Guide Sensmart PC230 Thermal Camera User Guide

: June 12, 2024
: Guide sensmart

Table of Contents

Guide Sensmart PC230 Thermal Camera
Product Information
Product Usage Instructions
IMPORTANT!
LITHIUM BATTERY STORAGE AND OPERATING INSTRUCTIONS
PRODUCT INTRODUCTION
LIST OF ITEMS
PRODUCT COMPONENTS
OPERATION INSTRUCTIONS
FAQS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Guide Sensmart PC230 Thermal Camera

Product Information

Product Name: Thermal Camera
Version: 3.0
Quick Start Guide: Included

Product Usage Instructions

Please refer to the actual product for accurate information as this manual may be inconsistent with the product due to enhancements or version changes.
Content: a. Section 01 b. Section 02 c. Section 03 d. Section 04 e. Section 05 f. Section 06 g. Section 07 h. Section 08 i. Section 09 j. Section 10
Section 01: a. Subsection 1 b. Subsection 2 4. Section 02: a. Subsection 1 b. Subsection 2 c. Subsection 3 d. Subsection 4 e. Subsection 5 f. Subsection 6 g. Subsection 7 h. Subsection 8 i. Subsection 9 j. Subsection 10 k. Subsection 11 l. Subsection 12 m. Subsection 13 n. Subsection 14 5. Section 03: a. Subsection 1 b. Subsection 2 6. Section 04: a. Subsection 1 7. Section 05: a. Subsection 1 8. Section 06: a. Subsection 1 b. Subsection 2 9. Section 07: a. Subsection 1 – A-S-M b. Subsection 2 – STS c. Subsection 3 – T d. Subsection 4 – T e. Subsection 5 – / f. Subsection
IRMIFPIP g. Subsection
A A SM 10. Section 08: a. Subsection 1 b. Subsection 2 c. Subsection 3 d. Subsection 4 11. Section 09: a. Subsection 1 b. Subsection 2 c. Subsection 3 d. Subsection 4
Section 10: a. Subsection 1 b. Subsection 2
IMPORTANT! – This manual covers multiple thermographic cameras, and some functions and instructions may not be applicable to certain models.
NOTES Please follow these rules at all times
- Keep the device stable during use and avoid violent shaking.
- Do not use or store the device in an environment with a temperature beyond the permitted range.
- Do not expose the device directly to high-intensity heat.

LITHIUM BATTERY STORAGE AND OPERATING INSTRUCTIONS

Instructions on lithium battery storage
- Lithium-ion batteries should be stored in a cool, dry place.
- The battery should be fully charged and discharged once every three months and charged to 70% of its capacity.
- Do not transport the battery when the ambient temperature is higher than 65.
Instructions for use of lithium battery
- Use a dedicated charger or charge in the whole device.
- Do not mix the cell with primary batteries or batteries of different capacities, models, and varieties.
- Do not use smelly, hot, deformed, discolored battery, or a battery with any other abnormal phenomenon.
- If the battery is in use or charging, immediately take it out of the electrical appliance or charger and stop using it.
- Charge the battery according to the methods described in this manual and follow the charging steps and warnings to avoid battery heating, damage, or personal injury.
PRODUCT INTRODUCTION
- This product is a hand-held temperature measurement infrared thermographic camera.
- It has 49,152 effective infrared pixels and is equipped with laser, lighting, and visible light.
- It can be connected to an external PC and TF card to meet the needs of different occasions.
LIST OF ITEMS
- Thermal camera (including battery)
- Quick Start Guide
- Data download card
- USB cable
- Wristband
- Adapter
- TF card
PRODUCT COMPONENTS
- Visible lens
- Infrared lens
- Laser lamp
- Focus trigger
- Tripod mount.

This manual may be inconsistent with the product due to product enhancements or version changes, please refer to the actual product.

IMPORTANT!

This manual is a general manual covering multiple thermographic cameras in a product line, which means that some functions and instructions are not applicable to certain model of thermographic camera.

