BebeStars NEW Group 2/3 Magic isofix Baby Seat User Manual
- June 12, 2024
- BebeStars
Table of Contents
NEW Group 2/3 (15-36 kgs)
Magic isofix Item 942
STANDARDS
ECE R44/04
User Manual
Your child’s safety depends on you. Proper baby car seat usage cannot be
assured unless you follow these instructions.
DO NOT USE YOUR BABY CAR SEAT UNTIL YOU READ AND UNDERSTAND THESE INSTRUCTIONS
SAFETY NOTES
WARNING
Read this instruction manual carefully.
The correct fitting of the ISOFIT anchoring systems or 3-point vehicle belt is
of vital importance for the safety of your child.
We advise you strongly not to use an unlicensed or modified or without
manufacturer’s instruction product, it is very dangerous.
This is a “Universal” “Specific Vehicle” child restraint. It can be installed
by Vehicle Seat belt separately or by Vehicle Seat belt+ISOFIT. It is for
general use in vehicles and it will fit most, but not all car seats.
The straps holding the restraint to the vehicle should be tight, any straps
restraining the child should be adjusted to the child’s body and should not be
twisted.
Make sure the lap belt is stretched as low as possible over the child’s hips.
DO NOT use any load bearing force points other than those described in
the instructions and marked in the child restraint.
For the future use of the seat, it is important that you keep the instruction
manual carefully. If in doubt,please contact the manufacturer.
This is a “Universal” child restraint. It is approved to ECE R44/04, for
general use in vehicles and it will fit most, but not all car seats.
NEVER leave your child unattended in a car even for a short time.
We do not recommend installing the child safety seat in the front passenger
seat.
DO NOT use a child safety seat if the vehicle seat is equipped with front
airbags, it can be dangerous. This does not apply to so-called side airbags.
It is recommended that the car seat should not be used more than 8 years from
the date of production. The properties of the products may deteriorate due to,
for example, ageing of the plastic wich may not be visible.
DO NOT use a child safety seat that has been in a crash. A crash can
cause damage to the child safety seat that you can not see.
DO NOT modify or attempt to modify the child safety seat in any way.
DO NOT take apart or attempt to take apart this child safety seat etc.
DO NOT use a child safety seat with damaged or missing parts.
DO NOT change the cover or harness, they are the important components.
WARNING
The moving parts of the carseat should not be lubricated in anyway. No
alterations should be made to the product as this could affect part or the
overall safety of the seat.
DO NOT remove the product’s label. There are important notices on labels.
Tell your child that he/she should never play or adjust with the seat.
We advise you strongly not to use a second-hand product, because you are not
sure what has happened to it.
DO NOT place the seat on the edge of countertop or a soft surface like
mattress, the seat mayfall and hurt the child.
Make sure all folda ble passengerseats are fit in place.
Make sure there are no dangerous or corrosive substances in the car, which may
damage the seat.
Make sure that all luggage and objects likely to cause injury in the event of
an accident are properly secured.
The rigid items and plastic parts of a child restraint must be located and
installed so that they are liable, during everyday use of the vehicle, to
become trapped by a movable seat or a door of the vehicle.
Make sure the seat is in a safe position. Do not put any sharp or hard items
around the seat.
Make sure that there are no other items in the clothes or pockets between the
child and the seat belt, as this may cause injury in an accident. Make sure
the vehicle belt is tightly secured and the car seat is correctly installed
each time you use it.
Make sure that the vehicle belt is correctly fastened and does not get stuck
in the car door or other sharp objects, as it may be damaged. Please replace
the vehicle belt if it is damaged. Keep the child in the carseat at all times
while the car is moving.
NOTICE: The seat must be secured in the car, even when it is not on use.
An unsecured seat may injure other passengers in the car in an sudden stop.
Always check whether the seat parts are complete and the seat belt is fastened
correctly before each use.
DO NOT use with 2-point belt. Please install with the 3-point belt.
ONLY use for Forward Facing.
IMPORTANT
The child seat is approved for two different methods of installation.
A. With vehicle’s 3-point safety belt
B. With vehicle’s 3-point safety belt in combination with smart fix
connectors locking into vehicle’s ISOFIX lower anchorages
Important:
- Always used in forward facing passenger seat. We do not recommend to use the child seat in the front passenger seat.
- The safety belt must be approved to ECE R16 or a comparable standard.
- Never use the child seat in the passenger seat equipped with 2-point belt seat.
| Use with the vehicle’s 3-point seat belt
---|---
| Use with 3-point seat belt in combination with Smart Fix
| DO NOT use with 2-point seat belt
KNOW YOUR CHILD CAR SEAT
- Headrest
- Diagonal belt guides and locks
- Armrests
- Cup holder
- Backrest
- Lap belt guides
- Cup holder retainer
- Recline handle
- Headrest adjustment handle
- Seat back
- Smart fix connectors
- Smart fix indicators (green/red)
- Smart fix release button
- Smart fix adjustment button
- Smart fix insertion guides
- Side wings
INSTALLATION GUIDE
Adjusting your child seat
Adjusting the seating position of the child seat
The child seat can be used in multi seating positions for use of all groups.
