Pattfield PE-ARM 40 V Battery Lawn Mower Instruction Manual
- June 12, 2024
- Pattfield
Table of Contents
- Scope of delivery
- Table of content
- Symbols
- Safety Instructions
- MAINTENANCE AND STORAGE
- ADDITIONAL SAFETY INSTRUCTIONS ON RISKS DUE TO VIBRATION
- FOR USE OF BATTERIES
- Product overview
- Intended use
- Using the appliance
- Adjustments
- Technical Data
- Noise & Vibration
- Care & Maintenance
- Replacement parts
- Troubleshooting
- Troubleshooting
- Declaration of conformity
- Disposal
- Documents / Resources
**Pattfield PE-ARM 40 V Battery Lawn Mower Instruction Manual
**
Thank you!
We are convinced that this appliance will exceed your expectations and wish you joy while using it.
Please read this user manual completely and observe the safety instructions.
Scope of delivery
1x Mower unit
1x Collection bag
2x Lower handle bar
4x Locking lever, screw, washer
1x Charger
2x Battery
If any parts are missing or damaged, please contact your HORNBACH Store.
Table of content
Scope of delivery 131
Symbols 132
Safety Instructions 133
Product overview 137
Intended use 137
Adjustments 137
Using the appliance 137
Technical Data 140
Noise & Vibration 141
Care & Maintenance 141
Replacement parts 141
Troubleshooting 142
Declaration of conformity 143
Disposal 144
Symbols
Please read this user manual carefullyand keep it for further reference.
Warning of accident and injury to persons and serious damage to property
Wear safety glasses for protection of your eyes.
Wear hearing protection for protection of your ears.
Wear dust mask for protection of your respiratory tract
Wear protective gloves for protection of your hands.
Wear protective boots for protection of your feet.
Use only batteries which are charged to the same level.
Blade continues to rotate after the machine has been switched off. Wait until
all machine components have come to a complete stop, before touching them.
Do not use the machine in wet or humid conditions. Danger of electric shock!
Attention! Read the instruction manual, prior to use.
Keep bystanders away. Attention! Sharp cutting blades. Prior to maintenance
or care, remove the battery and pull out the safety plug.
Guaranteed sound power level.
WARNING: The lawnmower shall not be operated without either the entire grass catcher or the guard in place.
Safety Instructions
IMPORTANT
READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE
Safe operating practices for electrically powered lawnmowers
GENERAL
a) This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
b) Children should be supervised to ensure that they do not play with the
appliance.
c) Only use the product in the manner for the functions described in this
user manual.
d) Never operate the appliance when you are tired, ill or under the
influence of alcohol, drugs or medicine.
e) The appliance is only to be used with the power supply unit provided
with the appliance.
TRAINING
a) Read the instructions carefully. Be familiar with the controls and the
correct use of the machine.
b) Never allow children or people unfamiliar with these instructions to
use the machine. Local regulations can restrict the age of the operator.
c) Never operate the machine while people, especially children, or pets
are nearby.
d) Keep in mind that the operator or user is responsible for ac cidents
or hazards occurring to other people or their property.
PREPARATION
a) While operating the machine always wear substantial footwear and long
trousers. Do not operate the machine when barefoot or wearing open sandals.
Avoid wearing clothing that is loose fitting or that has hanging cords or
ties.
b) Thoroughly inspect the area where the machine is to be used and remove
all objects which can be thrown by the machine.
c) Before using, always visually inspect to see that the blade, the blade
bolt and the blade assembly are not worn or damaged. Replace worn or damaged
components in sets to preserve balance. Replace damaged or unreadable labels.
d) Warning: the lawnmower shall not be operated without either the
entire grass catcher or the guard in place.
OPERATION
a) Operate the machine only in daylight or in good artificial light.
b) Avoid operating the machine in wet grass.
c) Always be sure of your footing on slopes.
d) Walk, never run.
e) Mow across the face of slopes, never up and down.
f) Exercise extreme caution when changing direction on slopes.
g) Do not mow excessively steep slopes.
h) Use extreme caution when reversing or pulling the machine towards you.
