 50Hz |
---|---|
Power consumption – Fan | 90W |
Power consumption – Luminary | 1 x 3W Max |
Power consumption – Total | 93W |
Protection class | I |
Light bulb | Max. 3W |
ILCOSD Code | DBR-2/65-H |
Frequency band | 434MHz |
Information for EU No. 66/2014 and No. 65/2014
A. Information of the cooker hood (www.diy.com)
| Symbol| Value| Unit
---|---|---|---
Model Identification| CL6OCGRF / CL6OCGBLRF
Annual Energy Consumption| AEC hood| 20.| KWh/a
Time increase factor| f| 0.9|
Fluid Dynamic Efficiency| FDE
hood| 32.|
Energy Efficiency Index| EEI
hood| 43.|
Measured air flow rate at best efficiency point| Q
BEP| 237.| M3/h
Measured air pressure at the best efficiency point| P
BEP| 255| PA
Maximum airflow| Q
MAX| Boost: 572.0| W/h
Highest: 401.8
Airflow in normal use| | Highest: 388| M3/h
Lowest: 190
Measured electric power input at best efficiency point| W
BEP| 53| W
Nominal power of the lighting system| W
L| 3.0| W
Average illumination of the lighting system on the cooking surface| E
middle| 79| lux
Lighting Efficiency| LE hood| 26.| lux/watt
Measured power consumption in standby mode| P| –| W
Measured power consumption off mode| P o| OA| W
Sound power level| L WA| Boost: 70| dB
Highest: 63
Lowest: 46
Grease Filtering Efficiency| GFE hood| 66.| %
The measurement and calculation method of the above table was done in
accordance with Commission Delegated Regulation (EU) No 65/2014 & Commission
Regulation (EU) No 66/2014.
B. The following shows how to reduce total environmental impact (e.g.
energy use) of the cooking process.
- Install the cooker hood in a proper place where there is efficient ventilation.
- Clean the cooker hood regularly so as not to block the airway.
- Remember to switch off the cooker hood light after cooking.
- Remember to switch off the cooker hood after cooking.
C. Information for dismantling.
This appliance cannot be dismantled by the user, other than that as shown in
the original assembly of the user manual.
At the end of its useful life, the appliance should not be disposed of with
household waste. Check with your local governmental authority, domestic waste
disposal services or the retailer where the product was bought for recycling
advice.
Troubleshooting
Problem | Possible cause | Solution |
---|---|---|
Excessive vibration. | The appliance is not installed properly on the | |
brackets. | Take down the appliance and check it is properly fixed. | |
The fan blade is damaged. | Switch off the appliance. Repair to be carried out |
by qualified service personnel only.
The fan motor is not fixed tightly.
The light is on, but the fan does not work.| The fan blade is jammed.
The motor is damaged.
Both the light and motor do not work.| The light bulb has blown.| Ring the
customer helpline at the end of the Care & Maintenance section to arrange an
engineer visit.
Power connection lose.| Check the power supply.
Suction
performance reduced.| Speed may be too low.| Select a higher speed.
Aluminum filters are dirty.| Clean the aluminum filters. (See Care and
maintenance section).
The top vent might be obstructed.| Clear any obstruction.
An optional vent kit might be twisted.| Ensure that the vent kit is fitted
according to the manufacturer’s instructions.
The installation may not comply with the manufacturer’s instructions.| The
vent hose should be the correct diameter throughout with no reductions or
restrictions.(See installation section).
Works normally but the cooking smells linger.| The carbon filter is not fitted
in recirculation mode or is full of grease.| Fit carbon filter or replace the
carbon filter (See Care and maintenance section).
This appliance respects laws of the suppression of radio interference. As the Manufacturer has a policy of continuous product improvement, it reserves the right to adapt and carry out any modification considered necessary without prior warning.
Commercial guarantee
At Cooke and Lewis, we take special care to select high-quality materials and
use manufacturing techniques that allow us to create a range of products
incorporating design and durability. That’s why we offer a 2-year guarantee
against manufacturing defects on our Hood.
This Hood is guaranteed for 2 years from the date of purchase if bought in a
store, or delivery, if bought online, for normal (non-professional or
commercial) household use, and without additional charge. You may only make a
claim under this guarantee upon presentation of your sales receipt or purchase
invoice. Please keep your proof of purchase in a safe place. The guarantee
covers all parts and labor costs associated with the repair of the hood, if it
is found to be defective due to faulty materials or workmanship within 2 years
from the date of purchase or delivery subject to the exclusions set out below
and provided it was used for the purpose for which it is intended and subject
to installation, cleaning, care, and maintenance in accordance with the
information contained in the user manual. This guarantee does not cover
defects and damage caused by normal wear and tear of the hood and damage that
could be the result of improper use, faulty installation, storage or assembly,
neglect, accident, modification of the product, or consumable items such as
carbon filters and bulbs.
If the Hood is defective, we will repair it. However, if, during the guarantee
period, the hood becomes irreparable as agreed by an engineer approved by our
authorized agent then we reserve the right, at our discretion, to exchange the
defective hood with a replacement hood. If the same hood is no longer
available an alternative hood will be offered with the equivalent functions
and specifications.
