Delanda D25 Childrens Toy Walkie Talkie Instruction Manual
- June 12, 2024
- Delanda
Table of Contents
Delanda D25 Childrens Toy Walkie Talkie
Product Information
The product is a handheld device that operates on 3 AAA batteries. It comes in two versions – dry battery version and lithium battery version. The device has various features, including SCAN VOX, battery charging, and the ability to restore factory settings.
Product Usage Instructions
Battery Installation:
- Open the battery cover by removing the screws.
- Insert 3 AAA batteries into the battery compartment.
- Close the battery cover and secure it with the screws.
Turning On and Off:
- To turn on the device, press and hold the power key until it powers on.
- To turn off the device, press and hold the power key until it powers off.
Restoring Factory Settings:
- Ensure the device is in the shutdown state.
- Simultaneously press and hold the power key and OK key to turn on the device and restore factory settings.
- After restoration, the default channel/sub tone code will be set to 01/01.
Automatic Shutdown:
- When the device is turned on, it will automatically shut down if there is no operation or signal received for about 40 minutes.
- If you press any key during standby or receive a signal, the automatic shutdown time will restart calculation.
- After automatic shutdown, the device cannot be used normally. You need to manually turn it on to use.
Introduction to functions
Operation guide
Setup menu
- Keep a press of for about 3s to power on, and then, keep a press of for about 3s to power off.
- When the device is power on, press [OK] key to enter “channel” setup menu. At this time, the channel number on the display screen will flash, and then, keep a press of key to select the number. After setup, press key for two times to save and exit the setup menu.
- Or, press [OK] key for two times to enter the secondary menu “group code (CTCSS) for setup. At this time, the group code (CTCSS) iron on the display screen will flash, and then, press key, so that selection of group code (CTCSS) can be conducted. 01-99 group(s) can be selected. OF is to close the group. After setup, press key for two times to save and exit the setup menu.
- Or press [OK] key for three times to enter the secondary menu of “VOX” for setup. After that, press key to select. There are three sensitivities for selection. OF is close. After setup, press key for two times to save and exit the setup menu.
- Or press [OK] key for four times to enter the secondary menu of “call sound selection” for setup. Press [w] key to select. And you can select the first to the tenth call sound. After setup, press key for two times to save and exit the setup menu.
- Or press [OK] key for five times to enter the secondary menu of “keypad tone” for setup. Press key to select. When ON is selected, the keypad tone will be enabled; when OF is selected, the keypad tone will be disenabled. After setup, press key for two times to save and exit the setup menu.
- Or press [OK] key for six times to enter the secondary menu of “tone for emission completion” for setup. Press key to selection. When ON is selected, the tone for emission completion will be enabled; when OF is selected, the tone for emission completion will be disenabled. After setup, press key for two times to save and exit the setup menu.
- Press [OK ]key for the seventh time to save and exit the setup menu.
Power on and power off the interphone
Keep a long press of key for about 3s, there is a sound of “toot”, and the
display screen is on, indicating that the device has been powered on. Keep a
long press of key for about 3s, there is a sound of “toot”, and the display
screen is off, indicating that the device has been powered off.
Emission and receiving of sound by interphone
Note Before communication, the channels of the team members and groups have to
be the same. For setup of channel and group, please refer to point 2 and point
3 in “setup menu of previous page.
- Press key for two times to call the members in the group.
- Hold key to speak to the members in the group. After speaking, release.
- After other members reply. press key again to speak to other members
- In case of multiple groups, switching of group for communication can be conducted.
- During communication, the emission tower icon on the screen will be on.
Adjustment of intercom volume
Press key to turn up the volume, and press key to turn down the volume
There are 8 levels of volume the lowest level is ” ” the highest level is
mugil
Battery life mark
The battery mark displayed on the display screen indicates the battery life in
real time. means full battery life, and means low battery life.
Note
When the battery life mark is it means the battery life is extremely low, at
this time, there may be noise, and the device power off at any time. Timely
charging is required
Product features
Interference elimination (CTCSS)
Interference elimination code can eliminate the interference of the same
channel maximumly, and it also provides multiple selection for you. Refer to
point 3 of “setup menu” for the specific methods for setup. Repetition of this
process can set different combinations for each channel. If CTCSS function is
set for one channel, other calls of different group code of the same channel
can be ignored.
TOT (time-out timer)
The function of time-out timer is to prevent long-time channel occupation and
too long continuous emission duration of the interphone, the device will be
heated therefore. So, TOT limited duration is set. During use, when the
duration of continuous emission of signal exceeds 180s, time-out will be
determined, at this time, the interphone will stop emission automatically to
release the occupied channel and avoid the body from being heated. At this
time, loose key and then press key, emission can be recovered.
Set and send ringtone
You can set the ringtone that you like in the interphone and send the ringtone
to the members in the group to facilitate the members to identify your
callings. Refer to point 5 of “setup menu” for the specific methods of
operation.
