ROCKET RC TS80 Sensored Brushless ESC Instruction Manual
- June 12, 2024
- ROCKET RC
Table of Contents
TS80 Sensored Brushless ESC
INSTRUCTION MANUAL
DECLARATION
This is Electronic Speed Controller (ESC) for car. High power system for RC model is very dangerous, so please read this manual carefully. Since we can’t control over the correct use, installation, application, or maintenance of our products, we’ve no liability shall be assumed nor accepted for any damages, losses or costs resulting from the use of the product. Any claims arising from the operating, failure of malfunctioning etc. will be denied. We assume no liability for personal injury, consequential damages resulting from our product or our workmanship.
SPECIFICATION
• 8 bit processor • Low resistance FET • Continuous current
Forward/Brake/Reverse: Yes (Factory preset at Forward/Brake)
Dimensions: 29.50(L) x29.52(W) x 24(H)mm(including fan)
Weight: 61.4g(including wires)
Voltage Input: 6V-11V
Peak Current: 160A
Continuous current: 80A
Motor Limit: Over 13.5Turns(540)/10.5Turns(380/390)
Motor Type: Sensored 380/390/540 brushless motors
B.E.C.: 3A/6V
Multi Protection System: Yes
INSTALLATION & CONNECTORS
RADIO& ESC SETUP
Transmitter Settings:
- Throttle Travel Maximum / 100%
- Brake Travel Maximum / 100%
- Throttle Exponential Start with 0%
- Throttle Neutral Trim Center/ 0
- Throttle Servo Reverse (Futaba, KO, Sanwa)
The initial set-up of the throttle end-points of the ESC:
- Connect the power wires of the ESC to a fully charged
- Bind your receiver and transmitter first if your radio requires you to do so.
- Use a 1.5mm screw press and hold the ESC set button and then switch on the ESC, release the button unit the led change to blue and flash from red, you can listen to two beeps sound from motor at the same time.
- Keep the throttle in the neutral position and then press the set button, the neutral position already memory on ESC when listen to a beep sound.
- Full throttle and then press once the set button, the maximum throttle position already memory on ESC when listen for two beeps sounds.
- Full brake and then press once the set button, the maximum brake position already memory on ESC when listen for three beeps sounds.
- A beep will then sound, Signifying that the ESC endpoints have been successful.
CUSTOMIZING THE ESC
To begin, connect the battery wires to a charged battery, then connect the BEC
wire 3pin wire to the program card “S+-“port ( 3pin port). Turn on the ESC and
the Program Card will read the esc setup once time, activate automatically.
You can now begin programming your ESC.
TIPS! Program card is done using the 4 buttons below on the led, The function
of each button start from right hand side are ITEM, VALUE, OK and RESET.
“ITEM” button go to next item to select.
“VALUE” button go to next value select.
” OK” button go to confirm your select.
” RESET” button go back to factory setup.
Program Manual
| Item/Value Item | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |
|---|---|---|---|---|---|---|---|---|---|
| 1.Low Voltage Cut-off | 3.1V Slow | 2.9V Slow | 2.7V Slow | Disable | 3.4V Slow | ||||
| 3.1V Stop | 2.9V Stop | 2.7V Stop | 3.4V Stop | ||||||
| 2.Start Mode(Pundi) | Level3 | Leven | Level6 | Level2 | Level4 | Level5 | |||
| 3.Max. Brake Force | 50% | 25% | 75% | 100% | Disable | ||||
| 4.Max. Reverse Force | 25% | 50% | 75% | 100% | |||||
| 5.Neutral Range | 9% | 6% | |||||||
| (Normal) | 12% (Wide) |
(narrow)
6.Motor Overheat Protection| 120 Stop| 135 Stop| 150 Stop| 120 Slow| 135 Slow|
150 Slow| Disable| |
7.FSC Overheat Protection| 105 Stop| 95 Stop| 105 Slow| 95 Slow| Disable| | |
|
8.Running Mode| Forward/| Forward/
Brake| Forward/ Reverse| | | | | |
FS
Brake
9.Drag Brake Force| 0%| 5%| 10%| 20%| 30%| | | |
10.Timing OFF| Off| 10| 20| 30| 40| | | |
11.Turbo Timing| Off| 10| 20| 30| 40| 50| 60| |
12.PWM Frequency| 8K| 2K| 4K| 12K| 16K| 24K| | |
13.Brake PWM Frequency| 1KHz| 400Hz| 600Hz| 800Hz| 2K| 4k| | |
Shenzhen Surpass Tech co., Ltd
http://www.surpass-hobby.com
Tel: +86-0755-89322901
11024-1077-06
http://www.surpass-hobby.com