PROGRESS LIGHTING P400352-031 Lowery Linear Chandelier Ceiling Light Instruction Manual
- June 12, 2024
- PROGRESS LIGHTING
Table of Contents
PROGRESS LIGHTING P400352-031 Lowery Linear Chandelier Ceiling Light
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
| B | Canopy | 1 |
HARDWARE CONTENTS (not actual size)
| | | | | | | | | | | | |
---|---|---|---|---|---|---|---|---|---|---|---|---|---
Wire Nut Qty:3| Back plate Qty:1| Screw (#8) Qty:1| Flat washer Qty:1|
Cylinder nut Qty:2| Chain (6Links) Qty:2| Chain Loop (1/8IP) Qty:2| 12″ Pipe
(1/8IP) Qty:8| 6″ Pipe (1/8IP) Qty:2| Nipple (1/8IP) Qty:8| Quick link Qty:2|
Screw #10-32 Qty:2| Toggles Qty:2| Hex nut (1/8IP) Qty:2
Missing parts? Please contact Customer Service at 1-800-446-9107, 8am-8pm (Eastern), Monday – Friday
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble. Operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor
WARNING: If any Special Control Devices are used with this Fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor
CAUTION: All glass is fragile, use care when handling glass shades and bulbs.
PREPARATION
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damage, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder, drill.
CARE AND MAINTENANCE
Shut off main power supply before cleaning product or changing light bulbs. To
clean, wipe with damp cloth.
Do not use abrasive cleaners or cleaners that contain alcohol.
ASSEMBLY INSTRUCTIONS
-
Loosely thread the screws (MM) and the toggles (NN) onto the back plate (BB).
-
Line up the holes in the back plate (BB) with the holes in the junction box. Use a pencil to mark the locations of the two mounting holes. Remove the back plate from the wall.
Drill (2) r/Jl/2 in. mounting holes in the wall for the toggles (NN).
Line up the holes in the back plate (BB) with the drilled holes, press toggles (NN) into the mounting holes drilled and use screws (MM) securing tightly. Then use the mounting screws supplied with the junction box (not included) to secure the back plate (BB) to the junction box.
During this step, determine the hanging length of your fixture by removing
chain links and stems and optionally cutting the electrical and ground wire to
length.
Do NOT cut electrical or ground wires until this overall length is determined.
Leave at LEAST 6 inches MINIMUM of wire length on the canopy ceiling side to
allow for easy connections in step 5.
(Chain links can be spread open with 2 pairs of pliers. Twist the split link
ends in opposite directions and close by squeezing them back together)
-
Determine the hanging height of the fixture (A) and adjust both chains (FF) at this time. Pass wires through stems (HH/JJ) and nipples (KK), tightening stems to assembly as you go to avoid twisting the wires. Pass wires through chain loop (GG) and tighten chain loop (GG) to stem assembly (HH).
Install one end of each of the equal length chains (FF) onto the fixture loops (GG). Close the chain links back together with the pliers. Open the quick link (LL), attach the other end of chain (FF) and canopy loop (B) onto the quick link (LL). Close the quick link. Be sure chains are not twisted and align evenly with one another. With the wires exiting the fastened loop (GG), weave the wire and ground wire through every third chain link (FF), having them exit up through the canopy loop (B) and out the back of the canopy (B).
With the chain links (FF) closed and all the loops (GG) fastened securely, have someone help you hold up the fixture by the canopy (B) and visually inspect the chain lengths, making sure fixture hangs evenly. -
You now need to attach the fixture support cable.
This cable will aid you in supporting the fixture during the wiring connection in step 5.
You will need a helper to help hold up the fixture during this step.
Make sure the supply wire is out of the way from the drill for this step.
Use a #29 drill (0.136) or (3.5mm) bit to create a mounting hole in the side of the junction box.
Next, using the self threaded screw (CC) and flat washer (DD) provided, secure the support cable into the hole you just drilled in the junction box. Tighten securely. -
Strip 3/8″ of insulation from the electrical wire ends. Using the wire nuts (BB), connect the RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire from the outlet box.
Connect the fixture ground wire and supply ground wire together using a wire nut, or fasten both to the ground screw on the mounting strap. Push all the wire connections carefully into the outlet box. -
Position and attach the canopy (B) onto the nipple (BB) and use the hex nut (PP) to secure the canopy (B) tightly to the ceiling.
Next, install the cylinder nut (EE) onto the nipple (BB) to aesthetically hide the hex nut (PP). Tighten it securely to the nipple (BB). -
Install the lamps (not included) into fixture sockets. Use 60-watt MAX incandescent medium base lamp, SBCFL or SBLED.
WARRANTY AND EXCLUSIVE REMEDY:
Progress products, when properly installed and under normal conditions of use,
are warranted to our customers only to be free from defects in material and
workmanship at time of shipment. All warranty claims must be asserted within
one year from date of purchase of the subject items; thereafter, warranty
claims will not be honored. Customers’ sole remedy for a warranty claim or
otherwise shall be limited to repair or replacement of the subject product if
it is shown to have been defective in material or workmanship at time of
shipment. Progress’s sole and maximum liability for a defective
product shall never exceed the cost of the subject product. EXCEPT FOR SUCH A
WARRANTY ANO EXCLUSIVE REMEOY AS STATED (AND THE EXPRESS WARRANTY OF TITLE),
WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY
DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY,
CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER
INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF
OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR
PRODUCTS. Therefore, the customer’s sole and exclusive remedy against us for
breach of the warranty, breach of contract or negligence or strict liability
or otherwise shall be limited to repair or replacement of the subject product
at our option (excluding installation and removal charges which shall not be
our liability) or, if we choose, refund of the purchase price. In no case does
our warranty and exclusive remedy extend to anybody other than our customers.
Our customers are not authorized to extend warranties or remedies on our
behalf to anyone. Such unauthorized extensions of warranties or remedies by
the customer shall remain customer’s responsibility. Customer is responsible
for determining the suitability of our products for customer’s use or resale,
or for incorporating them into objects or for applications which customer
designs, assembles, constructs or manufactures.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>