victron energy BMV-700 MPPT Control Display Manual User Manual

: June 4, 2024
: victron energy

Table of Contents

victron energy BMV-700 MPPT Control Display
Introduction
Mounting
Installation
Operation
Status menu
History menu
Settings menu
Troubleshooting and Support
Warranty
Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

victron energy BMV-700 MPPT Control Display

victron-energy-BMV-700-MPPT-Control-Display-PRODUCT

Introduction

The MPPT Control display is a dedicated display for the Victron Energy SmartSolar and BlueSolar MPPT solar charger range. It can be used to read out the live and historic solar charger data and it can be used to configure solar charger settings.

Examples of live and historic monitoring

PV power, yield, voltage, and current.
Battery voltage, current, and charge stage.
Load output state and current (only available if the solar charger is equipped with a load output).
30-day historical values
Cumulative historic values over the life of the solar charger

The MPPT Control display can be used with the whole range of BlueSolar and SmartSolar MPPT solar chargers. However, for solar chargers rated 60A consider using the better-suited SmartSolar Control display instead.

Power cable

The display ships together with a fused power cable. The supplied power cable is only needed when the display is used with some very early solar charger models that have been long discontinued. These early models shut down when they do not receive solar power. The power cable provides power to the display straight from the battery so that the display is also operational during bad weather or after the sun has gone down.

VE.Direct cable

A VE.Direct cable is needed to connect the display to the solar charger. This cable is not included with the MPPT Control display and needs to be purchased separately. VE. Direct cables vary in lengths from 0.3 up to 10 meters and are available with straight or right-angle connectors. For more information see the VE. Direct cable product page.

Wall mounting enclosure

The housing of the MPPT Control display is tailored towards being flush mounted through a panel. In case flush mounting is not possible a dedicated wall mount enclosure can be used. This enclosure allows for easy wall mounting of the display.

There are two wall mounting options:

Wall mount enclosure for BMV or MPPT Control
Wall mount enclosure for BMV and Color Control GX

Mounting

Drill a hole in a mounting substrate as indicated in the below figure.

Mount the display

Use option A if the mounting substrate is accessible from both sides
Use option B if the mounting substrate is accessible from the front.

victron-energy-BMV-700-MPPT-Control-Display-FIG-6

victron-energy-BMV-700-MPPT-Control-Display-FIG-7

Installation

Connect the solar charger

Connect the MPPT Control display to the solar charger using a VE.Direct cable.
It is not possible to extend the VE.Direct cable, the maximum length can not exceed 10 meters.

victron-energy-BMV-700-MPPT-Control-Display-FIG-8

Connect the power cable (only needed for old style solar controllers)

The supplied power cable is only necessary when the display is used with some very early solar charger models that have been since long discontinued.

Connect the power cable as follows

victron-energy-BMV-700-MPPT-Control-Display-FIG-9

Connect the black wire ring cable lug to the negative battery terminal. If a battery monitor is used in the system, connect the black wire to the system side of the battery monitor shunt instead.
Connect the red cable ring cable lug to the positive battery terminal.
Plug the RJ12 terminal into the power terminal on the back of the display.

Operation

The LCD screen displays the following information

victron-energy-BMV-700-MPPT-Control-Display-FIG-10

A number reading.
The unit of the reading: V, A, W, kWh, h or!
The type of reading: load, battery, PV, min, max or charge stage.
Connection status indicator.

The connection status of the display is indicated by a “double arrow” symbol as indicated in below table.

Indicator	connection status
On	There is a connection between the display and the solar charger
Blinking	There was a connection with the solar charger but the connection is

lost. The last know values will be shown.
Off| There has not been a connection with a solar charger.

The buttons on the front of the display are used to navigate through the solar charger readings and are used when making solar controller and display settings.They have the following functions:

Button	Action

Cancel or Back

|

Select or Confirm

|

Go to next or previous item or

Increase or decrease value

This menu shows the live solar charger readings. The MPPT Control display always starts up in this menu. Press the up and down button cycle through all menu items. These menu items will be displayed in order of appearance as indicated in below table:

victron-energy-BMV-700-MPPT-Control-Display-FIG-15

The history menu shows both the daily and overall solar charger history data. It shows items such as solar yield, battery voltages, time spend in each charge stage and past errors.

To enter and readout the history menu

victron-energy-BMV-700-MPPT-Control-Display-FIG-16

Press the SELECT button, while in the status menu.
Press the up or down button to navigate through the history items.
When arriving at the desired history item, press the SELECT button to see the value of that item.
If an item contains multiple values, press the SELECT button and then the up or down button to browse the various values within that item. For the daily items it is possible to scroll back to 30 days ago (data becomes available over time), a brief popup shows the day number.
To go back to the main history menu press the SETUP button.
To go back to the status menu press the SETUP button again.

All available history menu items are listed in below table, in the order they appear when scrolling through the items.

victron-energy-BMV-700-MPPT-Control-Display-FIG-17

victron-energy-BMV-700-MPPT-Control-Display-FIG-18

In the settings menu, the solar charger and MPPT Control settings can be viewed and changed. Do not change settings unless you know what they are and what the effect of changing these setting can be. Incorrect settings may cause system problems including damage to batteries. When in doubt, seek advice from and experienced Victron Energy installer, dealer or distributor.

