onn Electronic Flash Model #100012671 Product Guide
- June 8, 2024
- Onn
Table of Contents
Electronic Flash
MODEL: 100012671
PRODUCT GUIDE
September 16, 2020_ V1
PRODUCT FEATURES
- Flash diffuser
- Flash
- Wireless sensor
- SYNC port
- Lock ring
- Trigger
| 1
September 16, 2020_V1
7. Mode indicator (M, S1, S2)
8. Battery cover
9. Power indicator
10. Test shot button
11. Select button for modes
12. Brightness control indicator
13. Power On/Off button
14. Hot-shoe stand
| 2
September 16, 2020_ V1
BATTERY INSTALLATION:
- To install the batteries, open the battery cover, slide the battery bay cover in the direction of the arrows to open.
- Insert the batteries with polarity according to the label inside the battery bay. Make sure the battery polarity is inserted properly or it will not turn on.
- Close the battery cover then slide it in the opposite direction of the arrow to lock it.
FLASH INSTALLATION:
- Unscrew the locking ring by turning it all the way to the left.
- Slide flash to top of camera flash mount. Hold it to make sure it does not fall off.
- Tighten the locking ring by turning it all the way to the right.
Note: Before removing the flash from the camera, please be sure to turn off the flash.
| 3
September 16, 2020_ V1
FLASH OPERATION:
M MODE
In this mode, you can prioritize your flash brightness. Adjust camera settings
by pressing the shutter. The flashlight will flash under the camera
synchronous signal.
FLASH INTENSITY CONTROL
The flash has 8 light intensity levels. 1/128, 1/64, 1/32, 1/16, 1/8, 1/4, 1/2, 1/1.
S1 MODE
This mode is also called “Pre-flash”. In this mode, the flash unit ignores a
single “Pre-flash” from the master flash and only fires in response to the
recorded, actual flash from the master flash. This mode can be used when using
a TTL master flash on the camera.
The flash output setting in slave triggering mode is the same as that in manual mode.
Press the minus (-) button or the plus (+) button to change the brightness. You can use your mini stand to set the flash away from the camera in S1 or S2 slave trigger mode.
Note: To enter S1/S2 mode from the main mode, press the “Mode” button repeatedly until the S1/S2 or indicator lights on the back of the flash.
S2 MODE
This mode is also called “Preflash Cancel. “In this mode, the flash unit
ignores a single “preflash” from the master flash and only fires in response
to the second, actual flash from the master. This mode can be used when using
a TTL master flash on the camera.
Note: To enter S1/S2 mode from the main mode, press the MODE button repeatedly until the S1 or S2 indicator lights on the back of the flash.
The flash output setting in slave triggering mode is the same as that in manual mode. Press the – button or + button to change the brightness. You can use your mini stand to set the flash away from the camera in S1 or S2 Slave Trigger Mode.
| 4
September 16, 2020_ V1
TROUBLESHOOTING:
THE FLASH DOES NOT CHARGE
Make sure that the batteries are installed in the correct direction. If battery appears and blinks on the back of the flash, replace the batteries immediately. Install the batteries even when using an external power source. Make sure that you are using Alkaline or NiMH AA batteries.
THE FLASH DOES NOT FIRE
Make sure that the flash’s mounting foot is securely connected to the camera’s hot shoe. Wait until the flash is fully charged and the flash ready indicator is lit. Make sure that the electrical contacts on the mounting foot and hot shoe are clean. Make sure that the camera’s flash is turned on and the mode is active. If the flash ready indicator does not light, replace the batteries. If battery appears and blinks on the back of the flash, replace the batteries immediately. If the flash is used in slave mode, make sure that the master flash on the camera is turned on and active. If the flash is used in slave mode, make sure that there is a clear line of sight between the optic slave sensor and the camera’s flash. If using a PC sync cable, make sure your connections are secure.
Note: The over-temperature protection may have disabled the flash temporarily. Wait for 10 minutes and try again.
CONTINUOUS FLASHING MAXIMUM TIMES
Power Level 1/1 or ½ = 20
Power level ¼ or 1/8 = 40
Power level 1/16 or 1/32 = 80
Power level 1/64 or 1/128 = 160
SPECIFICATIONS
Guide number = 33 (ISO 100/1M)
Power = 4 x AA batteries
Battery life = 110-1500 times (AA Alkaline batteries recommended)
Recycle time = 3 seconds
Flash mode = M, S1, S2
Color temperature = 5800K
Flash duration = 1/200 seconds – 1/2000 seconds
Flash control = Magnitude 8 brightness control levels (1/128 – 1/1)
Dimensions = 190 x 75 x 55mm
Net weight = 315g
| 5
September 16, 2020_ V1
USING BOUNCE FLASH
By pointing the flash head toward a wall or ceiling, the flash bounces off of the surface before illuminating the subject. This can soften shadows behind the subject for a more natural-looking shot. This is called bounce flash. Hold the flash head and turn it to the angle you want.
Need help? We’re here for you every day from 7 a.m. – 9.am. CST. Give us a call at 1-888-516 2630
1 YEAR WARRANTY:
onn. responsibility with regard to this warranty shall be limited solely to the repair or replacement, at its option, of any product that fails during normal consumer use for a period of one year from the date of purchase. This warranty does not extend to damage or failure resulting from misuse, neglect, accident, alteration, abuse, or improper installation or maintenance. This warranty does not extend to equipment used with the product. If at any time during the one year period following your purchase the product fails due to defects in materials or workmanship, please contact us at TechSupport@Mizco.com to obtain an RMA number and return shipping instructions. For fastest service, have a copy of your product receipt available with the model number, date, and location of purchase. This warranty gives you specific legal rights, and you may have other rights that may vary in certain states or provinces.
WARNING! IMPORTANT SAFETY INSTRUCTION!
Failure to read and follow these safety instructions could result in fire, explosion, electrical shock or other hazard, causing serious and/or fatal injury and/or property damage.
- Do not mix alkaline, standard (carbon-zinc) or rechargeable (ni-cad, ni-mh, etc.) batteries
- Do not modify, disassemble, open, drop, crush, puncture or shred the product
- Do not expose the product to rain or water
- Keep the product away from open flame or sunlight to prevent heat build-up
- Keep the product away from children. This product is not a toy.
- Ensure that all persons who use the product read and follow these warnings and instructions.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
| 6
September 16, 2020_ V1
We ‘d love to hear from you. Scan with your Walmart app and let us know what you think.
September 16, 2020_ V1
onn Electronic Flash Model #100012671 Product Guide – Download
[optimized]
onn Electronic Flash Model #100012671 Product Guide –
Download
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>