PROGRESS LIGHTING P500242-012 1 Light Satin Brass Clear Glass Transitional Pendant Instruction Manual
- June 12, 2024
- PROGRESS LIGHTING
Table of Contents
P500242-012 1 Light Satin Brass Clear Glass
Transitional Pendant
Instruction Manual P500241 P500429
1-LT SMALL PENDANT
P500242 P500430
1-LT MEDIUM PENDANT
PACKAGE CONTENTS
PART | DESCRIPTION | QUANTITY |
---|---|---|
A | Fixture | 1 |
B | Glass Shade | 1 |
C | Metal Top Cap | 1 |
D | Coupling | 1 |
E | Black Fiberglass Sleeving | 1 |
HARDWARE CONTENTS (not actual size)
**** Safety Information
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main
circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified
electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture,
follow instructions carefully to assure full compliance with N.E.C.
requirements. If there are any questions, contact a qualified electrical
contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and
bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
-
Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC) as shown. You now need to adjust the screw length according to the fixture canopy depth.
-
Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.
Lift up the fixture and pass the screws (AA) through the two mounting hole in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16″ of threads are showing. That should be enough to mount the fixture as instructed in step 4.
Next, take the fixture down and go back and tighten the hex nuts (DD) up against the mounting strap (CC). You now should have the correct length of threads for mounting the fixture. -
Attach the glass shade (B) and metal top cap (C) to fixture (A). Use the coupling (D) to secure tightly. NOTE: During this step, determine the hanging length of your fixture by adding or removing stems. The electrical and ground wire may also optionally be cut to length.
Do NOT cut electrical or ground wires until this length is determined. Leave AT LEAST 6 inches MINIMUM of wire past the canopy (JJ) to allow for easy connections in step 6. -
Pass the wires through the 6″ pipe (GG)/nipple (HH)/four 12″ pipe (FF) to achieve overall desired length. After determining overall length, attach the assembled pipes (GG) onto the fixture. Secure them tightly.Pass the wires through the black fiberglass sleeving (E), the swivel and the canopy (JJ). The black fiberglass sleeving (E) should be inside the swivel to keep wires from fraying. Next attach the canopy onto the pipe (FF) and secure tightly.
-
Strip 3/8” of insulation from the electrical wire ends. Using wire nuts (BB), connect RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire.
Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box. -
Pass the screws through the two holes in the canopy (1J). Secure the canopy (JJ) to the screws (AA) using the two cylinder nuts (EE). Tighten securely.
-
Thread the lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent medium base lamp, SBCFL or SBLED.
WARRANTY AND EXCLUSIVE REMEDY:
Progress products, when properly installed and under normal conditions of se,
are warranted to our customers only to be free from defects in material and
workmanship at time of shipment. All warranty claims must be asserted within
one year from date of purchase of the subject items; thereafter, warranty
claims will not be honored. Customers’ sole remedy for a warranty claim or
otherwise shall be limited to repair or replacement of the subject product i
it is shown to have been defective in material or workmanship at time of
shipment. Progress’s sole and maximun liability for a defective product shall
never exceed the cost of the subject product. EXCEPT FOR SUCH A WARRANTY AND
EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS.
WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR
IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO
CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR
ANY DAMAGES, WHETHER INCIDENTAL OR ‘CONSEQUENTIAL, WHICH ARE ALLEGED TO BE
CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE
SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer’s sole and exclusive
remedy against us for breach of the warranty, breach of contract or negligence
or strict liability or otherwise shall be limited to repair or replacement of
the subject product at our option (excluding installation and removal charges
which shall not be our liability) or, if we choose, refund of the purchase
price. In no case does our warranty and exclusive remedy extend to anybody
other than our customers. Our customers are not authorized to extend
warranties or remedies on our behalf to anyone. Such unauthorized extensions
of warranties or remedies by the customer shall remain customer’s
responsibility. Customer is responsible for determining the suitabiliy of our
products for customer’s use or resale, or for incorporating them into objects
or for applications which customer designs, assembles, constructs or
manufactures.
THANK YOU for selecting Progress Lighting
We can assist you with questions regarding product information, assembly or
missing parts
800-447-0573
8am-8pm (Eastern), Monday-Friday
customerservice@progresslighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>