KENWOOD CA-HRN14UT Rear Speaker Wiring Harness Instruction Manual

: June 13, 2024
: KENWOOD

Table of Contents

KENWOOD CA-HRN14UT Rear Speaker Wiring Harness
Product Information
Rear Speaker Harness Installation Instructions
- Installation procedure
Documents / Resources

KENWOOD CA-HRN14UT Rear Speaker Wiring Harness

Product Information

The CA-HRN14UT is a rear speaker harness designed for installation in vehicles. It is manufactured by JVCKENWOOD Corporation, a leading company in the audio and video equipment industry.

Important Notes

Before starting the installation, please read and understand the entire instruction manual.
Ensure that the vehicle’s power is turned off and the battery is disconnected before installing the rear speaker harness.
Only use the CA-HRN14UT harness for its intended purpose and follow all instructions provided.

Rear Speaker Harness Installation Instructions

Refer to the vehicle’s owner’s manual to locate the rear speaker mounting locations.
Carefully route the CA-HRN14UT harness from the stereo unit to the rear speaker mounting locations, making sure to avoid any sharp edges or moving parts.
Connect the appropriate wires of the CA-HRN14UT harness to the corresponding wires of the rear speakers. Ensure that the polarity is correct.
Securely fasten the harness using cable ties or other suitable methods, ensuring that it is not loose or causing any interference with other components.
Double-check all connections to ensure they are secure and properly insulated.
Reconnect the vehicle’s battery and turn on the power.
Test the rear speakers to ensure they are functioning
correctly.

Note: If you encounter any difficulties during the installation process or have any questions, please refer to the latest Instruction Manual available on the following website: https://manual.kenwood.com/encontents/search/

Important Notes
©2023 JVCKENWOOD Corporation. All Rights Reserved. KENWOOD® and eXcelon® are registered trademarks of JVCKENWOOD Corporation. Harley-Davidson®, Electra Glide®, Road Glide®, Street Glide®, Ultra Classic®, Tri Glide®, CVO™, Screamin Eagle® and Tour-Pak® are trademarks or registered trademarks of Harley- Davidson, Inc. and/ or its affiliates and if used or implied are for reference only. There is no affiliation between Harley-Davidson, Inc. and/or its affiliates and JVCKENWOOD Corporation and/or its affiliates. All other trademarks are the property of their respective owners. Specifications are subject to change without notice.

Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new product

Rear Speaker Harness Installation Instructions

Installation procedure

You will see that one end of this harness has two 4-pin connectors. One of these white 4-pin plugs will plug into the “amplified out” on the amp that will power the rear speakers. The amplifier comes with a short harness with a black 8-pin plug and two 4-pin blue plugs. Plug the 8-pin black plug into the amplifier’s input which will power the rear speakers. The second 4-pin plug marked “rear in” on the rear speaker harness will plug into one of the blue 4-pin connectors, noting they will only go in one way.
The harness that will run the rear speakers will pass under the inner fairing on the clutch side of the bike. Loosen the tank’s “chrome console” and run the wires up and over the gas tank, but under the tank’s chrome console. There is a provision on the front of the console for wires to pass under it allowing the power harness to run on the brake side of the filler spout and the rear speaker harness to run on the clutch side of the spout.
NOTE: Although not necessary, the power and rear harnesses can go under the gas tank if you choose to remove and re-install the tank. With the tank removed you will see a factory wire channel where wires pass along the bike’s frame. Removing the top of the channel will allow for the power and rear speaker harness to be safely run under the tank to the battery area. When reinstalling the top of the channel take care not to pinch any wires along the edges of the channel.
Just behind the threaded insert that holds the seat bolt on the back fender, you will see a large factory wire plug. One side of the plug has wires that go to each rear speaker pod. Separate this large factory plug. One plug from the KENWOOD rear harness will plug into each side of the factory plug just separated. They will only go together one way.

For updated information (the latest Instruction Manual, etc.), please visit the following website: https://manual.kenwood.com/en_contents/search/

Documents / Resources

| KENWOOD CA-HRN14UT Rear Speaker Wiring Harness [pdf] Instruction Manual
113PHD4UT, CA-HRN14UT, CA-HRN14UT Rear Speaker Wiring Harness, CA-HRN14UT, Rear Speaker Wiring Harness, Speaker Wiring Harness
---|---