RYOBI R18QS Cordless QuietStrike Impact Driver Instruction Manual
- June 12, 2024
- RYOBI
Table of Contents
R18QS
ORIGINAL INSTRUCTIONS
Cordless QuietStrike Impact Driver
Instruction Manual
Important!
It is essential that you read the instructions in this manual before
assembling, maintaining and operating the product.
Safety, performance, and dependability have been given top priority in the
design of your impact driver.
INTENDED USE
The product is intended to be used only by adults who have read and understood
the instructions and warnings in this manual, and can be considered
responsible for their actions.
The product is intended for fastening and removing screws and bolts.
Do not use the product in any way other than those stated for intended use.
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
IMPACT DRIVER SAFETY WARNINGS
- Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and
regulations.
Follow all special requirements on packaging and labelling when transporting
batteries by a third party. Ensure that no batteries can come in contact with
other batteries or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or tape. Do not
transport batteries that are cracked or leaking. Check with the forwarding
company for further advice.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise and the operator should pay special attention to avoid the following:
- Damage to hearing caused by noise Wear suitable hearing protection and limit exposure.
- Injury to the eyes Wear protective eye shields or goggles when using the product.
- Injury caused by vibration Limit exposure. Follow the instructions in Risk Reduction.
- Electric shock caused by contact with hidden wires. Hold the product only by insulated services.
- Injury caused by dust Dust created by operating the product can cause respiratory injury. Wear appropriate dust control mask with filters suitable for protecting against particles from the material being worked on.
RISK REDUCTION
It has been reported that vibrations from handheld tools may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, numbness, and blanching of the fi ngers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking, and work practices are all thought to contribute to the development of these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:
- Keep your body warm in cold weather. When operating the unit, wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
- After each period of operation, exercise to increase blood circulation.
- Take frequent work breaks. Limit the amount of exposure per day.
If you experience any of the symptoms of this condition, immediately
discontinue use and see your doctor about these symptoms.
WARNING
Injuries may be caused, or aggravated, by prolonged use of a tool. When using
any tool for prolonged periods, ensure you take regular breaks.
KNOW YOUR PRODUCT
- Auto-load chuck
- Tri-beam LED
- Direction of rotation selector
- Variable speed switch trigger
- MAG TRAY™ screw holder
- Bit storage
- Single bit
- Belt clip
- Belt clip screw
- Battery port
MAINTENANCE
WARNING
The product should never be connected to a power supply when assembling parts,
making adjustments, cleaning, performing maintenance, or when the product is
not in use. Disconnecting the product will prevent accidental starting that
could cause serious injury.
- When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.
- Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt and carbon dust.
- Do not, at any time, let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact with plastic parts. They contain chemicals that can damage, weaken, or destroy plastic.
- Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.
- For greater safety and reliability, all repairs should be performed by an authorised service centre.
LUBRICATION
All of the bearings in the product are lubricated with a suffi cient amount of
high grade lubricant for the life span of the product under normal operating
conditions. Therefore, no further lubrication is required.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing of as waste. The machine, accessories, and packaging should be sorted for environmentfriendly recycling.
SYMBOLS
| Safety alert
---|---
**| CE conformity
| EurAsian Conformity Mark
| Ukrainian mark of conformity
| Please read the instructions carefully before starting the machine.
| No-load speed
V**| Volts
| Direct current
| Revolutions or reciprocations per minute
| Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
SYMBOLS IN THIS MANUAL
Note
Speed, minimum
Speed, maximum
The following signal words and meanings are intended to explain the levels of
risk associated with this product:
DANGER
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result
in minor or moderate injury.
CAUTION
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
Product specifications
18V Quiet STRIKE™
Impact Driver
Model
Voltage
Coupler
Switch
– Variable speed
Impacts per minute
No load speed
Maximum torque
Weight – excluding battery pack
Weight – according to EPTA Procedure 01/2003
Product specifications
Measured sound values determined according to EN 60745:
A-weighted sound pressure level
Uncertainty K
A-weighted sound power level Uncertainty K
Wear ear protectors.
The vibration total values (triaxial vector sum) determined according to EN
60745:
Impact tightening of fasteners of the maximum capacity of the tool Uncertainty
K
Battery and charger
Compatible battery pack (not included) Lithium-Ion
Compatible charger (not included)
WARNING
The vibration emission level given in this information sheet has been measured
in accordance with a standardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a preliminary assessment of
exposure. The declared vibration emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration
emission may differ. This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is running but not
actually doing the job. This may significantly reduce the exposure level over
the total working period. Identify additional safety measures to protect the
operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
GUARANTEE
In addition to any statutory rights resulting from the purchase, this product
is covered by a guarantee as stated below.
-
The guarantee period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no guarantee provided in case of professional or commercial use.
-
There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is clearly displayed in stores and/or on packaging. The end user needs to register his/her newly-acquired tools online within 8 days from the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the data which are required to enter online and they have to accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty. Your statutory rights remain unaffected.
-
The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or material at the purchase date. The guarantee is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or being incorrectly connected. This guarantee does not apply to:
– any damage to the product that is the result of improper maintenance
– any product that has been altered or modified
– any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
– any damage caused by non-observance of the instruction manual
– any non CE product
– any product which has been attempted to be repaired by an nonqualified professional or without prior authorization by Techtronic Industries
– any product connected to improper power supply (amps, voltage, frequency)
– any damage caused by external influences (chemical, physical, shocks) or foreign substances
– normal wear and tear of spare parts
– inappropriate use, overloading of the tool
– use of non-approved accessories or parts
– carburettor after 6 months, carburettor adjustments after 6 months
– power tool accessories provided with tool or purchased separately.
Such exclusions include but is not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide
– components (parts and accessories) subject to natural wear and tear, including but not limited to carbon brushes, chuck, power cord, auxiliary handle, sanding plate, dust bag, dust exhaust tube -
For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
-
A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start of the guarantee period. Exchanged parts or tools become our property. In some countries delivery charges or postage will have to be paid by the sender.
-
This guarantee is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.
AUTHORISED SERVICE CENTRE
To find an authorised service centre near you, visit
http://uk.ryobitools.eu/header/service-and-support/service-agents.
EC declaration of conformity
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Herewith we declare that the product 18V Quiet STRIKE™ Impact Driver
Brand: Ryobi
Model number: R18QS
Serial number range: 44482801000001 – 44482801999999 is in conformity with the
following European Directives and harmonised standards 2006/42/EC, 2014/30/EU,
2011/65/EU,
EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:2015,
EN 60745-1:2009+A11:2010, EN 60745-2-2:2010
RoHS documentation is compiled according to EN 50581:2012 ****Andrew John Eyre
(BEng, CEng, MIET)
Vice President, Regulatory & Safety
Winnenden, May 27, 2016
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Techtronic Industries GmbH
Max-Eyth-Straße 10,
71364 Winnenden, Germany
961153006-02
References
- Ryobi Tools
- Ryobi Tools
- SAV Ryobi France: Pièces détachées et réparations Ryobi : le service client Ryobi
- Ryobi Norge | Elverktøy, ONE+, Hagemaskiner, 36V
- Ryobi Tools
- Ryobi Tools
- Ryobi Tools UK
- Ryobi Danmark | Elværktøj ONE+, Havemaskiner, 36V
- Ryobi Tools
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>