NYQUIST NQ-E7020 Digital Call Switch User Manual
- June 4, 2024
- NYQUIST
Table of Contents
User Manual
NQ-E7020 Digital Call Switch
Digital Call Switch – Normal/Emergency Calls
The Nyquist Digital Call Switch (DCS) (NQ-E7020) is a wall-mounted, touch-
activated call-in device that, when associated with a call-back speaker,
allows you to initiate a Normal or Emergency call from classrooms or other
staff locations via an associated Nyquist intercom speaker.
The switch includes a capacitive touch interface or Touch Sensor, and a full
spectrum color light emitting diode (LED) status ring. The LED status ring has
three segments that illuminate. Use the touch interface to initiate a call or
action and use the LED status ring to visually confirm actions and status. For
example, a solid blue LED indicates that the DCS is receiving power and is in
Normal standby status.
The Admin Station answers the calls received according to which calls have the
higher priority level. Emergency calls are answered first, bumping Normal or
Urgent calls down
further in the queue.
Placing a Normal Call
To place a Normal Call:
-
Touch the DCS’s Touch Sensor one time.
One segment of the LED status ring illuminates solid green. If the DCS isn’t touched again within 3 seconds, all three LED status ring segments flash green and a Normal call is placed to the Admin Station. Note that you can escalate the call to an Emergency Call by touching the DCS’s Touch Sensor one more time. The three LED status rings illuminate solid green when the Admin Station answers the call. -
Begin talking toward the speaker.
The LED status ring segments illuminate solid blue after the call ends. segments
Placing an Emergency Call
To place an Emergency Call:
-
Touch the DCS’s Touch Sensor three times.
One segment of the LED status ring illuminates solid green. A second touch made within 3 seconds results in two LED status ring segments illuminating green. When a third touch is made within 3 seconds after the first touch, all three of the LED status ring segments flash red to indicate that an Emergency call is being made. The three LED status ring segments illuminate solid red when the Admin Station answers the call. -
Begin talking toward the speaker.
The LED status ring segments illuminate solid blue after the call ends.
NOTE: You can escalate an unanswered Normal call to an Emergency call by touching the DCS’s Touch Sensor one more time.
Using Privacy Mode
In addition to placing calls to the Admin Station, the DCS can be used to
enable or disable Privacy Mode.
NOTE: Spy Mode monitoring cannot be used on a station that has been set
to Privacy Mode.
Privacy Mode, when allowed by a system administrator and enabled at the DCS,
disables the talkback path of the classroom Voice over Internet (VoIP)
speaker. If an intercom call is placed to the classroom, it remains a one-way
transmission until Privacy Mode is disabled.
To enable Privacy Mode:
Touch and hold the DCS’s Touch Sensor for four seconds.
Two seconds after you touch the DCS’s Touch Sensor, one LED status ring
segment illuminates purple. A second LED status ring segment illuminates
purple a second later, and the third illuminates purple a second later. The
three LED status ring segments continue to illuminate purple until the Privacy
Mode is disabled.
If you disable Privacy Mode, the classroom speaker can be used for two-way
communications and to monitor classroom activities.
To disable Privacy Mode during an intercom call:
Touch the DCS’s Touch Sensor one time.
The LED ring segments illuminate green to indicate that Privacy Mode is
disabled.
To disable Privacy Mode outside of an intercom call:
Touch and hold for four seconds the DCS’s Touch Sensor.
Two seconds after you touch the DCS, the LED status ring segments begin
turning off one at a time. Four seconds after you touch the DCS, the LED
status ring segments illuminate blue to indicate that the DCS is in normal
mode.
2018 Bogen Communications Inc.
Digital Call Switch – Normal/Emergency Calls
All rights reserved
740-00019C
1811
Documents / Resources
|
NYQUIST NQ-E7020 Digital Call
Switch
[pdf] User Manual
NQ-E7020 Digital Call Switch, NQ-E7020, Digital Call Switch, Call Switch,
Switch
---|---