VOX function
After VOX function is enabled, during communication, continuous communication
with the members in the group can be achieved without holding key, just like
the hands-free function of mobile phone.
Note
After VOX function is enabled, the product is under long-time emission and
receiving status, the power consumption of the machine will greatly enlarge,
the battery life of the device will be shortened. Please be careful to use
this function.
Scan
Scanning function is used to monitor the channel for transmission or scan the
channel of the interphone of the opposite parties. Keep a long press of key,
the screen will display the scanned channels. When the signal of channel is
scanned, scanning will be stopped. You can hear the sound of the current
channel. At this time, press key, communication can be conducted on this
channel.
Tips: During scanning, pressing of key can change the direction of scanning.
LED flashlight
The LED flashlight of this product can be used for supplemental lighting
within a small scope. When the device is powered on, press key, the LED
flashlight will be powered on, press again, the LED flashlight will be powered
off.
Keyboard lock function
To avoid accidently change of interphone setting, this product is equipped
with the function of keyboard lock. Keep a long press of [OK] key for about
3s, a ” ” icon will be displayed on the screen, and there will be a sound of
“toot”, indicating that the keyboard has been locked, setting, volume increase
and volume decrease cannot be done in menu. After the keyboard is locked, only
key and key can be used. Unlocked: Keep a long press of [OK] key for about 3s
to unlock the keyboard, the ” ” icon in the screen will disappear, and there
will be a sound of “toot” indicating that the keyboard has been unlocked.
Battery charging
Lithium battery version When the battery mark on the display screen is “, it means the product needs to be charged. During charging, please connect the USB cable to the charging port at the bottom of the product. During charging, “ ” will flash, indicating the device is being charged. When the device is fully charged, the battery mark” ” on the screen will stop flashing. When the product is powered on or powered off, this product can be charged.
Restore factory setting
In the shutdown state; Simultaneously press and hold the key and Ok ey to turn on and restore the factory settings. After restoration, the channel/sub tone code is 01/01.
Automatic shutdown
When turned on; When the machine has not been operated for a long time or
receives any signal, it will automatically shut down within about 40 minutes.
When pressing any key during standby or receiving a signal, the automatic
shutdown time will restart calculation; After automatic shutdown, the machine
cannot be used normally. It needs to be manually turned on to use.
Main technical indexes
User safety information
To safely and effectively use this product, please read the following information.
- Before entering inflammable and explosive places, please turn off the power supply of the walkie talkie. It is forbidden to charge in inflammable and explosive environment.
- In order to use the product safely, the product can not be used under the charging state.
- DO NOT use the interphone whose antenna has been damaged, making the damaged antenna cable touch skin may cause slight burning.
- The interphone can only be repaired by professional technicians, DO NOT disassembly without permission. DO NOT disassembly without permission.
- To avoid the problems caused by electromagnetic interference / electromagnetic compatibility, please power off the interphone in the place with the mark of “no interphone”.
- This interphone is not waterproof, please keep it dry.
- DO NOT expose this interphone to direct sunlight or heat source for a long time.
- During emission of this interphone, keep this interphone vertical, and get close to the interphone. If you carry the portable interphone, please ensure that, during emission, the interphone is at least 5cm to body.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Specific Absorption Rate (SAR\ information):
This CHILDREN TOY WALKIE TALKIE meets the government’s requirements for
exposure to radio waves. The guidelines are based on standards that were
developed by independent scientific organizations through periodic and
thorough evaluation of scientific studies. The standards include a substantial
safety margin designed to assure the safety of all persons regardless of age
or health. FCC RF Exposure Information and Statement the SAR limit of USA
(FCC) is 1.6 W/kg averaged over one gram of tissue.
Device types: CHILDRENS TOY WALKIE TALKIE has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the walkie-talkie kept 0mm body- worn Side and 25mm Front of face Side. To maintain compliance with FCC RF exposure requirements, use accessories that maintain 0mm body-worn Side and 25mm Front of face Side separation distance between the user’s body and the back of the walkie-talkie. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
- This product contains small parts that children can use under parental support.
- Do not swallow parts lanyards need to be installed by adults.
- Do not bend, pull or fold the parts.
- Do not throw parts at people or other objects.
- The package contains important information that must be retained;
SCHEUFER Technologies GmbH
Hertleinstrasse 37,91052,Erlangen, Germany
Tel +491631711818
VISHTEC UK CO.,LTD UNIT G25 WATERFRONT STUDIOS, 1 BOCK ROAD,LONDON, UNITED
KINGDOM,E16 1AH;
Tel: +44 20 3286 4115
SHENZHEN DELANDA TECHNOLOGY CO., LTD.
6th Floor, Building 1, Zhongkenuo Industrial Park, Hezhou, Xixiang, Baoan,
Shenzhen, China 518126
Product name: CHILDRENS TOY WALKIE TALKIE
Product model: D25
Made in china
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>