To navigate the settings menu

Press the SETUP button for 2 seconds to enter the settings menu
The first menu item is shown.
Navigate to the desired menu item by pressing the up and down button.
Once arrived at the desired menu item, press the SELECT button to view the value the setting has been set to.
To modify this setting press the SELECT button again. teh value will now blink.
Press the up or down button to choose the desired value.
Press SELECT to confirm the change, you will hear a beep and will see the word SAVED. The change is made final.
Navigate to the next menu item, or press SETUP to return to the setup menu.
To leave the setting menu, press the SETUP button again.

It might be possible that the setup menu is locked, in which case the settings can only be viewed. When trying to change the setting the word LOCK is shown.

To unlock the settings menu

Navigate to settings menu item 01 LOCK SETUP
Press the SETUP button, the setting ON is displayed
Press the SETUP button again
Press the down arrow button and select OFF
To leave the setting press the SETUP button.

When SELECT TO EDIT is ON, the current value is shown and a new value can immediately be selected.
When LOCK SETUP is ON, settings can only be changed after setting LOCK SETUP to off.

victron-energy-BMV-700-MPPT-Control-Display-FIG-19

All available settings are indicated in below table, in the order they appear when scrolling trough the menu, together with a basic description of each setting. For the full description of the solar charger settings refer to the solar charger manual. Not all setting listed in below table might be available when connecting to certain models of solar chargers. The solar charger might not have the necessary hardware. For example, not all solar chargers are equipped with a load output.

Some settings might be missing from the settings menu. The MPPT Control display only allows to change the most common settings. More advance settings, like TX and RX port settings, are not accessible via the MPPT Control display. To configure these settings use the VictronConnect App or, for solar chargers 60A and up, use a SmartSolar Control display.

Number	Name	Setting
01	LOCK SETUP	When set to ON, none of the other settings can be changed. If

an attempt is made to change a setting the word “LOCK” is shown together with the setting value.

Set to OFF to unlock, so other settings can be changed.

02| BATTERY VOLTAGE| The system battery voltage; choose between a voltage setting or AUTO.

When set to automatic (AUTO), an A will be shown in front of the voltage setting.

03| BATTERY TYPE| The charge algorithm for a specific battery type; set to FIXED or USER.

When set to FIXED, the rotary switch on the solar charger determines the battery type.

When set to USER, all charging related settings can be edited.

As soon as any of the charging related settings are changed, this setting will automatically set to USER.

Troubleshooting and Support

Consult this chapter in case of unexpected behaviour or if you suspect a product fault. The correct troubleshooting and support process is to first consult the common issues as described in this chapter. Should this fail to resolve the issue, contact the point of purchase for technical support? If the point of purchase is unknown, refer to the Victron Energy Support webpage.

Power issues

The display is powered via the VE. Direct cable or via the power cable. If the display does not power up check these cables.

VE.Direct cable check

Check if the VE. Direct is plugged into the back of the display
Check if the VE.A direct cable is plugged into the solar charger
Make sure the VE. Direct connectors are inserted all the way into the VE. Direct ports.
Check the VE. Direct port pins; ensure that they are not damaged, bent or missing.
Check if the solar charger is able to provide power via the VE. Direct cable when no PV input (at night). Some very early solar chargers models, that have been long discontinued need to have the power cable installed.

Power cable check

Check the fuse in the power cable.
Check if the power cable is plugged into the back of the display.
Check if the power cable is connected to the battery or to another supply voltage.
Check if the supply voltage is between 6.5 and 95 Vdc.

Connection issues

If the display is unable to make a connection with the solar charger or if the text: ”Disconnected “ is scrolling through the screen, the MPPT Control has not established communications with the solar charger. The most likely cause is an issue with the VE. Direct cable.

VE.Direct cable check

Check if the VE. Direct is plugged into the back of the display.
Check if the VE. Direct cable is plugged into the solar charger.
Make sure the VE. Direct connectors are inserted all the way into the VE. Direct ports.
Check the VE. Direct port pins; ensure that they are not damaged, bent or missing.

Settings locked

If the setup menu is locked settings can only be viewed but not changed. When trying to change the setting the word LOCK is shown. To unlock the settings menu see the instruction in the Settings menu [10] chapter.

Warranty

This product has a 5-year limited warranty. This limited warranty covers defects in materials and workmanship in this product and lasts for five years from the date of original purchase of this product. To claim warranty the customer must return the product together with the receipt of purchase to the point of purchase. This limited warranty does not cover damage, deterioration or malfunction resulting from alteration, modification, improper or unreasonable use or misuse, neglect, exposure to excess moisture, fire, improper packing, lightning, power surges, or other acts of nature. This limited warranty does not cover damage, deterioration or malfunction resulting from repairs attempted by anyone unauthorized by Victron Energy to make such repairs. Non-compliance with the instructions in this manual will render the warranty void. Victron Energy is not liable for any consequential damages arising from the use of this product. The maximum liability of Victron Energy under this limited warranty shall not exceed the actual purchase price of the product.

Specifications

Electrical

Supply voltage range when powered from battery| 6.5 – 95Vdc
Supply voltage range when powered via VE.Direct cable| 5Vdc
Power consumption with back-light turned off| < 0.05W
Operating temperature range| -20 – +50°C (0 – 120°C)
Power cable fuse rating| 100mA
Mechanical

Suitability

Suitable for the entire Victron Energy BlueSolar MPPT and the SmartSolar MPPT solar charger range, with the exception of the (since long) discontinued BlueSolar MPPT 70/15.