Einhell TE-AV 18/15 Li C Cordless Ash Vacuum Cleaner Instruction Manual

Einhell TE-AV 18/15 Li C Cordless Ash Vacuum Cleaner

Product Information

• Product Name: TE-AV 18/15 Li C
• Product Type: Cordless Ash Vacuum Cleaner
• Model Number: Art.-Nr.: 23.517.00
• Manufacturer: Not mentioned in the provided text

Product Usage Instructions

1. Safety Precautions:

   • Before using the product, read the operating instructions carefully.
   • Follow all safety guidelines mentioned in the user manual.
   • Do not use the vacuum cleaner without the filter.
   • Avoid vacuuming hot ashes, glowing embers, and cigarette butts.
   • Keep the product away from flammable materials.
   • Do not inhale or ingest the collected ash.
   • Wait for the ash to cool down before vacuuming.
   • Regularly clean the filters to maintain optimal performance.

2. Technical Specifications
   No technical specifications are mentioned in the provided text.

3. Assembly Instructions:

   • Install the filters securely before using the ash vacuum cleaner.
   • Attach the swivel casters as shown in Figure 9.

4. Operation:

   • For suction, connect the suction hose (10) to the suction port (5) of the ash vacuum cleaner.
   • For blowing, connect the suction hose (10) to the blowing port (5) of the ash vacuum cleaner.

5. Cleaning, Maintenance, and Replacement:

   • Always remove the battery before performing any cleaning tasks.
   • Clean the ash vacuum cleaner after each use.
   • Clean the filter cartridge (11) by tapping or blowing it with low-pressure compressed air.
   • Contact customer service for replacement parts.

6. Battery Status:

   • All 3 LEDs are lit: The battery is fully charged.
   • 1 LED is blinking: The battery is empty and needs to be recharged.

7. Disposal and Recycling:
   Properly dispose of the product according to local regulations.

8. Storage:
   No specific storage instructions are mentioned in the provided text.
   Please note that the provided text is incomplete and some information might be missing.

Danger!
When using the equipment, a few safety pre-cautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the in-formation is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.

Explanation of the symbols used (see Fig. 14)

1. Danger! – Read the operating instructions to reduce the risk of injury.
2. Cleaning the filter
3. Danger! Wait at least 24 hours before vacuuming an oven or a fi replace in order to be sure that the fi re has gone out and the ash has cooled down. Only for cold ash, see the operating instructions!

Safety regulations

The corresponding safety information can be found in the enclosed booklet.
Warning!
Read all the safety information, instructions, illustrations and technical data provided on or with this power tool. Failure to adhere to the following instructions may result in electric shock, fi re and/or serious injury.
Keep all the safety information and instructions in a safe place for future use.
This equipment can be used by children of 8 years and older and by people with limited physical, sensory or mental capacities or those with no experience and knowledge if they are supervised or have received instruction in how to use the equipment safely and understand the dangers which result from such use. Children are not allowed to play with the equipment. Unless supervised, children are not allowed to clean the equipment and carry out user-level maintenance work.

