Xunda YK-990 Dog Training Collar User Manual

DOG TRAINING
COLLAR

User Manual

I. Product Overview

Remote Control

LED Display Screen

Receiver

Package Content

 Setting Up

1. products recharged

Connect the USB charging cable, as shown below:
When the Remote Control is charging, the battery icon is bright, and there is a circulating light display. normal 90 minutes full charge and display F. When the Receiver is charging, the red light flashes. normal 60 minutes full charge and the green light on. When fully charged, unplug the plug.

Turn-ON/OFF operation

Remote control:
Press ON/OFF button for 2 seconds, LED screen full display, power on. When it is on, press ON/OFF button for 2 seconds to turn it off. Short Press for display the current battery level. F means the battery is FULL and no need to charge.

Receiver:
Press the ON/OFF button wait until the green light is on and a beep, release the button, power on. In the power-on state, the green light flashes twice every 6 seconds.
When it is on, press the ON/OFF button for 2 seconds, after one vibrate and two beeps, turn off.

Match the Remote Control to the Receiver

1. Only after the remote control and the receiver match successfully, the remote control can control the receiver. One remote control can share time with three receivers, which means one transmitter can share time control three
2. Turn on the remote control, press the “ channel switch ” button to select one of the Dog 1, Dog 2, or Dog 3, the selected dog icon will light up.
3. Turn off the If the receiver is already off, skip this step.
4. Press the “ ON/OFF button ” of the receiver for a while, the green light on and a beep, do not release the button until the red-green LED alternately flashes, then release the Alternately flashing means the receiver has entered the waiting state to match and can receive the code instruction send from the remote control. If the receiver does not receive the code within 15 seconds, it will automatically enter the power-on state.
5. Press the “ static button ”of the remote control for 3 seconds, the dog icon and the signal emission icon will flash, which means the remote control is sending the code matching instruction. At the same time, the receiver will receive the command, alternately flashing stop,3 beeps, indicating the success of
6. Simple test confirm: press the vibration button on the remote control and the receiver will
7. If the receiver wants to rematch under the power-on state, it must first turn off and then repeat 4,5 steps

Config Static Levels

1. The static level can be set on the remote control, and the receiver will execute the static command according to the level set by the remote Static level can be changed at any time.
2. Press the “+” key to increase the current static level, press once to increase 1, press the “-” key to reduce the current static level, press once to decrease 1. The static level varies between 0 and 8 levels, 1 is weakest, 8 is strongest, 0 has no
3. The static function does not support long press continuous emission, can only press a launch once, safety
4. Vibration and sound level can not be adjusted, is

Simple Test before Use

After the above steps are completed, a simple test is commended before use.

1. Beep Test
   Press the “ beep button ” on the remote control once, the signal emission icon and the beep icon both flash, indicating the command is issued. When the receiver receives the command, the buzzer will beep twice. The beep function supports long-press continuous execution.

2. Vibration Test
   Press the “ vibration button ” on the remote control once, the signal emission icon and vibration icon both flash, indicating the command is issued.
   When the receiver receives the command, the green LED is on and vibrates for 0.5s . The vibration function supports long-press continuous execution.

3. Static Test
   Press the “ static button ” on the remote control once, the signal emission icon and static icon both flash, indicating the command is issued. When the receiver receives the command, the red LED on and 2 electrodes output static electricity which intensity according to the command. Place the test neon lamp on the two electrodes and you will see the neon light up.

4. Seek Dog Test
   Quick press the “ seek dog ” button on the remote control once, the signal emission icon and the dog icon both flash, indicating the command is issued. When the receiver receives the command, the white LED will flash 6 times, once per second. The function is mainly used to locate dogs.

5. Lock Keypad Test
   Long press the “ seek dog ” button on the remote control for 2 seconds, the red lock icon will light up. At this time, the keypad lock, the function button is invalid. Again long press for 2 seconds, the red lock icon will go off, the keypad unlocks, everything goes back to normal. The “seek dog” button is multi-function defined.

Training Modes

Press the “channel switch ” button to choose which Receiver you want to control if you match more than one Receiver.

Wearing the Receiver Collar

1. If your dog has thick fur, please separate the fur at the electrodes with a comb to enable them to reach the skin. If not, the dog will not feel the static
2. When wearing the collar, the tightness is at most fitting if one finger can be inserted underneath.
3. Do not put the collar on for over 12 hours , it may cause rashes or discomfort to your dog’s

Power Management

Remote Control

1. The remote control will enter sleep mode if idling for 30 seconds, automatically turn off the LED press any key to wake up.
2. When the power is on, quickly press the ON/OFF button of the remote control to check the current battery power. At this point, the battery icon flashes 3 times, and the
   F| 7| 6| 5| 4| 3| 2| 1| L
   ---|---|---|---|---|---|---|---|---

   4V| 4V| 3.9| 3.8| 3.7| 3.6| 3.5| 3.4| <3.3

LED displays the power number, meaning as follows:

3. Battery status of remote control
   Charging : Battery icon lights up and dynamic cycle LED lights.
   Full charge : the battery icon is bright, the LED screen always shows F.
   Low power : battery icon flashes, showing L, automatically shut down after 10 seconds.

4. Remote control parameters power-down protection, automatic saving, no need to

Receiver

1. When the receiver is power on, the green light flashes twice every 6 seconds to indicate the receiver is in the power on

2. Battery status of receiver
   Charging: red light flashing .
   Full charge: green light always on.
   Low power: red light flash 3 times every second, automatically shutdown after 10 seconds.

