maytronics Dolphin Liberty 200 Cordless Robotic Pool Cleaner Instructions

maytronics Dolphin Liberty 200 Cordless Robotic Pool Cleaner

Product Information

The Robotic Pool Cleaner LIBERTY is a high-performance pool cleaning device designed to efficiently clean the floors and walls of your swimming pool. It comes in two models, LIBERTY 200 and LIBERTY 300, each offering different features and functionalities.

Pool Cleaner Parts

• Settings and status indicator
• Power button
• Battery indicators
• Inductive charger connection
• Extra filter panels* (only for LIBERTY 300)
• Filter basket
• Grab hook
• Clicker* (only for LIBERTY 300)
• Charger

Specifications

Robot

• pH: 7.0-7.8
• NaCl: 5000 ppm, Max.
• Battery: Lithium-ion | 5,000mAh | 25.2V@5Ah / 126Wh
• Charger protection: IP 54

Water Conditions
The LIBERTY pool cleaner is designed to work effectively in various water conditions.
Features and Indications
The LIBERTY 300 model offers additional features for customization and energy efficiency.

Cycle Selector – LIBERTY 300
Use the Cycle Selector to customize the cleaning mode to focus on the pool floor only. Follow the steps below:

1. Press the ON button to activate until the LED lights up.
2. Press the ON button again for 3 seconds until the purple LED blinks 3 times.
3. Place the robot in the pool, and within 30 seconds, it will start cleaning the pool floor. After a cleaning cycle of 90 minutes, the robot will return to the default Floor and Walls mode.

Eco Mode – LIBERTY 300
Use the Eco Mode to keep your pool floor clean for a week on one charge. The robot will automatically clean the pool floor for up to 30 minutes, 3 times a week, with 48 hours between cleaning cycles. Follow the steps below:

1. Press the ON button to activate until the LED lights up.
2. Press the ON button again for 6 seconds until the purple LED light turns green.
3. Place the robot in the pool, and within 30 seconds, it will start working.

Error

In case of error notification, please refer to troubleshooting or contact customer care at www.maytronics.com.

Removing The Robot Out Of The Pool

1. Place the black capsule of the clicker in the water.
2. Ensure that the clicker is no more than 8 meters (26 feet) away from the robot.
3. Shake the clicker for at least 3 seconds.

After a few seconds, the robot will climb to the waterline and wait there for 60 seconds to be collected. Then, you can easily take the robot out of the water.

Using Grab Hook (for LIBERTY 200)

1. Follow the provided instructions in the user manual to use the Grab Hook to remove the robot from the pool.

To clean the filter basket:

1. Open the filter cover.
2. Upon opening the filter cover, the handle will lift independently.
3. Lift up the basket.
4. Open the latch to release the bottom lid and remove the debris.
5. Clean the filter basket with a hose.

Periodic Cleaning – Recommended at Least Once a Month

Follow the periodic cleaning instructions provided in the user manual to ensure optimal performance of your LIBERTY pool cleaner.

POOL CLEANER PARTS

SPECIFICATIONS

Robot

• Water temperature range: 6°C-35°C / 43°F-95°F
• Water depth range: 0.4m-2.5m / 1.33ft-8.2ft
• Motor protection: IP 68
  • Chlorine – 4 ppm, Max.
  • pH – 7.0-7.8
  • NaCl – 5000 ppm, Max.
  • Battery Lithium-ion | 5,000mAh | 25.2V@5Ah / 126Wh
• Charger protection: IP 54

Water Conditions
Use only the robotic pool cleaner in the following water conditions:

• Chlorine: 4 ppm max.
• pH : 7.0 – 7.8
• Temperature: 6°C – 35°C / 43°F – 95°F
• NaCl: 5000 ppm max.

FEATURES AND INDICATIONS

Cycle Selector – LIBERTY 300
Use Cycle Selector to customize cleaning mode to “Floor only”:

1. Press ON to activate until the LED lights up.
2. Press ON again for 3 seconds until the purple LED blinks 3 times.

Place the robot in the pool, and within 30 sec, it will start cleaning the pool floor.
After cleaning cycle (90 minutes each cycle), the robot will return to default “Floor and Walls” mode.

Eco Mode – LIBERTY 300
Use Eco Mode to keep your pool floor clean for a week on one charge. The robot will automaticly clean the pool floor for up to 30 min, 3 times a week, with 48 hours between cleaning cycles.

1. Press ON to activate until LED lights up.
2. Press ON again for 6 seconds until the purple LED light turns green.

Place the robot in the pool, and within 30 sec, it will start working.

• Temperature Warning
  In case of temperature warning notification, place and charge the pool cleaner in a protected and shaded area, at a temperature range of 6°C – 35°C / 43°F – 95°F.

• Error
  In case of error notification, please refer to troubleshooting.

or contact customer care – www.maytronics.com.

CHARGING RECOMMENDATIONS

• When the battery is low and all indicators are off – the cleaner is on standby mode. Connect to charger to wake it up.
• Always Charge the pool cleaner in a protected and shaded area at a temperature range of 6°C – 35°C / 43°F – 95°F, until you see 3 green bars in the battery indicator panel (up to 6 hours).
• Make sure that the charger surface and power unit surface are clean, and there is no object between the robot and the charger.

REMOVING THE ROBOT OUT OF THE POOL USING CLICK-UPTM (for LIBERTY 300)

1. Place the black capsule of the clicker, in the water.
2. Make sure the clicker is no more than 8 m/26 ft away from the robot.
3. Shake the clicker for at least 3 seconds

After a few seconds the robot will climb to the waterline and will wait there for 60 seconds to be collected.
****Take the robot easily out of the water.