• Danger! Read the operating instructions be-fore assembling and using the appliance for the first time.
• Remove the battery in the following circum-stances: Whenever the equipment is not in use, before opening the equipment and before all cleaning and maintenance work.
• Never clean the appliance with solvents.
• Never pull the plug out of the socket by pulling the cable.
• Never leave the appliance unattended when operational.
• Keep away from children.
• Never vacuum the following: Burning mat-ches, smoldering ash and cigarette butts, combustible, caustic, inflammable or explosi-ve substances, vapour or liquids.
• This appliance is not suitable for vacuuming dust which can be harmful to health.
• Store the appliance in a dry indoor location.
•  Never use the appliance if it is damaged.
• Only allow the appliance to be serviced by an authorized customer service center.
• Only use the appliance to carry out work for which has been designed.
• Use only genuine accessories and spare parts.
• The guidelines in the operating instructions must be observed. The safety and accident-prevention regulations from the lawgiver are also to be observed.
• Important! Hazardous material must not be extracted with the ash filter.
• Do not extract ashes from prohibited fuels.
•  Do not use the ash filter to extract hot, glowing or inflammable objects (e.g. charcoal, cigarettes …).
• Danger! The ash vacuum cleaner is not sui-table for vacuuming soot or fine dust.
•  Danger! The extracted material must not ex-ceed a temperature of 40°C.
• Danger! If this temperature of the extracted material exceeds 40°C, there is a risk of fire.
• Danger! If the permissible temperature is exceeded, the extractor, the ash filter and the hoses could be damaged.
• Danger! Extracted material which looks as though it has cooled off on the outside may still be hot on the inside. Hot extracted materi-al could be set alight again in the air current.
• Before beginning extraction, please wait until the material is completely cooled off. Hot ashes should not be purged with water, as the sudden temperature difference can cause ruptures to the chimney.
• Wait at least 24 hours before vacuuming an oven or a fireplace in order to be sure that the fire has gone out and the ash has cooled down.
• Check the hoses, the ash filter and the extrac-tor regularly when extracting, to assess levels of heating.
• If the appliance heats up, switch it off, pull the mains plug out and remove the filter bag immediately. Separate the ash filter from the extractor and remove the extracted material. Cold ash is ash which has cooled for a suf-ficiently long time and no longer contains any glowing embers. This can be checked by combing through the ash with a metal object before you use the ash vacuum cleaner.
• Cold ash no longer radiates any perceivable heat.
• After and before vacuum cleaning, empty and clean the tank in order to prevent the accumu-lation of materials which could present a fire hazard in the vacuum cleaner.
• The ash vacuum cleaner is not allowed to be used for collecting harmful dusts (dust class L, M, H).

Layout and items supplied

Layout (Fig. 1-2)

1.  Handle
2. On/Off switch
3. Appliance head
4.  Castors
5. Blow connector
6.  Locking hook
7. Tank
8.  Suction hose connector
9. Suction tube
10.  Flexible hose
11.  Filter cartridge for fi ne ash dust.
12. Filter cleaning button
13. Suction hose holder
14. Battery (not supplied)

Items supplied
Please check that the article is complete as specifi ed in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

•  Open the packaging and take out the equip-ment with care.
• Remove the packaging material and any packaging and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.

Danger!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suff ocating!

•  Original operating instructions
• Safety instructions
  The equipment comes with a chain (z) on the tank bottom. The chain helps to prevent static charging during use.

Proper use

• The cordless ash vacuum cleaner is suitable for vacuuming cold dry ash or cold dry material from fi replaces, charcoal ovens, ash-trays or barbe-cues.
• The equipment is to be used only for its prescri-bed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or inju-ries of any kind caused as a result of this.
• Please note that our equipment has not been de-signed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

Technical data

• Motor power supply: 18 V DC
• Container volume: 15 l
• Sound pressure level LpA: 75 dB(A)
• Uncertainty KpA: 2 dB (A)
• Weight (without battery): approx. 3 kg

Battery and charger
Please use only batteries and chargers from the
Power-X-Change series, e.g. 1.5 Ah and 6 Ah batteries and the charger model Power-X-Charger 3A.

Before starting the equipment

Before you connect the equipment to the battery make sure that the data on the rating plate are identical to those of the battery.
Warning!
Always pull out the battery before making ad-justments to the equipment.

Assembling the appliance
Fitting the appliance head (Fig. 3-6)

• The appliance head (3) is fastened to the con-tainer (7) by the locking hook (6). To remove the appliance head (3), open the locking hook (6) and remove the appliance head (3). When fi tting the appliance head (3), make sure that the locking hook (6) locks into place correctly.
• Plug the vacuum tube (9) onto the end of the suc-tion hose (10).
• Fit the suction hose (10) onto the connection (8) and turn until securely attached.

