PROGRESS LIGHTING P400342-009 3 Light 18 inch Brushed Nickel Convertible Chandelier Ceiling Light Instruction Manual
- June 12, 2024
- PROGRESS LIGHTING
Table of Contents
PROGRESS LIGHTING P400342-009 3 Light 18 inch Brushed Nickel Convertible
Chandelier Ceiling Light
PACKAGE CONTENTS
** HARDWARE CONTENTS (not actual size)**
THANK YOU for selecting Progress Lighting
Safety Information
Please read and understand this entire manual before attempting to
assemble, operate or install the product. CAUTION: Read instructions carefully
and turn electricity off at main circuit breaker panel before beginning
installation.
CAUTION
Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to
ensure correct branch circuit conductor.
WARNING
If any Special Control Devices are used with this fixture, follow instructions
carefully to assure full compliance with N.E.C. requirements. If there are any
questions, contact a qualified electrical contractor.
CAUTION
All glass is fragile. Use care when handling glass shades and bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To
clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that
contain alcohol.
Assembly Instructions
-
Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC) as shown. You now need to adjust the screw length according to the fixture canopy depth.
-
Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely. Lift up the fixture and pass the screws (AA) through the two mounting hole in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16″ of threads are showing. That should be enough to mount the fixture as instructed in step 5or step 10. Next, take the fixture down and go back and tighten the hex nuts (DD) up against the mounting plate (CC).You now should have the correct length of threads for mounting the fixture.
-
Equally adjust the arms by carefully turning them out from the center.
Ceiling Assembly Instructions
-
Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire.
Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.
-
Pass the screws through the two holes in the canopy. Secure the fixture (A) to the screws (AA) using the two cylinder nuts (EE). Tighten securely.
-
Attach the glass shade (B) onto the socket of fixture (A) use the socket ring (C) to secure tightly. Thread lamps (not included) into the fixture sockets. Use GO-watt MAX incandescent medium base lamps, SBCFL or SBLED. **
Hanging Assembly Instructions
** -
Remove existing canopy parts from fixture (A). Install canopy parts and chain loop(GG) into canopy (G), Secure tightly. **** NOTE
During this step, determine the hanging length of your fixture by adding or removing chain links. The electrical and ground wire may also optionally be cut to length. Do NOT cut electrical or ground wires until this length is determined. Leave AT LEAST 6 inches MINIMUM of wire past the canopy chain loop to allow for easy connections in step 9. (Chain links can be spread open with 2 pairs of pliers. Twist the split link ends in opposite directions and close by squeezing them back together.) -
Once hanging length is determined, pass wires through stem (D) , tube (E) and chain loop (F), tightening the end of short threadstem (D) to fixture (A). Attach the tube (E) onto the stem (D) and tighten chain loop (F) to stem (D) securely. Open chain link at one end of chain (FF). Attach chain (FF) to the chain loop (F). Close the chain links back together with the pliers. open the quick link (HH), attach the other end of chain (FF) and chain loop (G) onto the quick link (HH). Close the quick link. Continue to weave the wires through the chain links (FF) and up through the canopy loop (G)
-
Strip 3/811 of insulation from the electrical wire ends. Using wire nuts (BB), connect RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire. Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.
-
Pass the screws through the two holes in the canopy (G). Secure the fixture (A) to the screws (AA) using the two cylinder nuts (EE). Tighten securely.
-
Attach the glass shade (B) onto the socket of fixture (A) use the socket ring (C) to secure tightly. Thread lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent medium base lamps, SBCFL or SBLED. ****
WARRANTY AND EXCLUSIVE REMEDY: Progress products, when properly installed and under normal conditions of use, are warranted to our customers only to be free from defects in material and workmanship at time of shipment. All warranty claims must be asserted within one year from date of purchase of the subject items; thereafter, warranty claims will not be honored. Customers’ sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or workmanship at time of shipment. Progress’s sole and maximum liability for a defective product shall never exceed the cost of the subject product. EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer’s sole and exclusive remedy against us for breach of the warranty, breach of contract or negligence or strict liability or otherwise shall be limited to repair or replacement of the subject product at our option (excluding installation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. In no case does our warranty and exclusive remedy extend to anybody other than our customers. Our customers are not authorized to extend warranties or remedies on our behalf to anyone. Such unauthorized extensions of warranties or remedies by the customer shall remain customer’s responsibility. Customer is responsible for determining the suitability of our products for customer’s use or resale, or for incorporating them into objects or for applications which customer designs, assembles, constructs or manufactures.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>