During the service work carried out it may be necessary to remove the built-in
hood from its fitted position. If the hood is glued, grouted or tiled in such
a manner that it cannot be removed, it is the responsibility of the
customer/installer to remove and reinstall the hood to facilitate the repair
or replacement. After the hood has been repaired or replaced any remaining
balance of the guarantee period will apply to the repaired or replaced hood.
Should any person other than an engineer approved by our authorized agent
modify or attempt to repair the hood then the guarantee will be invalid. This
guarantee only applies to the country of purchase or delivery and is not
transferrable to any other country. This guarantee is non-transferable to any
other person or product. Relevant local law will apply to this guarantee. This
guarantee is in addition to and does not affect your statutory rights relating
to faulty goods as a consumer.
Guarantee-related queries should be addressed to a store affiliated with the
distributor you purchased the hood from.
The guarantee is in addition to and does not affect your statutory rights.
To arrange a service call, please contact our customer services on one of the
following Toll-Free numbers, you must contact the number in the country in
which you purchased the hood
-UK 0800 324 7818 uk@kingfisherservice.com
Eire 1-800 932 230
eire@kingfisherservice.com
Recycling & Disposal
Waste electrical products (WEEE) should not be disposed of with household waste. Please recycle where facilities exist. Check with your local governmental authority, domestic waste disposal services or the retailer where the product was bought for recycling advice. The wheelie bin symbol on the product or its packaging indicates that this product cannot be treated as normal household waste. This product must be handed over to an electric and electronic equipment collection point for recycling. On ensuring that this product is disposed of correctly, you
will help to avoid possible negative consequences for the environment and public health, which could occur if this product is not handled correctly.
(EU) Declaration of Conformity
Name and address of the manufacturer or his authorized representative:
Kingfisher International Products B.V., Rapenburgerstraat 175E, 1011 VM
Amsterdam, The Netherlands This declaration of conformity is issued under the
sole responsibility of the manufacturer.
The object of the declaration:
-
Product: Curve glass hood
-
Model: CL6OCGRF CL60CGBLRF
-
EAN: 3663602553052 / 5059340350967
The object of the declaration described above is in conformity with the relevant Union harmonization legislation: -
2014/53/EU Radio Equipment Directive
References to the relevant harmonized standards used or references to the other technical specifications in relation to which conformity is declared: -
EN 60335-1:2012+A11:2014+A13:2017+A1:2019+A14:2019+A2:2019
-
EN 60335-2-31:2014
-
EN 62233:2008
-
EN 55014-1:2006+A1:2009+A2:2011
-
EN 55014-2:1997+A1:2001+A2:2008
-
EN 55014-1:2017+A11.2020
-
EN 55014-2:2015
-
EN 61000-3-3:2013+A1:2019
-
EN 61000-3-2:2019
-
EN 301 489-1 V2.2.3:2019-11
-
EN 301 489-3 V2.1.1:2019-03
-
EN 300 220-2 V3.1.1:2017-02
-
EN 62479:2010
Additional information:
Signed for and on behalf of:
Kingfisher International Products B.V., Rapenburgerstraat 175E, 1011 VM
Amsterdam, The Netherlands
(UK) Declaration of Conformity
Name and address of the manufacturer or his authorized representative:
Kingfisher International Products Limited, 3 Sheldon Square, London, W2 6PX,
United Kingdom
This declaration of conformity is issued under the sole responsibility of the
manufacturer.
The object of the declaration:
-
Product: Curve glass hood
-
Model: CL6OCGRF / CL6OCGBLRF
-
EAN: 3663602553052 / 5059340350967
The object of the declaration described above is in conformity with the relevant legislation: -
Radio Equipment Regulations 2017 as amended
References to the relevant harmonized standards used or references to the other technical specifications in relation to which conformity is declared: -
EN 60335-1:2012+A11:2014+A13:2017+A1:2019+A14:2019+A2:2019
-
EN 60335-2-31:2014
-
EN 62233:2008
-
EN 55014-1:2006+A1:2009+A2:2011
-
EN 55014-2:1997+A1:2001+A2:2008
-
EN 55014-1:2017+A11:2020
-
EN 55014-2:2015
-
EN 61000-3-3:2013+A1:2019
-
EN 61000-3-2:2019
-
EN 301 489-1 V2.2.3:2019-11
-
EN 301 489-3 V2.1.1:2019-03
-
EN 300 220-2 V3.1.1:2017-02
-
EN 62479:2010
Additional information:
Signed for and on behalf of:
Kingfisher International Products Limited, 3 Sheldon Square, London, W2 6PX,
United Kingdom
UK Manufacturer:
Kingfisher International Products Limited, 3 Sheldon
Square, London, W2 6PX, United Kingdom
EU Manufacturer:
Kingfisher International Products B.V.
Rapenburgerstraat 175E
1011 VM Amsterdam
The Netherlands
www.kingfisher.com/products
www.diy.com
www.screwfix.com
www.screwfix.ie
Customer Helpline (Freephone)
UK 0800 324 7818 uk@kingfisher.service.com
Eire 1800 932 230
eire@kingfisher.service.com
To view instruction manuals online, visit
www.kingfisher.com/products
References
- Brico Depôt | Bricolaje, jardín, construcción y climatización
- Brico Dépôt : Magasin de bricolage
- Brico Depôt | Bricolage, construção, jardim e climatização
- Bricolage, jardinage et aménagement de la maison | Castorama
- B&Q | DIY Products at Everyday Low Prices | DIY at B&Q
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>