NOTES
Please strictly observe the following rules at all times:

Keep the device as stable as possible during use and avoid violent shaking.
Do not use or store the device in an environment with the temperature beyond the permitted range.
Do not expose the device directly to high-intensity heat radiation source, such as sun, laser, and spot welding machine.
Do not expose the device to dust or moisture. When used in an environment with water, avoid splashing water on the device. The lens shall be covered when the device is not in use.
When the device is not used, please place the device and all accessories in the special packing box.
Do not block the holes on the device.
Do not knock, throw or vibrate the device and accessories to avoid damage.
Do not disassemble the device, which may cause damage to the device and lose the warranty right.
Avoid using TF card for other purposes.
Do not use the device in an environment exceeding the operating temperature of the device, which may damage the device.
Do not use soluble or similar liquids on device and cables, which may cause damage to the device.
Please observe the following rules when wiping the device:
Non-optical surface: if necessary, wipe the non-optical surface of the thermographic camera with a clean and soft cloth.
Optical surface: when using the thermographic camera, please avoid soiling the optical surface of the lens, especially avoid touching the lens with your hands, because the optical coating on the glass surface may be corroded due to sweat on the hands. When the optical lens surface is contaminated, use special lens cloth to carefully clean it.

LITHIUM BATTERY STORAGE AND OPERATING INSTRUCTIONS

Instructions on lithium battery storage

Lithium ion batteries shall be stored in a cool, dry and ventilated environment, away from water source, fire source and high temperature. The storage temperature of the battery must be within the range of – 10℃ ~ 45℃, and the humidity must be 65 ± 20% RH.
Storage voltage and power: the voltage is 3.7V ~ 3.9v (4.2V lithium battery standard voltage system, multi-series combination * corresponding multiple); Power: 30% – 70%.
For long-term storage (more than 3 months), the battery must be placed in an environment with temperature of 23 ± 5 ℃ and humidity of 65 ± 20% RH.
The battery shall be stored according to the storage requirements, and shall be fully charged and discharged once every three months and charged to 70% of the capacity.
Do not transport the battery when the ambient temperature is higher than 65℃.

Instructions for use of lithium battery

Use dedicated charger or charge in the whole device. Do not use modified or damaged charger. The use of high current or high voltage charging may cause problems in the charge and discharge performance, mechanical performance and safety performance of the cell, and may cause heating, leakage or bulging.
The battery must be charged within the ambient temperature range of 0 ℃ ~ 45 ℃. Exceeding this temperature range will reduce the performance and service life of the battery, and there will be problems such as leakage or bulging.
The battery must be discharged within the ambient temperature range of – 20 ℃ ~ 60 ℃.
If the battery is not used for long term (more than 3 months), it may be in over discharge state due to self-discharge characteristics. In order to prevent over-discharge, the battery shall be charged regularly and its voltage shall be maintained between 3.7V and 3.9v. Over-discharge will lead to the loss of cell performance and battery function. If the voltage is lower than the protection plate for a long time, the cell will be deeply discharged to the cell damage. For batteries or battery packs not loaded into the device, it is recommended to charge the battery every 1 month and complete full charging and discharging process of the battery every 3 months; For the battery or battery pack loaded into the device, considering the possible static discharge of the device, the battery shall be charged regularly according to the requirements of the operation manual to prevent battery damage due to power loss.

Warning

Do not charge the battery near fire sources or under extremely hot conditions! Do not use or store batteries near heat sources such as fires or heaters! If the battery leaks or emits an odor, it shall be removed from the place close to the open fire immediately.
When the battery has problems such as bulging and liquid leakage, stop using the battery immediately!
Do not put the battery in water or get it wet!
Do not put the battery into the fire or heat the battery!
Do not connect the battery directly to the wall socket or vehicle cigarette lighter socket!
Do not short circuit the positive and negative terminals of the cell with wires or other metal objects, and do not transport or store the battery with necklaces, hairpins or other metal objects!
Do not pierce the battery case with nails or other sharp objects, and do not hit or step on the battery!
Do not knock, throw or vibrate the battery mechanically!
Do not disassemble the battery in any way!
Do not place the battery in the microwave oven or pressure vessel!
Do not mix the cell with primary batteries (such as dry batteries) or batteries of different capacities, models and varieties!
Do not use smelly, hot, deformed, discolored battery and battery with any other abnormal phenomenon.
If the battery is in use or charging, it shall be taken out of the electrical appliance or charger immediately and stop using!
Charge the battery according to the methods described in this manual, and follow the charging steps and warnings. Incorrect charging can lead to battery heating, damage and even personal injury.