Pull the recline handle, adjust the seat shell forwards or backwards. Release
the handle in the required position and push until you hear a distinct click
(4-A).
Adjusting the headrest
A correctly adjusted headrest ensures that the diagonal seat belt section is
optimally positioned, and gives your child the optimal protection.
The headrest must be adjusted so that there is a space two fingers wide
between the headrest and your child’s shoulders.
To adjust the height of the headrest to fit your child:
- Reach into the adjustment handle on the back of the headrest and pull it upwards. This unlocks the headrest (4-B).
- Youcan now move the unlocked headrest to the desired height. As soon as you release the adjustment handle, the headrest will lock into place (4-C).
- Place the child seat on the vehicle seat. Have your child sit down in the child seat and check the height. Repeat this process until the headrest is at the optimal height (4-D).
INSTALLATION IN THE VEHICLE
3. Line up the Smart Fix connectors with the Smart Fix guides. Attach
the two Smart Fix connectors to the two anchorage points on the vehicle seat
respectively. You will hear two sound of “Clicks”. And check the Smart Fix
indicator on each side turns to green (6-D).
4. Pull the Smart Fix extend levers at same time to push the child seat
as far back as it will go. Make sure the back of child seat against the
backrest of vehicle seat firmly (6-E).
Unfastening your child seat
To unfasten your child seat, please pull the Smart Fix release buttons on both
sides. Securing your child
Important:
- Before securing your child in the child seat, please make sure the headrest is adjusted to the correct positon.
- Check your vehicle’s manual to see if your vehicle is equipped with ISOFIX lower anchorages choose one method of installat on in the vehicle, either section 5 or, 6 was followed.
INSTALLATION IN THE VEHICLE
Installation with 3-point safety belt
-
Please make sure that the both smart fix connectors are stowed in its original position (the most inside positon). If not, please pull and hold the smart fix adjustment button and push back the smart fix arms back into the seat base.
Repeat the above, to pull back the arm in the other side (5-A). -
Place the child seat on the vehicle seat, make sure the backrest of child seat is flush with backrest of the vehicle seat. Tips: if the headrest of the vehicle seat gets in the way, please remove it or turn it in other way (5-B).
-
Follow the steps in secton 7 “securing your child” to finish the installation.
installation with 3-point safety belt in combination with Smart fix
connectors
Please read the instructions on the use of child restraint systems described
in your vehicle owner’s manual. Find the ISOFIX anchorage points in the
vehicle seat.
Tips: The ISOFIX anchorage points are located between the surface and the
backrest of the vehicle seat.
- Insert two Smart Fix guides to the ISOFIX lower anchorages respectively (6-A / 6-B). Smart Fix guides make it easier to install using the Smart Fix connectors and prevent damage to the upholstery.
- Pull the Smart Fix extend levers on the both sides of seat base to stretch the two arms of Smart Fix connectors respectively (6-C).
SECURING YOUR CHILD
- Have your child sit down in the child seat, and slide the diagonal belt guide locking piece to open it. Pull out the safety belt and guide it to in front of your child to the seat buckle (7-A).
- Buckle it up with an audible ‘Click’ (7-B).
- Guide the lap belt and one end of diagonal belt to the belt guides under the both armrests (7-C).
- Insert the other end of the diagonal belt into the belt guide under headrest, that slide the locking piece to close it (7-D).
- Remove all the slackness of safety belts to the retractor (7-E).
Checklist before you go:
- The diagonal belt must run over in the middle of your child’s shoulder, not in his or her neck (7-F).
- The lap belt must lie as low as possible on your child’s pelvis on both sides.
- No parts of belt should be twisted.
- Make sure the safety buckle is not rested on the lap belt guide (7-G).
CARE & MAINTENANCE
Remove and refitting of seat covers
- Unhook the elastic loops on the back of headrest and backrest to remove covers form the headrest and side wings
- Unhook the cover loops at the bottom of seat base to pull off the cover from it.
Re-fitting the cover
Proceed in reverse order to put on the cover.
Cleaning
The child seat must not be used without the seat cover.
The cover can be washed with a mild detergent using the washing machine’s
cycle for delicate items (30℃).
The colors of the cover may fade if it is washed at more than 30℃. Do not
spin, and never tumble dry in an electric clothes dryer (the fabric may
separate from the padding).
The plastic parts can be cleaned using soapy water. Do not use harsh cleaning
agents (such as solvents).
- Check that you have secured your baby child seat with the seat belt.
- Check that both Smart Fix connectors are properly attached to the anchorage points. Both Smart Fix indicators are green.
If you have any questions, please contact your retailer or manufacturer.
Thank you for choosing Bebe Stars products
FOLLOW US
www.bebestars.gr
bebestarsbygilis
@bebe.stars
bebestarsbygilis
63200 | Nea Moudania | Greece