• The robot will climb the nearest wall, and will wait for 60 seconds on the waterline.
• If you can’t reach this wall, wait for the robot to move to another wall. Shake the clicker and the robot will climb to the waterline.

Removing The Robot Out Of The Pool Using Grab Hook (for LIBERTY 200 )

• Standard pole. Not included.
• After finishing its cleaning cycle, the robot will stop next to a random wall, so you will be able to pick it up with the grab-hook.

CLEANING THE FILTER BASKET

It is highly recommended to clean the filter basket after each cleaning cycle.
Note: Do not let the filter basket dry out before cleaning.

Cleaning after use – removing and cleaning the filter basket

PERIODIC CLEANING – RECOMMENDED AT LEAST ONCE A MONTH

Dismantle the 2 ultra-fine filter panels of the basket, according to the following steps:

TROUBLESHOOTING

The robot doesn’t charge

| Robot’s Battery LEDs are blinking in a special pattern (central LED

– then right and left LEDs). The issue occurred while the robot was connected to the charger

| 1. In case the robot feels hot to the touch: charge the robot in a shaded location or when the temperature is low, for example: overnight / indoors.

2. In case the robot feels cold to the touch: try charging the robot in a warmer location.

The Power Unit doesn’t show any LEDs at all| Try connecting the charger to a different power outlet. Make sure that the charger LED is on.

The Power Button LED is red

| 1. Try disconnecting the charger from the Power Unit and connecting it back a few times.

2. Check whether an object is blocking the connection between the charger and the Power Unit.

The charging process stops, and the Power Button LED is blinking red for a short period of time| 1. Make sure that the charger is connected properly.

2. Check whether an object is blocking the connection between the charger and the Power Unit.

Charging progress is stuck: one of the battery LEDs is blinking and doesn’t switch to the steady light after a long period of time

| 1. Check that the charger LED turns on.

2. Make sure that the charger is connected properly.

3. Check whether an object is blocking the connection between the charger and the Power Unit.

4. Charge overnight in a cooler location.

The battery is not full after charging

| ****

The robot’s battery discharges while the robot is turned off

| Fully charge the robot (until all battery LEDs are steady green), make sure that the robot is turned off. Do not start the cleaning process. Check the battery status after 2 days.

If the battery charge level is significantly lower – contact Customer Care.

Red LED light appears above the power button

|  | Make sure there’s nothing stuck in the tracks or brushes. Clean the filter and make sure it’s not clogged.

Disconnect and reconnect the charger 3 times.

The robot will not start the cleaning cycle. The Power Button LED is red

| The charging process works properly

The robot finishes a 90-minute cleaning cycle

During the Eco mode and Cycle Selector, the robot will climb the walls even if configured otherwise

The robot will not respond to Click-UpTM properly – will start the

cleaning cycle instead of waiting at the wateline

| ****

Contact Customer Care: wecare@maytronics.com

The charger is connected to the robot| Disconnect the charger and press on the robot’s power button to operate.
The charger is disconnected from the robot. The charging process works properly| ****

Contact Customer Care: wecare@maytronics.com

OFF-SEASON STORAGE

Before off-season or storing the robot during the winter – we recommend charging the battery at least 50% (2 green bars in the battery indicator panel). Recommended storage temperature range: -10°C – 40°C / 14°F – 104°F. After off-season storage, charge the robot to its fullest.

WARNINGS AND CAUTIONS

Warnings

• Remove the robotic pool cleaner from the pool before allowing people to enter the pool.
• When examining the robotic pool cleaner, make sure the robotic pool cleaner is switched OFF.
• Charge the battery only in the temperature range between 6°C to 35°C / 43°F to 95°F
• Keep the robotic pool cleaner out of the reach of children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. Cleaning and maintenance shall not be made by children.
• Use only the original battery charger.
• The battery charger must be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.
• The power cord is not user-replaceable. If the power cord is damaged, stop using the battery charger and contact the service center for repair. Do not use extension cord to connect the battery charger to electric supply; provide a properly located outlet.
• DO NOT USE the robotic pool cleaner and/or its battery / power pack in case of mechanical damage to the robotic pool cleaner and/or its battery.
• To avoid the risk of fire and burns, DO NOT open, crush, heat, or burn the battery case.

Cautions

• Keep hands and fingers away from impeller motor area and driving belt mechanism to avoid injury.
• Position the battery charger at least 3.5 m / 12 ft from pool edge during operation.
• For continuous protection against possible electric shock, place the battery charger at least 11 cm / 4 in above ground.
• When lifting the robotic pool cleaner, take care to prevent back injury.
• Do not use the robotic pool cleaner if you have added liquid flocculant or any other clarifier to the pool water. These substances obstruct and damage the robot filters.
• The Lithium-Ion battery in this product is non-replaceable. It should be recycled at certified battery electronics recyclers that accept batteries. Batteries should NOT be discarded in the trash or put in municipal recycling bins. Do not disassemble the battery.

Contact us

North America

• US 1-888-365-7446
• Canada 1-855-634-8572
• customersupport@maytronicsus.com.

France

• +33 (0)4 42 98 14 90
• support@maytronics.fr.

Australia, NZ, South Africa

• 1 300 693 657
• infoau@maytronics.com.

Rest of the world / Maytronics HQ

• 00 800 69694141 (toll-free number)
• 00 972 77 96 14 204 (international call)
• wecare@maytronics.com.

Robotic Pool Cleaner LIBERTY | User Instructions

References

• Dolphin Robotic Swimming Pool Cleaner | Maytronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>