tuya C15B Smart WiFi Security Camera User Manual

tuya C15B Smart WiFi Security Camera User Manual

1.Product Introduction

Packing 11st: Smart Camera x 1, Manual x 1, USB Power Cord , 1, Power Adapter x 1,Screw Accessories Package x 4

Basic Parameters

Product Name: Smart Camera
Pixel: 2 .0MP/3.0MP 16.0MP
Video Compression: H .265 High Profile
Image Enhancement: Digital Wide Dynamic 30 Noise Reduction
Local Storage: Micro TF card
Wireless Encryption: WEP/WPAJWPA2 Encryption
Power Input: 12V 1A(Mln)
Total Power Consumption: SW (Max)
Wireless Standard: 2 .4G 802.11 blgln
Support Platform: AndroidOS

Component Description:
Reset Button: Long press •reset” hole 5sec, reset success.

It Is recommended to lnsert8-128GB high-speed Micro TF card, otherwise it will not be able to store. view historical video and support Important
functions such as firmware upgrading.

2.lnstall APP

Download APP· scan the QR code below to download and install.
Register and login: open the • TuyaSmart” APP to register and login according to the prompts.

https://smartapp.tuya.com/tuyasmart

2.1, Add The Device-Scan QR code mode

• Make sure Wi-Fi Is available and connected to the Internet.
• Connect the camera to the power, then system start-up completed
• Open “TuyaSmart” APP. press the’+’ in the upper night comer of the main screen (Figure 01 ); choose “Camera& Lock·. click “Smart Camera” (Figure 02) lo add camera; and then click “Next step” (Figure 03):

• If the mobile phone is not connected to wi-fi, please click “Connect to W1-fi” (Figure 04 );
• It will Jump to the WLAN interface and connects Wi-Fi (Figure 05).Please note that only 2.4 GH Wi-Fi network is supported;
• If the phone Is connected to Wi-Fi (Figure 06),

• click “Confirm”. It will jump to The interface lo prompt to scan the QR code with camera and click “Continue” (Figure. 07);
• A OR code will prompt on your screen and you need to scan it with the Smart Camera. (the camera is about 20-30 cm away from the mobile phone tens). Then click “hear the prompt sound” (Figure. 08)
• “connecting• (Figure_ 09);

• When the progress reaches 100%,connection completed(Figure 10), and click “Finish”;
• Then Jump to preview interface (Figure 11)
• After closing the device preview interface, the Interface returns to the APP home page. At this time, the connected device will appear on the APP home page (Figure 12). Then you can click dickey to the device Interface to see the mentioning situation without re-adding afterwards.

2 2, Add The Device- AP Mode

If you want to use AP Mode, press the reset button on the machine

• Make sure Wi-Fi is available and connected to the Internet.
• Connect the camera to the power, system start-up completed.
• Open “TuyaSmart” APP, press the’+’ in the upper right corner of the main screen (Figure 13); choose ·camera& Lock·. click “Smart Camera” (Figure 14) to add camera : choose “other ways” to add (as shown in Figure 15);

Note ; Before using the “AP Mode”, you need to switch to “AP Mode” by ligl1Uy pressing the “Reset key” of the device

• Then click “hot spot configuration” (Figure 16;
• Then click” oompat1billty mode”, clicks “Next” (Figure 17):
• Then click “change Network” (Figure 18);

• Then enter the password to complete the connection (Figure 19):
• Click Back and return to the APP compatible mode Interface, where the Wi-Fi name and the connected Wi-Fi name are displayed Password, check the “Confirm” button (Figure 20);
• The page jumps to where the interface prompts “Wi-Fi” to connect to the device hotspot and clicks “Connect” (Figure 21)

• The interface jumps to the WALN connection Interface, finds the Wi-Fi at the beginning of “Smart L1fi”, and clicks on the connection (Figure 22):
• When the connection is completed, click back and return to the APP interface, at which time the APP display device is connected (Figure 23).
• At this time. the device has been successfully connected: the interface Jumps to “Add Device Success rut· (Figure 24 );

• Then click “connected”, ii will jump to the Preview interface of the Device (Figure 25)
• Close the device preview interface and the interface returns to the APP home page, at which point the connected device will appear on the APP home page.(Fig. 26), After entering the device interface to view. no need to re-add, click directly Into the device Interface to view .

3.APP Video Browsing Details

1. Preview mode
2. Monitor Switch
3. About device
4. SQ
5. Full screen

4.Matters Need Attention

Try to keep away from the metal space. Avoid the furniture , microwave oven blocked; Enter Wi-Fi Password Avoid the space where the audio, video and data lunes are wound . and keep the space away from them as large as possible, Ensure that as close as possible to the coverage of wireless Wi-Fi
signals. Switching network environment: In the new network environment, please press the reset hole about 5 seconds, then connect to the- network.

The name and content of the harmful substances in the product

This product conforms to RoHS environmental protector requirements. At present, there is no mature technology in the world to replace or reduce the lead content in the electronic ceramics. porcelain, optical glass, steel and copper alloy.

Maintenance records: __ _
Maintenance time,
Fault conditions:
Fault cause,_
Troubleshooting, __ _
Return and exchange proof, ___
Date of Validity:
Original device ID, _
New device ID:
maintenance personnel signature:
Maintenance Department seal,
Maintenance voucher of intelligent
Customer:
Address:
Model: —-
Device store:
Store address:
Store contact number:
Maintenance voucher of Intelligent
Mobile:
Camera ID:.
Date of purchase:
Customer. __
Mobile: ___
Address: ____
Model: Camera ID:_
Device store:_ Date of purchase:
Store address: ____
Store contact number: __

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>