sip 05719 Welding Trolley User Manual

sip 05719 Welding Trolley

Product Information

The Welding Trolley Manual 05719 is a versatile piece of equipment designed to accommodate a welder, accessories, and a gas cylinder.
With its two wheels, it allows for easy mobility of the welder and large gas bottle.
This welding trolley is suitable for use in garages, engineering workshops, and agricultural workshops.

Product Specification

• Model: 05719
• Dimensions (D x W x H): 550mm x 490mm x 1140mm
• Packing Dimensions (L x W x H): 600mm x 540mm x 1190mm
• Weight: 16kg / 35lbs
• Load Capacity: 99kg / 218lbs

Warnings

1. Always use the trolley on a level surface to prevent dangerous falls of compressed gas cylinders.
2. Never position the trolley on an inclined surface to avoid tipping over and causing damage or injury.
3. Before using, ensure all fasteners are tight and the cart is assembled according to the provided instructions.
4. Keep the instructions safe for future reference.
5. Always move the trolley using the trolley handle. Never pull the trolley by the welder, welding torch, or leads as it may cause tipping.
6. Do not remove parts from the trolley while it is being moved.
7. Always securely chain the compressed gas cylinder using the chains provided.
8. Never weld on the compressed gas cylinder or the cart.
9. Failure to follow these warnings may result in property damage, personal injury, or even fatality.

Product Usage Instructions

Assembly

Contents:

• 1 x Trolley Frame
• 1 x Wheel Axle
• 2 x Split Pin
• 1 x Strap c/w Clips
• 2 x Wheels
• 4 x Wheel Washers
• 2 x Bottle Chain

Fitting the wheels:

• Lay the trolley frame down with the handle pointing up. Fit the axle through the chassis. Refer to Figs 1 & 2.
• Fig.1:
• Fig.2:
• Fit washers, wheels, and split pins. Refer to Figs 3, 4, 5 & 6.
• Fig.3:
• Fig.4:
• Fig.5:
• Fig.6:
• Repeat the above steps for the other side of the axle.

Fitting the retaining strap:

• Follow the steps illustrated in Figs 7, 8, 9, 10, 11, 12 & 13.

• Fig.7:

• Fig.8:

• Fig.9:

• Fig.10:

• Fig.11:

• Fig.12:

• Fig.13:

• Fitting the chain:

• Fit the chain as shown in Figs 14 & 15. Adjust it to suit your bottle size.

• Fig.14:
  Fig.15:

• Please dispose of packaging responsibly by recycling it at a local amenity tip.

• Do not dispose of electrical equipment or batteries with your domestic waste. Use a recognized recycling agent or a disposal facility offered by your supplier to protect the environment and allow for the recycling of raw materials.

• If you need help or advice regarding this product, please contact your distributor or SIP directly:

• TEL: 01509 500400

• Email: sales@sip-group.com or t echnical @sip-group.com

• Website: www.sip-group.com

• SIP Industrial Products Limited Gelders Hall Road Shepshed Loughborough Leicestershire LE12 9NH United Kingdom

• Please read this manual before using

Product Description

• The welding trolley accommodates a welder, accessories & gas cylinder.
• Equipped with two wheels, it is very easy to move the welder and large gas bottle.
• It is an ideal piece of equipment to use in garage, engineering & agricultural workshops.

Product Specification

Model| Dimensions

D x W x H (mm)

| Packing Dimensions

L x W x H (mm)

| Weight

(kg/lbs)

| Load Capacity

(Kg/lbs)

---|---|---|---|---
05719| 550 x 490 x 1140| 600 x 540 x 1190| 16 / 35| 99 / 218

Warning

1. Always use the trolley on a level surface. Compressed gas cylinders are dangerous should they fall.
2. Never position the trolley on an inclined surface. It may tip over, causing damage and possible injury.
3. Before using, make sure all fasteners are tight and cart is assembled as per the provid-ed instruction
4. Keep instructions safe for reference.
5. Always move the trolley by using the trolley handle. Never pull the trolley by the welder, welding torch , leads etc as this may cause the trolley to tip over.
6. Do not remove parts from the trolley whilst it is being moved.
7. Always chain the compressed gas cylinder securely with the chains provided.
8. Never weld on the compressed gas cylinder or this cart.
9. Failure to follow these warnings may result in property damage, personal or fatal injury

Assembly

Contents:-

• 1 x Trolley Frame 1 x Wheel Axle
• 2 x Split Pin
• 1 x Strap c/w Clips
• 2 x Wheels
• 4 x Wheel Washers
• 2 x Bottle Chain

Fitting the wheels

• Lay the trolley frame down with the handle pointing up. Fit the axle through the chassis. Figs 1 & 2
• Fit Washers, Wheel & split pin. Figs 3, 4, 5 & 6:-
• Repeat for the other side of the axle.

Fitting the retaining strap:

• Follow steps in Figs 7, 8, 9, 10, 11, 12 & 13:

Fitting the chain:

• Fit the chain as shown in Figs 14 & 15:
• Adjust to suit your bottle size.
• Please dispose of the packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place it into the appropriate recycling bin.
• Never dispose of electrical equipment or batteries in your domestic waste. If your supplier offers a disposal facility please use it or alternatively use a recognised recycling agent. This will allow the recycling of raw materials and help protect the environment.
• SIP Industrial Products Limited Gelders Hall Road
• Shepshed
• Loughborough
• Leicestershire
• LE12 9NH
• United Kingdom
• FOR HELP OR ADVICE ON THIS PRODUCT PLEASE CONTACT YOUR DISTRIBUTOR OR SIP DIRECTLY ON:
• TEL: 01509 500400
• EMAIL: sales@sip-group.com or technical@sip-group.com www.sip-group.com

Documents / Resources

| sip 05719 Welding Trolley [pdf] User Manual
05719 Welding Trolley, 05719, Welding Trolley, Trolley
---|---

References

• Group Publishing
• SIP Industrial Products Official Website - SIP Industrial Products Official Website

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>