better bathrooms ARIMB018 Matt Black Slotted Sprung Basin Waste User Manual
- June 12, 2024
- Better Bathrooms
Table of Contents
better bathrooms ARIMB018 Matt Black Slotted Sprung Basin Waste
Product Information
The product is a range of basin wastes available in different finishes and
configurations:
- ARIMB018 – Matt Black Slotted Sprung Basin Waste
- ARIBB020 – Brushed Brass Slotted Basin Waste
- CHSBW001 – Chrome Slotted Basin Waste
- ARIMW005 – Matt White Slotted Basin Waste
- ARIVRG005 – Vapour Rose Gold Slotted Basin Waste
- ARIMB019 – Matt Black Unslotted Sprung Basin Waste
- ARIBB021 – Brushed Brass Unslotted Basin Waste
- CHUBW001 – Chrome Unslotted Basin Waste
- ARIMW006 – Matt White Unslotted Basin Waste
- ARIVRG006 – Vapour Rose Gold Unslotted Basin Waste
Product Usage Instructions
Single-person assembly: We always recommend using professional
tradespeople to install your product.
Installation
Note: Silicone sealant can be used.
- Unscrew the locknut (4) and remove the plastic gasket (3) and rubber washer (2).
- Insert the drain body (1) from above the basin.
- For the slotted basin waste, make sure the slot lines up with the overflow on the basin.
- Install the rubber washer (2), plastic gasket (3), and tighten with locknut (4).
- To fill the basin, the Clicker mechanism requires pressing down the clicker dome (1), and pressing it again to release the water.
- Check all the joints for leaks.
Troubleshooting
Issues
- Loose drain body
- Water leak
Check
- Is Locknut (8) fully tightened?
- Is the clicker dome (1) fully tightened?
- Is there damage or dirt with the O-ring (2)?
- Is there damage or dirt with the rubber washers (5 or 6)?
Maintenance and Cleaning
To maintain the surface of your product, wipe with a clean damp cloth and wipe
dry. Do not use any abrasive cleaning agents or materials. If any harsh
chemicals come into contact with the surface of the product, rinse and wipe
clean immediately.
Product
ARIMB018 – Matt Black Slotted Sprung Basin Waste ARIBB020 – Brushed Brass
Slotted Basin Waste CHSBW001 – Chrome Slotted Basin Waste ARIMW005 – Matt
White Slotted Basin Waste ARIVRG005 – Vapour Rose Gold Slotted Basin Waste
ARIMB019 – Matt Black Unslotted Sprung Basin Waste ARIBB021 – Brushed Brass
Unslotted Basin Waste CHUBW001 – Chrome Unslotted Basin Waste ARIMW006 – Matt
White Unslotted Basin Waste ARIVRG006 – Vapour Rose Gold Unslotted Basin Waste
- Single-person assembly
- We always recommend using professional
- tradespeople to install your product
Congratulations on your purchase
And welcome to our growing gang of savvy shoppers We’re on a mission to bring
you extraordinary bathroom products, for less. From modern to traditional
style ceramics, plus the gorgeous fixtures, fittings and furniture to match.
So, you can fall in love with your space every single day. As one of the UK’s
largest independent bathroom stores, we’ve received countless awards;
including the National Business Awards UK, the Digital Entrepreneur Awards and
being placed on The Sunday Times Fast Track 100. We hope your new product goes
above and beyond your expectations. However, should any problems occur,
please:
- log in to your account and contact our customer services team via your self-serve portal – betterbathrooms.com/CustomerAccount/Login
- contact us via betterbathrooms.com/content/contact-us
Important information
- Please read these instructions thoroughly and retain for future reference
- Installation must be carried out in compliance with The Water Fittings Regulations and Scottish Water Byelaws.
- The system must be flushed prior to installation, else it might clog the filter and the following phenomenon occurs: discharged water volume is small, or temperature cannot be controlled well.
- Pressures must be equal for optimum performance
- Please do not connect hot and cold water supply lines in reverse. This could result in hot water flowing from cold line and cause scalding.
- The feed-water temperature of water shall not exceed 85°C.
- Exceeding 85°may cause scalding, the service life of faucets might be shortened, or the faucet might be damaged.
- After installation, please make sure the faucet is securely mounted and checked for leaks.
Parts / Diagrams
| No | Part Description |
|---|---|
| 1 | Clicker dome |
| 2 | O-ring |
| 3 | Piston kit |
| 4 | Drain body |
| 5 | Rubber Washer |
| 6 | Rubber Washer |
| 7 | Plastic gasket |
| 8 | Locknut |
Dimensions
Tools required
- Seal tape
- Spanner
Installation
Slotted/Unslotted Basin Waste
Note: Silicone sealant can be used.
- Unscrew the locknut(4), and remove the plastic gaskets (3) and rubber washer(2).
- Insert the drain body(1) from above the basin. For the slotted basin waste, make sure the slot lines up with the overlfow on the basin.
- Install the rubber washer(2), plastic gasket(3) and tighten with locknut(4)).
- To fill the basin, the Clicker mechanism requires pressing down the clicker dome and pressing it again to release the water.
- Check all the joints for leaks.
Troubleshooting
| Issues | Check |
|---|---|
| Loose of drain body | • Is locknut(8) fully tighten |
• Is the clicker dome(1) fully tighten
Water leak| • Is there damage or dirt with the o-ring(2)
• Is there damage or dirt with the rubber washers(5 or 6)
Maintenance and Cleaning
To maintain the surface of your product, wipe with a clean damp cloth and wipe dry, do not use any abrasive cleaning agents or materials. If any harsh chemicals come into contact with the surface of the product, rinse and wipe clean immediately.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>