Stop the blade(s) if the machine has to be tilted for transportation when
crossing surfaces other than grass, and when transporting the machine to and
from the area to be used.
j) Never operate the machine with defective guards or shields, or without
safety devices, for example deflectors and/or grass collector, in place.
k) Switch on the motor carefully according to instructions and with feet
well away from the blade(s).
l) Do not tilt the machine when switching on the motor, except if the
machine has to be tilted for starting. In this case, do not tilt it more than
absolutely necessary and lift only the part, which is away from the operator.
m) Do not start the machine when standing in front of the discharge
opening.
n) Do not put hands or feet near or under rotating parts. Keep clear of
the discharge opening at all times.
o) Do not transport the machine while the motor is running.
p) Stop the machine, and remove battery packs. Make sure that all moving
parts have come to a complete stop
-
before clearing blockages or un- clogging chute,
-
before checking, cleaning or working on the machine,
-
after striking a foreign object. In- spect the machine for damage and make repairs before restarting and operating the machine. If the machine starts to vibrate ab- normally (check immediately):
-
inspect for damage,
-
replace or repair any damaged parts
-
check for and tighten any loose parts.
q ) Avoid using the machine in bad weather conditions especially when there is a risk of lightning.
r) Disconnect the unit from the power supply (i.e. remove the plug from the mains, remove the disabling device or removable battery) -
whenever the unit is left unat- tended;
-
before clearing a blockage;
-
before checking, cleaning or work- ing on the unit;
-
after striking a foreign object;
-
whenever the unit starts vibrating abnormally.
MAINTENANCE AND STORAGE
a) Keep all nuts, bolts and screws tight to be sure the machine is in
safe working condition.
b) Check the grass collector frequently for wear or deterioration.
c) On machines with multi blade, take care as rotating one blade can
cause other blades to rotate
d) Be careful during adjustment of the machine to prevent entrapment of
the fingers between moving blades and fixed parts of the machine
e) Always allow the machine to cool down before storing.
f) When servicing the blades be aware that, even though the power source
is disconnected, the blades can still be moved.
g) Replace worn or damaged parts for safety. Use only genuine replacement
parts and accessories.
ADDITIONAL SAFETY INSTRUCTIONS ON RISKS DUE TO VIBRATION
a) The declared vibration data represents the main applications of the
appliance, but different uses of the appliance or poor maintenance can result
in different vibration data. This may significantly increase the vibra- tion
level over the total working pe- riod.
b) Additional safety measure shall be taken to protect the user from ef-
fects of vibration. Maintain the ap- pliance and its accessories, keep hands
warm and organize work pat- terns and periods
FOR USE OF BATTERIES
a) Do not open, dismantle, shred or short-circuit batteries. Danger of
ex- plosion.
b) Batteries (battery pack or batteries installed) shall not be exposed
to ex- cessive heat such as sunshine, fire or the like. Protect from
mechanical shock. Keep dry and clean. Keep away from children.
c) Dispose of properly. Pay attention to environmental aspects of battery
disposal. Do not dispose of in household waste.
d) Remove batteries when not using the tool for a longer period of time.
e) In case of battery leakage, remove the batteries and clean the battery
compartment thoroughly. Avoid contact with skin and eyes.
f) In case of damage and improper use of the battery, Vapours may be
emitted. Provide for fresh air and seek medical help in case of complaints.
The vapours can irritate the respiratory system.
For safety instructions for the battery charger please refer to the manual of the charger.
For safety instructions for Li-ion batteries please refer to the manual of the batteries.
Product overview
Intended use
The appliance is intended for mowing grass and lawn areas in private outdoor environment. The appliance is not intended for commercial use.
Any other use (e.g. trimming or mowing of bushes, hedges, climbing plants, roof gar – dens or balcony boxes, as well as chopping or shredding) or modification to the appliance is considered as improper use and could cause considerable dangers.
Using the appliance
Caution! Before starting to use theappliance, check the blades and fastening elements for damage. Do not use the appliance if anything is damaged.
- The appliance is equipped with a safety button
- In order to switch on the appliance, plug in and push the safety button 2 to the right and hold it, tilt the appliance backwards and lift the on/ off trigger 1 towards the handle. The safety button 2 snaps in and stays locked until the on/ off trigger 1 is released.
- Keeping the on/off trigger 1 lifted, wait until the appliance has reached full speed.
