RUIJie EST310V2 5GHz Dual-stream 802.11ac 1KM Wireless Bridge User Manual

RUIJie EST310V2 5GHz Dual-stream 802.11ac 1KM Wireless Bridge

Product Information

The product is a multi-function device designed to perform various tasks. It features a compact design and user-friendly interface. The device is equipped with advanced technology to ensure optimal performance and efficiency.

Product Usage Instructions

1. Before using the product, make sure it is properly connected to a power source and any necessary peripherals are attached.
2. Refer to the user manual for specific instructions on how to set up the product.
3. To power on the device, press the button labeled “Power” or follow the instructions provided in the manual.
4. Once powered on, the product will display a menu of options on the screen. Use the provided controls or buttons to navigate through the menu.
5. Select the desired function or task from the menu by highlighting it and pressing the “Select” button.
6. Follow any additional on-screen instructions or prompts to complete the selected task.
7. If necessary, refer to the user manual for troubleshooting tips or further assistance.
8. To power off the device, press and hold the “Power” button until the screen turns off.
9. When not in use, it is recommended to disconnect the device from the power source and store it in a safe place.

Please note that these instructions are a general guide. For specific information about each function or task, refer to the user manual provided with the product.

Product Manual

Note
The device and software will be upgraded constantly. Please contact Ruijie technical support for details.

Parts List

Management software WSP-EST310 V2 has been installed on the device.

Networking

LED & Ports

1. LED Description

   • System LED
     Blinking Green: The device is being booted.
     Solid Green: The device is working properly.

   • LAN LED
     Off: No cable is connected.
     Blinking Green: Link is up. The port is sending or receiving data.
     Solid Green: Link is up. The port is not sending or receiving data.

   • Signal LED
     Off: No signal is detected.
     Blinking: The signal is weak.
     Solid: The stronger the signal gets, the more LEDs light up.

2. 12V DC Power Port
   Inner Diameter: 2.1mm. Outer Diameter: 5.5mm.

3. LAN/PoE Port

4. Reset Button

Cable Connection

Video Recorder End

PoE Max Distance: 1 00m (CATS/6/7 Cable)

Camera End

PoE Max Distance: 1 00m (CAT5/6/7 Cable)

Mounting the Device

Pole Mounting

1. Secure the mounting bracket to the pole by threading two clamps through the mounting bracket.
2. Install the device to the mounting bracket.

Wall Mounting

1. Secure the mounting bracket on the wall.
2. Install the device to the mounting bracket.

Bridging Management
The wireless bridges are used in pairs without extra configuration. If you want to manage the bridge or view data, both App management and Web management are available.
App Management (Recommended)

1. Scan the QR code on the manual or device to download Ruijie Cloud App.
2. Sign up an account and log in with it.
3. Navigate to Project>+in the upper right corner > Wireless Bridge to manage the device.

Web Management

Wireless Login (Recommended)

1. Connect to the 5G SSID of the bridge (Default: @Ruijie-bxxxx.
   xxxx indicates the last four digits of the MAC address).

2. Open a browser window, enter http://192.168.120.1 into the address bar and press Enter.

Wired Login

1. Set the IP address on your computer.
   IP Address: 10.44.77.100
   Subnet Mask: 255.255.255.0
   Gateway: 10.44.77.254

2. Open a browser window, enter http://10.44.77.254 into the address bar and press Enter.

One-to-Many Settings

Select Master Bridge
the Select device. any video recorder end as the master bridge and power on Select Slave Bridge
Select any other bridge device and take (either the video following recorder steps end to or configure camera the end) as slave the bridge.slave

Configure Slave Bridge

1. Log into the Web management page.

2. Select Pair Again in the upper right corner.

3. Click Start.
   

4. 5. Select Camera (CPE) and click Next.

5. Click Scan and select an SSID from the dropdown list or enter an SSID (Example: @Ruijie-wds-xxxx. xxxx indicates the last four digits of the MAC address).

6. Click Submit.

7. The Mode LED on the video recorder end is solid on and the Mode LED on the camera end blinks at 0.5 Hz.

8. If you want to add camera ends, please take the above steps again.

Notes

1. Please make sure that there are no obstacles between both ends.
2. If there are obstacles, please make sure that the devices are installed 3 to 5 meters higher than the obstacles.
3. If the obstacles cannot be avoided, it is recommended to adopt the repeater solution to implement Back-to-Back WDS.
4. For data transmission over a super-long distance, it is recommended to adopt the repeater solution to reduce distance between each pairing devices and improve stability.
5. If the monitoring devices and peer ends are concentrated at one location, it is recommended to select the one-to-many solution to reduce cost and improve efficiency.
6. Please make sure that the distance between both ends are over 2 meters.
7. The Mode LED on the video recorder end is solid on and the Mode LED on the camera end blinks at 0.5 Hz.
8. The device may cause radio interference in living environment.
   Please take measures to reduce interference.

Note:
Hong Kong.
This equipment is restricted to indoor operation in 5.15-5.25GHz for

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>