Fitting the fi lter
Notice!
Never use the ash vacuum cleaner without fi lters. Always make sure that the fi lters are securely seated.

Removing/fi tting a fi lter (Fig. 7)
Turn the fi lter cartridge for fi ne dust (11) to the left and remove it from the equipment head (3). Assemble in reverse order. Check that the pleated fi lter is securely seated at all times!
Important!
If no fi lter (11) is fi tted to the equipment head (3), it will be impossible to switch on the ash vacuum cleaner. The equipment is fi tted with a switch (Fig. 8/Item e) which must be activated to permit operation.

Fitting the castors (Fig. 9)
Fit the castors (4) as shown in Fig. 9.

Charging the battery (Fig. 11)

1. Take the battery pack out of the equipment. Do this by pressing the side pushlock buttons.

2.  Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger (d) into the socket outlet. The green LED will then begin to fl ash.

3. Insert the battery pack (14) into the battery charger (d).

4. In the section entitled „Charger indicator“ you will fi nd a table with an explanation of the LED indicator on the charger.

• The battery pack can become a little warm during the charging. This is normal.
• If the battery pack fails to charge, check:
  • whether there is voltage at the socket outlet
  • whether there is good contact at the charging contacts
• If the battery pack still fails to charge, send
  • the charging unit
  • and the battery pack to our customer service center.
• To ensure that items are properly packaged and delivered when you send them to us, please contact our customer service or the point of sale at which the equipment was purchased.
• When shipping or disposing of batteries and cordless tools, always ensure that they are packed individually in plastic bags to prevent short circuits and fi res.
• To ensure that the battery pack provides long ser-vice, you should take care to recharge it promptly. You must recharge the battery pack when you notice that the performance of the device drops. Never allow the battery pack to become fully di-scharged. This will cause it to develop a defect.

Fitting the battery (Fig. 10)
Slot the battery (14) into the mount and push it forward until you hear the battery engage.

Battery capacity indicator (Fig. 12)
Press the button for the battery capacity indicator (a). The battery capacity indicator (b) shows the charge status of the battery using 3 LEDs.

All 3 LEDs are lit:
The battery is fully charged.

2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.

1 LED fl ashes:
The battery is empty, recharge the battery.

All LEDs blink:
The battery temperature is too low. Remove the battery from the equipment, keep it at room tem-perature for one day. If the fault reoccurs, this me-ans that the rechargeable battery has undergone exhaustive discharge and is defective. Remove the battery from the equipment. Never use or charge a defective battery.

Operation

ON/OFF switch (Fig. 1/2)
Press the ON/OFF switch (2) to switch the equip-ment ON and OFF.

Blowing (Fig. 1/2)
Connect the suction hose (10) to the blow con-nector (5) of the ash vacuum cleaner.

Filter cleaning system (Fig. 13)
The equipment has a fi lter cleaning system which enables the pleated fi lter to be cleaned when the-re is a drop in suction performance.
Important! The fi lter cleaning system works only when the equipment is in operation.
When the suction performance drops, proceed as follows:

1.  Close the end of the hose so that no air can be drawn in any longer.
2. Press and hold the fi lter cleaning button (12) for approx. 4 s.
3. Repeat step 2 four or fi ve times.

Cleaning the appliance head (Fig. 1/Item 3)
Clean the appliance regularly with a damp cloth and some soft soap. Do not use cleaning agents or solvents; these may be aggressive to the plas-tic parts in the appliance.

Cleaning the container (Fig. 1/Item 7)
The container can be cleaned with a damp cloth and some soft soap or under running water, de-pending on the amount of dirt.

Cleaning the fi lters (Fig. 7)
Clean the fi lters (11) e.g. by tapping and brushing or by blowing out with compressed air at low pressure.

Cleaning, maintenance and ordering of spare parts

Danger!
Always pull out the battery pack before starting any cleaning work.