3. Matching wait:
   Red & green LED flash alternately, indicating the waiting state of the matching, and the waiting time is 15 seconds.

 Training Tips

1. Reward your dog with food will usually help to achieve the best
2. Do not use the device on dogs aged below 6 months, old, regnant, easily frightened, aggressive, in heat, and dogs not in best of
3. Use verbal commands first, and supplement with a corrective stimulus only as needed. Be consistent with your verbal commands, using the same words every Work with your pet on one behavior at a time to avoid confusion and frustration.
4. For example, use the beeps as a warning by pressing the beep button. The dog will become conditioned to the beep preceding the corrective stimulus and will soon learn to recognize the beep as a warning along with your verbal
5. If your dog shows signs of growling, snarling, biting, or aggression while using the collar, discontinue use immediately and contact a professional trainer for

Important Notice

Regarding you and the product:

1. It is strictly prohibited to open the Receiver in any Doing so will likely compromise the waterproof function and thus void the product warranty.
2. Please use Remote Control and Receivers from the complete set, do not use other products to match with the
3. If you want to test the product, please use professional testing Do not test with hands , so as to avoid accidental injury.
4. I find water at the charging port, please wipe it dry before charging.
5. Beware that interference from the environment can cause the product not to work properly. For example are places with high voltage facilities, communication towers, thunderstorms, large buildings, and strong electromagnetic

Regarding the well-being of your dog:

1. the receiver collar is not a regular collar and not recommended to put on a leash to walk your dog. Doing so during pulling may hurt the dog due to protruding electrodes on the
2. Do not put the collar on for over 12 hours , it may cause rashes or discomfort to your dog’s
3. Do not allow children  or anyone who has little to no experience with training dogs, to handle this training
4. In order to guarantee normal diving function, please insert the waterproof rubber lid over the charging
5. Static stimulation is not a pleasant experience for any dog. Punishment is a harsh way to train Always praise and encourage your dog for good behavior.

Trouble Shooting

1. Not charging
   Make sure the charger and Remote/Receiver is securely connected. Try to use another universal Android USB cable to charge.

2. Static Mode has no effect on my dog.
   Make sure the receiver has enough power. Only both electrodes are simultaneously touched by the dog’s skin shock will work. Try to increase the static level to more than 3. If the dog has long hair, you need to separate dog hair to make electrodes touched.

3. Remote/Receiver does not response
   Recharge the Remote/Receiver, make sure they have enough power. Check the keypad lock, unlock the Remote. If the Remote is locked, there will be a lock icon on the display. If you try the methods above but still fail, please rematch and reconnect Remote with Receivers.

4. Fails to sync up even in a very short distance
   Make sure there is no strong signal interference in your surroundings. Remote’s range could fluctuate subjects to obstacles, electromagnetic field, or even stormy weather.

5. Receivers beep, vibrates, shock by themselves constantly or occasionally.
   Make sure no button of Remote has been pressed or gotten stuck.

Operating Environment & Maintenance

Do not use the product in the circumstances as follow:

1. Do not operate the devices under the temperature of 104°F and above, doing so in such a high temperature will decrease the performance of the
2. Do not use the Remote during snowing, this could lead to water sipping in causing damage to the
3. Do not use the set in places with strong electromagnetic this will greatly compromise the performance of the product.
4. Avoid dropping the devices on a hard surface or inflicting excessive force on
5. Avoid using the devices in an environment flooded with corrosive chemicals, this may lead to color degrading, deforming, or cracking of exterior of the

Maintenance:

1. When not in use, please wipe clean both the Remote and Receiver with mild Turn off the Remote, put on the rubber lid on the Receiver’s charging port, and store them in a cool dry place.
2. During cleaning, wipe with a soft cloth and mild detergent. Do not use hard brushes which may scratch the surface of the device.
3. If the Receiver has gotten dirty, secure the charging port rubber lid secured and wash it thoroughly. Note: do not submerge the Receiver into the water for a long period of time, even though it is
4. If found residues around the charging port’s rubber lid, you should wipe it clean to prevent water from sipping in.
5. If the Remote fell into the water, pick it up quickly and turn off the power. Dry it with a cloth as much as you can and let it out to dry. It should resume function normally once the moisture is dried out.

Terms of Use & Limitation of Liability

1. Use of this product means you accept all the terms and
2. You are not recommended to use this product if your dog is clever and less than 8lbs in weight. If you are not sure whether the product is suitable for your pet dog, please consult a professional handler or contact
3. This product is a professional dog training device and should not be used for other Please do not violate local laws in using this product.
4. We bear no liability for any direct or indirect losses caused by the use or misuse of this product . All risks in using this product shall be borne by
5. Please contact the dealer for parts warranty, goods return or We provide only technical support.
6. We reserve the right to alter the terms, conditions, and notices of this product

Product Certification

DOG TRAINING

| CE-RED| EN301489 EN62368 EN300220 EN62311
FCC-ID| PART-15-C
COLLAR| **** ROHS  (EU)2015/863
California 65                    NA
IP67(only for receiver)    IEC60529

FCC Statements
This device complies with Part 15 of the FCC Rules:
Operation is subject to the following two conditions:(1) This device may not cause harmful interference and (2) This device must accept any interference received including interference that may cause undesired operation.

Warning:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Product Specification Table

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>