Meco Smart Home Video Doorbell User Manual
- June 13, 2024
- Meco
Table of Contents
Meco Smart Home Video Doorbell User Manual
Thanks for purchasing and using our product. Please read this quick start guide before using it, and keep it. Manual contents are subject to change without notice in accordance with our policy of continuous product improvement.
What’s in the box
Please consult the below checklist for all the components.
Meet the doorbell
- 2MP Camera
- PIR Motion Sensor
- Speakers
- Indicating LED
- Doorbell Button
- Microphone
- Charging Indicator
- Micro USB Port
- Reset
- Wall-mount bracket
- SD Card Slot
- Battery Compartment
Meet the chime
- speakers
- Reset
- LED Indicator
- USB Port (Type-A/M)
Battery installation
Indoor Chime Screw & Tools The batteries are pre-installed in the doorbell. If
you have taken out the batteries, please note the electrodes when installing
batteries. Please insert the batteries with positive poles upward!
NOTE:
Improper battery installation will cause damage to the internal components and
may result in serious injury.
Battery charging
The batteries inside the doorbell are not fully charged in accordance with
transportation safety regulations. Please charge the batteries with a USB-
compatible wall charger (not included) and the provided USB cable for about
8~10 hours prior to Wi-Fi configuration and installation.
Download the app
Download and install the ‘CloudEdge’ app from Google PlayTM or the App
StoreTM. The App is also available by scanning the QR codes on the right,
using your QR code scanner in your smartphone.
NOTE: Google PlayTM is a trademark of Google Inc. App StoreTM is a
service mark of Apple Inc.
Wi-Fi set up
Before you start the Wi-Fi configuration, please note below:
- The doorbell works with 2.4 GHz Wi-Fi, but not with 5 GHz Wi-Fi.
- Avoid using special characters or symbols like ) either in your Wi-Fi name or password.
- Perform the configuration near your Wi-Fi router.
Launch the CloudEdge APP and register an account with your mobile phone number or email ID. Then start the Wi-Fi Before you start the Wi-Fi configuration, please note below:
Run a test
After setup, tap on the live view window in the app for a test. Then take your
doorbell outside to the installation spot and run a test there. Make sure the
installation spot is covered by a strong 2.4 GHz Wi-Fi signal.
Note:
If the video quality from the doorbell outside is not as good as it was
indoors, you may need to move your router closer to your installation spot or
invest in a Wi-Fi extender.
Live view interface
- Quit live viewing
- Volume on/off
- Stream bit rate
- Speak to the scene
- Notification history
- Setting menu
- HD/SD switch
- Wi-Fi signal status
- Record on the phone
- Cloud storage service
- Battery status
- Wi-Fi signal status
- Screenshot button
- Body detection on/off
Leave a voice message
You can leave a maximum 30-second voice message on the onboard memory of your doorbell, so as to quickly respond to your visitor by a tap on your phone when you are not convenient to answer the doorbell call. The voice message function is available even without a pre-installed Micro-SD card.
STEPS
Setting -> Basic function -> Host Leaves Message -> Record your message ->
Hang off the incoming call and play the voice message.
Installation
Select location
Your doorbell has a 166-degree view angle and a 120-degree human detection
range. It is suggested to mount your doorbell at least 5 feet (160 cm) above
the ground for the best angle of view and motion detection performance.
Mount your doorbell
connect the chime
supply power to the chime
The chime can be powered by a USB-compatible phone charger (DC5V 1A). You can
also plug the chime into the USB port on your PC/notebook to supply power.
Pair with doorbell
- Tap on “···” and enter into Settings-> Basic function, and select the Wireless Chime page.(See to Picture.6)
- Short-click on the reset button behind the chime(See Picture.4), and the LED indicator flashes blue, indicating the device is in pairing mode.
- Tap the “Chime Pairing” button in the APP (See Picture.6), and the doorbell will send a wireless pairing signal to the chime. Pairing succeeds and the indicator on the Chime will be in solid blue. All set! Congrats! You can push the doorbell button to test the result.
Select ringtone
Enter Settings->Wireless Chime, there are 4 ringtones available (See
Picture.6).
Volume control
You can control the volume level for the chime on the Wireless Chime Pairing
page (See Picture.6).
Unbind
- Press and hold the reset button on the chime for about 5 seconds till the indicator flashes blue twice, and the chime will be restored to factory default.
- You can also tap on “One-button Untie” (See Picture.6) in the APP to release the connection between the doorbells and the wireless chimes.
Share device
You can share your doorbell with your family members and friends, by a few setting steps in your APP.
STEPS
Friends -> Search and add your friends to the contact list -> Back to Devices
-> Enter into Settings -> Device Share.
NOTE:
- There is no limitation on number of friends sharing one device.
- Only the administrator got access to the setting menu. Other users can only live view & playback.
- All users can receive doorbell calls and alarm notifications.
- Many users can access to the doorbell simultaneously, to live view or playback.
Key features
Remote view & control
The doorbell will be in “sleep mode” to save power and can be activated
remotely from the CloudEdge App to view and control.
Full duplex audio
The doorbell support 2-way audio intercomm. You can see, hear and speak to
your visitor even when you are not on the go.
Pre-recorded quick response
A max. 30-second voice message can be pre-recorded into the doorbell, which
enables you to quickly reply to your visitor with the voice message when you
are not convenient to answer the call.
PIR human detection
With PIR motion sensor build-in, your doorbell detects human movements in
front of it and sends you motion alerts and snapshots prior to the visitor’s
knock. And it would prevent intrusion/burglary before they actually happen.
Low battery alert
Embed with a power management module, your doorbell can tell you the battery
consumption status, show the estimated usage time and send you low-battery
alerts when it needs a recharge.
Local & Cloud storage
Insert a Micro-SD card (Max. support 128GB) or activate the cloud storage
service to record your video clips.
Specification
Video Doorbell
Indoor Chime
Troubleshooting
Q1: Why I failed to set up Wi-Fi for the doorbell?
A1: The device works with 2.4GHz Wi-Fi only but does not support 5GHz Wi-Fi.
The Wi-Fi network is not good, try to keep the camera near the Wi-Fi router
when setting up. The Wi-Fi password is wrong. Please check if there are
special characters in the password, or if the network is specially encrypted.
Q2: How do I know if I have 2.4G or 5G wifi?
A2: Please check the user manual of your Router or call the network operator
for help.
Q3: It has to be on the same WiFi to see the camera, or is it over the
internet from anywhere?
A3: You can view the camera from anywhere if your camera is well connected to
the internet.
Q4: Do any of the recordings get saved to the cloud? Or is it mainly saved
in the built-in SD card?
A4: It supports SD card recording as well as cloud storage. You can activate
the cloud storage service in App.
Q5: What happens when the SD is full?
A5: When the memory card is full, the camera automatically erases the oldest
footage.
Q6: Does it work with Google Home or Alexa?
A6: Sorry, this model does not support Google Home or Alexa.
Q7: Why does it lose connection to wifi?
A7: Please check the network connection of your phone and the Wi-Fi router. If
the network signal is not strong, you may need to move your router closer to
the device or invest in an extender.
Q8: Can motion detection be disabled?
A8: Yes, sure. The recording is triggered by detected motions. You can set up
the sensitivity or disable motion detection in the setting menu.
Q9: Do we get a charger for the batteries?
A9: Battery charger is not included. Please charge the batteries with a USB-
compatible charger(DC5V 1A~2A) for about 8-10 hours.
Q10: Can we have 2 or more doorbells at the same residence?
A10: Yes, you can add more than one device at the same residence.
Download PDF:Meco Smart Home Video Doorbell User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>