Alpatronix VX100 Cooling Facial Interface for Meta Quest 2 User Manual
- June 12, 2024
- Alpatronix
Table of Contents
Alpatronix VX100 Cooling Facial Interface for Meta Quest 2
Product Information
The VX100 Cooling Facial Interface is a product designed to a cooling sensation when used with Meta Quest 2 Virtual Reality goggles. It consists of a frame and a cushion that can be placed in the freezer or refrigerator to reach the desired cool temperature. The product is intended for external use only and is not a medical or therapeutic device.
Features
- Provides a cooling sensation
- Compatible with Meta Quest 2 Virtual Reality goggles
- Consists of a frame and cushion
Important Safety Instructions:
- Read all instructions before using the product
- Avoid exposing any electronic devices to water, moisture, steam, excessive sweat, or any other liquids
- Do not use the product if you have reduced physical, sensory, or mental capabilities, unless supervised and instructed by a responsible person
- Close supervision is necessary when using electronic devices near children
Warnings and Precautions
- Do not place the product in the microwave or heat it in any other way
- Individuals with problems in sensing cold should use caution when using the product
- Watch for frostbite and discontinue use if discomfort occurs. Allow the cushion temperature to rise before reapplying or use a paper towel as a barrier between the cushion and skin
- Avoid lying on top of the cushion or putting excessive weight on it to prevent breakage
- Check for leaks before use and discard if tears or leaking is detected
- Do not open the pack and dispose of it if leaking
- Keep the product away from children and use adult supervision when using on children
- If the contents come into contact with skin or eyes, remove the pack and flush with water. If swallowed, seek medical attention immediately
Product Usage Instructions
- Read all instructions before using the product.
- Avoid exposing any electronic devices to water, moisture, steam, excessive sweat, or any other liquids.
- Ensure that you are physically capable of using the product or supervise individuals with reduced physical, sensory, or mental capabilities.
- Supervise children closely when using electronic devices and ensure they do not play with the product in a harmful way.
- Place the cushion in the freezer or refrigerator for approximately 30 minutes or until the desired cool temperature is reached. You may purchase additional cushions to have one readily available.
- Remove the original facial interface from your Meta Quest 2 Virtual Reality goggles by pulling it off.
- Install the VX100 frame onto your Meta Quest 2 Virtual Reality goggles.
- For optimum performance, leave the cushion in place for no more than 20-30 minutes.
- After use, return the cushion to the freezer or refrigerator for at least 30 minutes before reusing.
Note: The VX100 Cooling Facial Interface is not intended to be heated and should not be used as a therapeutic cold pack. It is recommended to check for leaks before each use and discard the product if tears or leaking is detected.
Alpatronix is the registered trademark of Saritek Technical Solutions, Inc. All other brands are registered trademarks of their respective owners.
Important Consumer Safety Notifications
When using electronic devices, basic safety precautions should be followed, including but not limited to the following. Understand that this product is designed to work with other devices, each of which have their own safety considerations. Keep all safety considerations in mind when operating this or any other device by itself, or in combination with one another. You are responsible to ensure using all devices within their safe operational parameters. By using this product, you consent to indemnify and hold harmless Alpatronix and all its agents regarding the use of this product.
- Read all instructions before using.
- Do not expose any electronic devices to water, moisture, steam, excessive sweat, or any other liquids.
- This product is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they are closely supervised and instructed about use of the product by a person responsible for their safety. Close supervision is necessary when any electronic device is used by or near children. Children should be supervised to ensure that they do not play with this device in a harmful way.
- For optimum performance, leave in place for no more than 20-30 minutes. Remove and return to freezer or refrigerator for at least 30 minutes before reusing. SUGGESTION: You may purchase additional cushions to keep in the freezer or refrigerator, so you always have one ready to replace when needed. Visit www.alpatronix.com/products/virtual-reality for more information.
- Always return to freezer or refrigerator promptly for faster reuse.
- Caution: Do not place in microwave or heat in any other way. This product is not intended to be heated.
- Individuals with problems in sensing cold should use extreme caution with this product.
- Watch for frostbite. In case of any discomfort, discontinue use for a few minutes and allow the cushion temperature to rise before reapplying. Alternatively, you may place a paper towel between the cushion and your skin.
- Do not lie on top of cushion or put excessive weight on it, as it could cause it to break. Check for leaks before use. Throw away if tears or leaking is detected.
- For external use only.
- Adult supervision is recommended when using on children.
- This is not a medical or therapeutic device. Do not use this product as a therapeutic cold pack.
- DO NOT OPEN THIS PACK. Check for tears or leaks before use. Throw away if leaking.
- SUGGESTED FIRST AID: If contents contact skin or eyes, remove pack immediately. Thoroughly flush with water. If swallowed, do not induce vomiting. Call a doctor or poison control center immediately.
Parts
Quick Setup Guide
-
Place your cushions in the freezer or refrigerator for about 30 minutes, or until the desired cool temperature is reached. You may purchase additional cushions, so you always have one handy when needed.
-
Remove the original facial interface from your Meta Quest 2 by pulling it off the VR goggles.
-
Install the VX100 frame on your Meta Quest 2 Virtual Reality goggles.
Note : If you wear eyeglasses, you may use the original eyeglass adapter that came with your Meta Quest 2 before installing the Frame. The Alpatronix frame works with eyeglass adapter of your Meta Quest 2. -
Install a cold cushion on the frame.
Hint: To ensure maximum field of view, ensure that the cushion is installed clear of your field of view. -
Each cushion can last up to 20-30 minutes, depending on the starting temperature. Once the cushion no longer provides cold comfort, simply replace it with another one from the freezer or refrigerator
Warranty
To activate the 6-month warranty on your product, visit
https://www.alpatronix.com/warranty and click on the warranty link.
Alpatronix warranty will fully cover your purchase against all defects in
material and workmanship for the entire 6-month period. Most return policies
only allow returns for a period of 14 – 30 days from date of purchase, and
most problems have a knack of happening AFTER that period ends. So, hurry and
register your product to give yourself peace of mind knowing Alpatronix has
got you covered for a whole 6-month period. In case of any problems or need
for support, do not hesitate to contact us at:
PO Box 68030, Anaheim, CA 92618
888-407-7515
support@alpatronix.com
www.alpatronix.com/warranty
Help us in our charitable endeavors!
Alpatronix donates $1 to charity for every review you leave for our products.
We don’t care if it’s positive or negative, we just think every business needs
to do some good in the world. Help us make the world a better place AND help
us and your fellow customers by giving us your valuable feedback.
Thank you for being a contributing citizen of this world.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>