DNAKE E217 Indoor Monitor User Guide

DNAKE E217 Indoor Monitor

REMARK
Please follow the user manual for correct installation and testing. If there is any doubt please call our tech-supporting and customer center. Our company applies itself to the reformation and innovation of our products. No extra notice for any change. The illustration shown here is only for reference. If there is any difference, please take the actual product as the standard. The product and batteries must be handled separately from household waste. When the product reaches the end of service life and needs to be discarded, please contact the local administrative department and put it in the designated collection points in order to avoid the damage to the environment and human health caused by any disposal. We encourage recycling and reusing material resources.

For specific operation instructions, please scan the following QR code to obtain the full version of the User Manual.

PACKAGE CONTENTS

Please make sure the package contains the following items:

PICTURES

MODEL: E217

SYSTEM CONFIGURATION

MODEL: E217

SYSTEM DIAGRAM

Network/POE
Connect with door station, indoor monitor or other network equipment by network switch. When indoor monitor has PoE function, the interface can supply power by connecting with a PoE network switch. If the network interface has 12V power supply, pin No. 4 and No. 5 of the RJ45 interface should connect with +12V of power interface, and pin No. 7 and 8 should connect with GND of power interface.

Power
Power input interface: connect with 12V power adapter.

Relay Output
Connect to the lock module(independent power supply is necessary for the lock).

RS485
Connect with RS485 interface device; RS485 interface can output 12V /lOOmA power supply. If RS485 equipment to be connected doesn’t require the power supply, no need to connect +12V.

Siren/ Alarm
Interface of alarm zones connects with normally-open or normally-closed switch. When the alarm zone is triggered, it will output 12V/100mA power.

INSTALLATION

MODEL: E217(Wall installation)

Product size , 195xl30xl4.Smm

Installation Instructions

[Suggestion]: The camera should be 1450~ 1550mm above the ground. The camera at this height can capture human face perfectly.

• Assemble the hooks on two sides of the bracket into the groove on the rear cover.
• Align the edge of the silica gel pad with the lower edge of the casing, and paste the pad.

SAFETY INSTRUCTIONS

In order to protect you and others from harm or your device from damage, please read the following information before using the device. Do not install the device in the following places:

• Do not install the device in a high-temperature and moist environment or an area close to a magnetic field, such as the electric generator, transformer or magnet.
• Do not place the device near the heating products such as the electric heater or the fluid container.
• Do not place the device in the sun or near the heat source, which might cause discoloration or deformation of the device.
• Do not install the device in an unstable position to avoid property losses or personal injury caused by the falling of the device.

Guard against electric shock, fire, and explosion:

• Do not use a damaged power cord, plug or loose outlet.
• Do not touch the power cord with a wet hand or unplug the power cord by pulling it.
• Do not bend or damage the power cord.
• Do not touch the device with a wet hand.
• Do not make the power supply slip or cause an impact.
• Do not use the power supply without the manufacturer’s approval.
• Do not have the liquids such as water go into the device.

Clean Device Surface

• Clean the device surfaces with soft cloth dipped in some water, and then rub the surface with dry cloth.

Other Tips

• In order to prevent damage to the paint layer or the case, please do not expose the device to chemical products, such as diluent, gasoline, alcohol, insect-resist agents, opac1fying agent and insecticide.
• Do not knock on the device with hard objects.
• Do not press the screen surface. Overexertion might cause flop over or damage to the device.
• Please be careful when standing up from the area under the device.
• Do not disassemble, repair or modify the device at your own discretion.
• The arbitrary modification is not covered under warranty. When any repair is required, please contact the customer service center.
• If there is abnormal sound, smell or fume in the device, please unplug the power cord immediately and contact the customer service center.
• When the device isn’t used for a long time, the adaptor and memory card can be removed and placed in dry environment.
• When moving, please hand over the manual to the new tenant for proper usage of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>