home8 PIR1301 Infrared Motion Sensor User Manual
- June 12, 2024
- Home8
Table of Contents
home8 PIR1301 Infrared Motion Sensor
Introduction
This Motion Sensor is designed to be used for indoor motion detection. When mounted properly, it can monitor large and open areas, such as main entrance, living room, and family room. When it detects motion, it will transmit a signal back to our Shuttle / cloud so that user can get real-time notification / alert about motion.
Key features and specifications
- RF Center Frequency: 433.92MHz
- Operating Range: Up to 100 feet (line of sight)
- Operating Temperature : 5°F to 104°F (-15°C to 40°C)
- Battery: Panasonic CR123A non-rechargeable battery
System Requirement
- This section explains the system requirement.
- Network: Proprietary 433MHz RF protocol, must co-work with Home8 OPU2/OPU3 Shuttle
Hardware Overview
- This section provides an overview of the PIR sensor.
Chapter 3. Sensor Installation & Add/Remove/Rename Sensor
Sensor installation
- Release cover tab to open the cover
- Insert CR123A battery, and put the cover back (Please make sure the battery polarity before inserting.)
- Sensor takes around 10 seconds to warm up, and LED will blink 7 times during sensor warm up
- Recommended sensor detect range, pattern, angle, and installation height:
Adding the Sensor to the System
Before you begin using the sensor, it will need to be added to the system first. To activate the sensor with the Security Shuttle, complete the following steps.
Note
- Make sure the Security Shuttle is powered on and connected to your router.
- We recommend NOT to install the battery before the sensor is successfully activated to avoid false alarm during pairing
- Tap the menu icon to show the sidebar menu.
- Tap “Device Management”. If you have more than one Security Shuttle, you may need to swipe left more than once to find the one you wish the sensor to connect to. After selecting the Security Shuttle, tap the plus icon “+” located to the right of “Sensor List”
- Select “Sensor”.
- Follow the on-screen instructions. When finished, press “Next”.
- After scanning the QR code located on the bottom of the sensor, the “sensor adding” process will begin. The process will take approximately 1 to 2 minutes.
- When the activation is completed, the sensor will be added to the device management page. In the illustration shown below, the name of the Security Shuttle is “Location1” and the name of the sensor is “Motion Sensor 488D8xxxx”.
Positioning & Installing Sensor
After the “sensor adding” process has been completed, you can place the device at the desired location. For the best performance we recommend to face the sensor towards an open area, and place the sensor at least 2 meters above the ground. For a detailed installing guide, please refer to the picture below:
Note
Keep lens and sensor as clean as possible for best sensor performance.
Remove Sensor from System
If you want to remove the sensor from the system, complete the following steps.
- Tap the menu icon to show the sidebar menu.
- Tap “Device Management”. If you have more than one Security Shuttle, you may need to swipe left more than once to find the one you wish the sensor to connect to. After selecting the Security Shuttle, select the desired sensor you want to remove by tapping “>”.
- Tap “Remove Sensor”, the app will ask for confirmation if you really want to remove the sensor. Simply tap “Yes” to confirm & remove.
Rename Sensor from System
If you want to the rename sensor from the system, complete the following
steps.
- Tap the menu icon to show the sidebar menu.
- Tap “Device Management”. If you have more than one Security Shuttle, you may need to swipe left more than once to find the one you wish the sensor to connect to. After selecting the Security Shuttle, select the desired sensor you want to rename by tapping “>”.
- Tap “>” to rename the sensor that will be shown on the app, and tap “V” to complete.
Chapter 4. Sensor Operation
Sensor operation modes, and way to judge valid motion trigger
- The sensor has 2 different modes, which are “Test Mode” and “Normal Mode”.
- For a detailed description behavior about these 2 modes, please refer to the following table.
Mode| How to enter?| Condition of valid motion alert| LED
behavior
---|---|---|---
Test Mode| The first hour after the battery is installed properly|
Please refer to fig. 1| Blinks when motion alert is valid
Normal Mode| After the Test mode is finished| Please refer to fig. 2 &
Fig. 3| Blinks when motion alert is valid
Illustration when multiple motions are detected during 3-minute countdown window under “Normal Mode”
When valid motion alert happens
When valid motion alert happens, the LED indicator on the sensor will blink
one time, and your app will also pop out a notification to indicate there’s a
motion alert as below.
Low battery alert
This sensor can automatically detect current battery status, and report “low
battery” when battery level is too low. When “low battery” happens, the LED
indicator on the sensor will blink constantly, and the app will also show “low
battery alert from sensor” notification as below:
Device detachment detection
This sensor has a built-in tamper switch to detect front cover status. When
the front cover is open, LED indicator will blink 1 time, and app will also
show a “Device detachment detected” notification as below.
Appendix – Glossary of Terms
-
Arm: The cameras and other security related sensors in the system are actively monitoring the surroundings. Any suspicious activity that has been detected by the camera or sensor will prompt the app to immediately send a notification. A recording will also be performed by the camera(s) that witnessed the event.
-
Disarm: The cameras and other security related sensors in the system are no longer actively monitoring the surroundings. The system will not react to any suspicious activity detected by these devices. No notification will be sent.
Note: If the continuous recording function is turned on, video recording will always work regardless if the system is armed or disarmed. For more details regarding the continuous recording function, see Section 6.8 Turn On/Off Continuous Recording. -
Event: An event is created when any camera or sensor detects activity or is manually triggered by the user.
-
Security Shuttle: Functions as a secure and intelligent hub to manage the devices and communicate with the cloud server. Currently, there are three types – OPU1120, OPU2120, and OPU3120.
home8alarm.com. 1-844-800-6482 | support@home8alarm.com.
References
- More Security for Less | home8 Pro Security & Safety Systems
- More Security for Less | home8 Pro Security & Safety Systems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>