Cleaning

• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible.
• We recommend that you clean the appliance immediately after you use it.

Servicing
At regular intervals and before each use, check that the fi lters in the ash vacuum are securely fi tted.

Ordering replacement parts:
Please quote the following data when ordering replacement parts:

• Type of machine
• Article number of the machine
• Identification number of the machine
• Replacement part number of the part required
  For our latest prices and information please go to www.Einhell- Service.com

Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offi ces.

Storage
Store the equipment and accessories in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging.

Charger indicator

The charger is connected to the mains and is ready for use; there is no battery pack in the charger

On| Off| Charging

The charger is charging the battery pack in quick charge mode. The char- ging times are shown directly on the charger.

Important! The actual charging times may vary slightly from the stated

charging times depending on the existing battery charge.

Off| On| The battery is charged and ready for use.

The unit then changes over to gentle charging mode until the battery is fully charged.

To do this, leave the rechargeable battery on the charger for approx. 15 minutes longer.

Action:

Take the battery pack out of the charger. Disconnect the charger from the mains supply.

Flashing| Off| Adapted charging

The charger is in gentle charging mode.

For safety reasons the charging is performed less quickly and takes more time. The reasons can be:

–         The rechargeable battery has not been used for a very long time.

–         The battery temperature is outside the ideal range.

Action:

Wait for the charging to be completed; you can still continue to charge the battery pack.

Flashing| Flashing| Fault

Charging is no longer possible. The battery pack is defective.

Action:

Never charge a defective battery pack. Take the battery pack out of the charger.

On| On| Temperature fault

The battery pack is too hot (e.g. due to direct sunshine) or too cold (below 0° C).

Action:

Remove the battery pack and keep it at room temperature (approx. 20° C) for one day .

DISPOSAL

For EU countries only

• Never place any electric power tools in your household refuse.
• To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.
• Recycling alternative to the return request:
• As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations. This does not apply to any ac-cessories or aids without electrical components supplied with the old equipment.
• The reprinting or reproduction by any other means, in whole or in part, of documentation and papers ac-companying products is permitted only with the express consent of the Einhell Germany AG.
• Subject to technical changes

Service information

• We have competent service partners in all countries named on the guarantee certifi cate whose contact details can also be found on the guarantee certifi cate. These partners will help you with all service re-quests such as repairs, spare and wearing part orders or the purchase of consumables.
• Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.
  Category| Example
  ---|---
  Wear parts| Suction tube, Battery
  Consumables| Pleated filter, foam filter, coarse filter
  Missing parts|

Not necessarily included in the scope of delivery!

In the eff ect of defects or faults, please register the problem on the internet at www.Einhell-Service.com. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:

•  Did the equipment work at all or was it defective from the beginning?
• Did you notice anything (symptom or defect) prior to the failure?
• What malfunction does the equipment have in your opinion (main symptom)?Describe this malfunction.

Warranty certifi cate

Dear Customer,

• All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

  1.  These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not aff ected by this guarantee. Our guarantee is free of charge to you.

  2. The warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectifi cation of said defects on the product or the replacement of the product, whichever we prefer.
     Please note that our devices are not designed for use in commercial, trade or professional applica-tions. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.

  3. The following are not covered by our guarantee:

  • Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by ex-posing the device to abnormal environmental conditions or by lack of care and maintenance.
  • Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for ex-ample by dropping it).
  • Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device.
  4. The guarantee is valid for a period of 24 months starting from the purchase date of the device. Gu-arantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fi tted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fi tted. This also applies if an on-site service is used.
  5. To make a claim under the guarantee, please register the defective device at:
     www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identifi cation will not be possible. If the defect is co- vered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.

• Of course, we are also happy off er a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.

• Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as set out in the service information in these operating instructions.

EU DECLERATION OF CONFIRMITY

References

• Einhell Service
• Einhell Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>