MuxLab 500553 240W Dante 2 Channel Power Amplifier User Manual

MuxLab 500553 240W Dante 2-Channel Power Amplifier

Product Information: Dante 2-Channel Power Amplifier 240W

• Model: Dante 2-Channel Power Amplifier 240W
• Power (Stereo Mode): 120W x 2, 8Ω RMS output (steady state), per channel @ < 1 % THD+N
• Power (Bridged Outputs): 120W x 2, 4Ω RMS output (steady state), per channel @ < 1 % THD+N
• Frequency Response: High Pass Filter
• Signal to Noise: 12.3 V (+24 dBu)
• Input Sensitivity: 12VDC
• Trigger Connectors: 214mm(W) x 249.8mm(D) x 44mm(H)
• Gain Value: 1.94 Kg
• Output Connectors: 100 – 240 VAC, 50 – 60 Hz, 350W
• Maximum Input Level: 2 years
• Trigger In/Out: 500553
• Dimensions: Dante 2-Channel Power Amplifier 240W (UPC: 627699005538)

Safety Precautions

To ensure the best performance from the product, please read all instructions carefully before using the device. Save this manual for future reference.

• Follow basic safety precautions to reduce the risk of fire, electrical shock, and injury.
• Do not dismantle the housing or modify the module. It may result in electrical shock or burns.
• Do not open or remove the housing of the device as you may be exposed to dangerous voltage or other hazards.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture and do not install this product near water. Keep the product away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on the housing, unplug the module immediately.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
• Using supplies or parts not meeting the product specifications may cause damage, deterioration or malfunction.
• Refer all servicing to qualified service personnel.
• Install the device in a place with adequate ventilation to avoid damage caused by overheat.
• Unplug the power when left unused for a long period of time.
• Information on disposal of devices: do not burn or mix with general household waste, please treat them as normal electrical waste.

Copyright Notice
All contents in this manual are copyrighted, and cannot be cloned, copied, or translated without the express permission of MuxLab Inc. Product specifications and information in this document are for reference only, and the content may be updated from time to time without prior notice.

Introduction

The Dante 2-Channel Power Amplifier 240W (Model 500553) features a Dante slot card that accepts the digital signal from the Dante network and converts it to an analog audio signal using it as the input source of the amplifier. Simply use “Dante Controller” to route a signal from source devices that are on the same Dante network. Its space-saving 1/2 rack design allows for quick installation and provides flexibility to mix and match with other 1/2 rack products to save valuable equipment rack space.
This powerful class D amplifier is combined with features such as 12V trigger control, audio sensing, volume gain adjustment, short circuit protection and overheating protection.

Product Usage Instructions

1. Before using the device, read all instructions in the user manual carefully.
2. Ensure that all included accessories are present. If any items are missing, contact the supplier from whom you purchased the unit.
3. Connect the Dante Interface to a Dante network switch using the provided cable.
4. Make sure the network LED on the Dante Interface illuminates yellow, indicating a successful connection to the network.
5. If the network LED turns green or blinks, it means the unit has obtained an IP address and is communicating with the network.
6. In Auto mode, the amplifier will be triggered on when it receives a signal from the Dante Network.
7. On the front panel, the ON button keeps the unit powered on at all times, while the AUTO button activates standby mode after 15 minutes of no signal detection.
8. To power on the unit using an external trigger, provide 12VDC at the Trigger input on the rear panel.
9. The LED indicator on the front panel will be green when the unit is powered on and red when in standby mode.
10. The amplifier supports two channels of audio and can deliver 120W per channel at 8Ω or 4Ω, or a bridged output of 240W at 4Ω or 8Ω.
11. It features a high pass filter for frequency response control and provides short circuit protection and overheating protection.
12. The amplifier has a natural cooling system without a fan and meets Energy Star power consumption limits of less than 0.5W in standby mode.

Features

• Two-channels audio amplifier with Dante integration
• Supports 2 x 120W @ 4/8 ohm, 1 x 240W @ 4/8 ohm, or 70/100V constant output for multiple speakers
• Switch for High Pass Filter
• Selection for Power-Up mode.
• Natural cooling without Fan
• Short circuit protection
• Overheating protection
• Red Led (Front Panel) to indicate Standby mode is active
• Power down after 15 minutes of no signal and meets with Energy Star power consumption limits of < 0.5W in standby

Package Contents

• One (1) Dante 2-Channel Power Amplifier 240W
• Three (3) Mounting Ears
• One (1) Wall mounting bracket
• One (1) Power cable IEC320 C13
• One (1) 4-pin Phoenix Connector
• One (1) 2-pin Phoenix Connector
• Four (4) Rubber feet
• One (1) User manual (available via download)

Notes ： Confirm that the product and accessories are all included. If not, please contact the supplier from which you purchased the unit.

Specifications

Operation Controls and Functions

Front Panel

Rear Panel

Dante Audio Interface

• 2×2 audio channels
• I2S digital audio format
• 16, 24 or 32-bit audio samples (per device or per channel)
• 44.1 KHz, 48KHz, 88.2KHz and 96KHz sample rates
• Power supply: PoE, 5V 36mA

Network Interface

• Standard 100Mbps Ethernet RMII Ethernet interface with MDIO Hardware time-stamping, supporting sample-accurate playback
• Transmit flows: 2 (unicast or multicast)
• Receive flows: 2 (unicast or multicast)
• Latency from 2ms

Dante Controller

The Dante 2-Channel Power Amplifier 240W is built in Dante interface and compatible with the software “Dante Controller”.

The “Dante Controller” software can be downloaded free of charge from the Audinate website (Audinate is the company that owns the Dante technology).

To install the software on the computer, please visit the link:
https://www.audinate.com/products/software/dante-controller

And the “User Guide” of “Dante Controller” is available at the following link:
https://www.audinate.com/resources/technical-documentation

Connection Diagram

2321 Cohen
St-Laurent , H4R 2N7
Québec, Canada
Tel: 514-905-0588
Fax: 514-905-0589
Toll free: 1-877-689-5228
info@muxlab.com 
salesteam@muxlab.com
www.muxlab.com
Dante 2-Channel Power Amplifier 240W 500553
Follow us:

References

• Dante Controller | Dante
• Resources Archive | Dante

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>