IDEMIA Windows L1 RD Software User Manual

Windows L1 RDService Installation
Manual

Revision History

Purpose of document

To provide pre-requisites to run L1 biometric device on Windows System.

Pre-Requisite for running RD Service

Prerequisite for S/W

OS: Windows 10
Web Browser : Chrome (Minimum version 60), Mozilla Firefox (Minimum version v56.0), and Edg
Prerequisites for H/W
MSO 1300 E3 RD Sensor

RD Service Installation Steps

1. Right click on Windows_L1-L0_RDService installer and run the same as an administrator,which will install both L0 & L1 RD service on user’s system.

2. After Installation below folder will be created for both L1 and L0 RD service in C:\ drive.
   IdemiaL1RdService folder will be created for L1 RD service & MorphoRdServiceL0Soft will be created for L0 RD service (Earlier MorphoRdServiceL0Soft folder was as it is getting created for L0 RD Service so there is no change in the same).

3. In case of using proxy server for L1 devices, please go to C:\IdemiaL1RdService\RDService folder and set IsEnabled to true in mc_configuration.xml, enter proxy server IP/URL & port and save the Configuration file.

4. In case it is required to test L1 RD service into pre-production environment then please follow below steps to configure RD service for pre-production environment.
   Go to C:\IdemiaL1RdService\RDService, open mc_configuration.xml and set LoginServer to pre-prod like below and save the configuration (By default login sever is set to Prod only).
   Again in C:\IdemiaL1RdService\RDService folder, open rd_configuration.xml and set RDDetail to PreProd like below and save the configuration ((By default login sever is set to Prod only).

5. After making changes in configuration, please re-start Idemia L1 RD Service from services.

MSO Device Driver Installation

1. Now connect whitelisted Idemia L1 finger print scanner to the system. After connecting the device to the system the device driver will be installed.

2. If device driver is not installed properly then please follow below steps:
   A) Right click on This PC and click on manageB) Now click on Device Manager and check MorphoSmart MSO1300E3 driver under Universal Serial Bus Controllers .If the driver is present there with yellow warning sign( ) like belowC) Then Right click on the device driver icon->click on Update Driver- > “Browse My Computer for Driver Software” -> Let me Pick from a list of device drivers on my computer>Have Disk->Browse- >go to “C:\Morpho\MorphoSmart USB Driver” and
   select “usbBioDriver.inf” in Driver search location and click on Next for completion of manual driver installation and restart the machine for  driver installation finalization .
   After restart, it must be shown as below in the Universal Serial Bus Controllers in device manager:

3.  After successful device driver installation and proper device connection to the system Device registration will start and user will get below popup on screen.

4. User will get below popup on screen once INIT Process will be completed successfully.Finger print Device will be in ready state once user gets above popup message.

RD SERVICE STATUS CHECK AND BIOMETRIC CAPTURE

User can check RD service status, device info and biometric capture through shared RD test page:

1. RD Service Status: Click on RD Service to check the status of RD Service as same should be in Ready state.
2. DeviceInfo: Click on deviceInfo to get the device detail.
3. Capture: Click on Capture to capture biometric of user. Once biometric will be capturedRD service capture response will be generated in XML form.

After successful biometric capture from RD test page user can check biometric capture from client application to perform the transactionpre-production environment.

Version 1.0

Documents / Resources

| IDEMIA Windows L1 RD Software [pdf] User Manual
MSO 1300 E3, Windows L1 RD Software, Windows L1 RD, Software
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>