PRODUCT INTRODUCTION

This product is a hand-held temperature measurement infrared thermographic camera. It has 49,152 effective infrared pixels, and is equipped with laser, lighting and visible light. It can be connected to external PC and TF card to meet the needs of different occasions.

LIST OF ITEMS

Thermal camera (including battery) 1
Quick Start Guide 1
Data download card 1
USB cable 1
Wristband 1
Adaptateur Adapter 1
TF card 1

PRODUCT COMPONENTS

OPERATION INSTRUCTIONS

【Take photos and view】
In the real-time observation interface, short press the “trigger button” to obtain the picture, press to save the image or press to abandon the image according to the prompt of the current interface.

View and delete images

Short press to enter the menu interface.
Select the image bar by pressing .
Short press to enter the image file interface.
Short press to view the image. Press up and down buttons to switch the image.
In the image preview interface, short press to delete images.

【Auto focusing】
In the real-time measuring mode (IR, MIF or PIP), short-press the “Trigger Up” button to start the focusing function to display the AF frame on the screen until the image is at its sharpest, and then the AF frame disappears and the focusing is completed.

【Dimming mode】
In the real-time measuring mode, long press the “Menu” button until [A] appears on the upper left of the screen to enter the dimming mode setting. The device supports three dimming modes: Automatic Dimming(A), Semi-automatic Dimming(S) and Manual Dimming(M).

Long press the “Menu” button to enter the dimming mode setting, and then press the “Menu” button to switch the A,S,M mode in turn.
S refers to Semi-automatic Dimming Mode, which can adjust the ΔT value. In S mode, press “Up/Down” button to select the value you want to adjust. When the up arrow is selected, press the “Menu” button to increase the ΔT value. When the down arrow is selected, press the “Menu” button to decrease the ΔT value.
M refers to Manual Dimming Mode, which can adjust Tmax and Tmin values. In M mode, press “Up/Down” button
to select the value you want to adjust. When the up arrow is selected, press the “Menu” button to increase the Tmax and Tmin values. When the down arrow is selected, press the “Menu” button to decrease the Tmax and Tmin values. When the left arrow is selected, press the “Menu” button to increase Tmin value and decrease Tmax value at the same time. When the right arrow is selected, press the “Menu” button to increase Tmax value and decrease Tmin value at the same time.
A refers to Automatic Mode. In this mode, the value is determined according to the real-time scene. And it cannot be adjusted manually.
Press “Return” button to save and exit.

【Image mode】
In the observation mode, select the image mode through of the remote control. The device supports four image modes, namely infrared mode, visible light mode, MIF mode and PIP mode.

【Temperature measurement parameters】
As the temperature measuring parameters may affect the accuracy of measuring results, the parameters need to be set in advance before measuring.

Temperature measuring range: select the appropriate temperature measuring range according to the temperature of the measured object.
Emissivity: it can be adjusted according to the emissivity of the measured object. The emissivity of common objects in this device can also be customized.
Reflected temperature: the impact of the ambient temperature of the currently measured object on the object temperature.
Distance to the object: adjust the distance parameter of the device according to the distance to the measured object to make the temperature measuring more accurate.

【High and low temperature alarm】

Long-press the “Menu” button to enter the menu interface.
Select the “Alarm” option and long-press the “Menu” button to enter the setting interface.
Short-press the “Menu” button to turn OFF to ON.
Press the “Up/Down” button to select high temperature or low temperature, and then adjust the alarm threshold to realize the alarm function.

【USB mode】
There are two USB modes: USB flash drive mode and projection mode.
Enter the Setting menu-USB mode, and press the “Menu” button to switch the mode.
USB flash drive mode: used for file export.

Open the USB cover on the top of the device.
Use USB-TypeC data cable to connect with the computer, and select USB flash drive mode.
Enter the disk folder of the computer, select the images to be exported, copy them to the computer, and view the image files through the analysis software.
After copying, disconnect the USB cable from the computer.

Projection mode: projection of third-party program on PC.

Install a third-party program on the PC, such as “Potplayer”.
Use USB-TypeC data cable to connect with the computer, and select the projection mode.

Click the “Potplayer” drop-down box. Select “Camera” for projection.

【Reset and format the SD card】

Enter the Setting menu – Reset, and press to confirm the reset.
This function will restore the device to the factory settings. Please be careful.
Enter the Setting menu – Format SD card, and press to confirm the formatting.
This function will clear the SD card. Please be careful.

【Emissivity of common objects】