- Place both hands on the upper handle 14, return the appliance back to the ground and slowly start pushing the appliance forward.
- Start mowing in parallel lines. For a better result, repeat the process in a 90° angle.
- To switch off the appliance, release the on/ off trigger 1. Wait until the blade has come to a complete stop before proceeding with further actions.
Adjustments
-
INSTALL HANDLE
Install the lower bars 11 onto the screws on both sides. Fix with the locking levers 13 and washers.
Caution! Make sure the appliance is switched off and the batteries are removed. -
Fix the upper handle 14 on both sides with the locking levers 13, washers and screws. It can be installed in two positions.
Caution! Never use the appliance with open locking levers.
CABLE CLIPS
-
Fasten the power cable to the handle 15 with the cable clips 4.
BATTERIES -
Lift the battery cover 7 and push in two charged batteries until they click into place.
Caution! Make sure the batteries are always charged to the same level
COLLECTION BAG
-
Lift the safety flap 5 and attach the collection bag 12 to the mower. Lower the flap again.
FILLING INDICATOR -
The collection bag 12 provides a filling indicator 3
Collection bag empty: Flap floats
Collection bag full: Flap falls down
SWITCHING ON
-
In order to switch on the appliance, plug in and push the release key 2 to the right and hold it. Lift the on/ off trigger 1 towards the handle 15. The key snaps in and stays locked until the on/ off trigger is released.
-
SWITCHING OFF
To switch off the appliance, release theon/ off trigger 1. The release key 2 disengages automatically.
Caution! Wait until the blade has come to a complete stop before switching on the appliance again
CUTTING HEIGHT
- Pull out the height adjustment lever 10 and move it to the desired cutting depth.
Caution! Make sure the appliance is switched Off.
REPLACING THE BLADE
-
Loosen the fastening screw A and remove the worn blade.
-
Insert new blade with the inscription “GRASS SIDE” showing away from the motor. Tighten the fastening screw A.
Technical Data
- Type Battery lawn mower
- Nominal voltage max. 40 V (2 x 20 V)
- Max. cutting width 340 mm
- Grass bag capacity 30 litres
- Cutting heights 33 – 83 mm
- Cutting heights positions 6
- Net weight 12.4 kg
- Sound pressure level (LpA) 87 dB(A) / Uncertainty K = 3 dB(A)
- Measured sound power level (LWA) 93.7 dB(A) / Uncertainty K = 2.1 dB(A)
- Max. vibration emission (ahw) ≤ 3.6 m/s² / Uncertainty K = 1.8 m/s²
- SUITABLE BATTERIES PE-AK2 (6801240 2x included)
- PE-AK4 (6801241 optional)
- Voltage 20 V
- Capacity PE-AK2 (6801240):2.0 Ah Li-ion battery
- PE-AK4 (6801241): 4.0 Ah Li-ion battery
- SUITABLE CHARGER Double charger (included)
- Nominal voltage 100-240 V ~ 50/60 Hz, 50 W
- Output voltage 20 V 2,0 A
- Charging time 75 min for 2 x PE-AK2
- 140 min for 2 x PE-AK4
- Operation temperature 10-40 °C
- Protection Class / II
- Weight 0,2 kg
- SUITABLE CHARGER PE1H quick-charger (6801242 optional)
- Nominal voltage 100-240 V ~ 50/60 Hz, 78 W
- Output voltage 20 V , 3.0 A
- Charging time 60 min for PE-AK2
- 120 min for PE-AK4
- Operation temperature 10-40 °C
- Protection Class / II
- Weight 0.25 kg
Please observe the article number on the type plate of the appliance. The trade names of the individual appliance may vary.
Noise & Vibration
The values given in these instructions have been measured in accordance with a standardized measurement procedure specified in EN ISO 3744:1995 and ISO 11094:1991 and can be used to compare appliances. It may be used for a preliminary assessment of exposure.
Warning! The vibration emission during actual use can differ from the declared total value depending on the use of the appliance.
Care & Maintenance
Caution! Make sure the appliance is switched off and the batteries are removed.
- Always keep the appliance clean, dry andfree of oil or grease.
- Wear safety glasses and gloves to protect your eyes and hands whilst cleaning.
- For safe and proper working, always keep the machine and ventilation slots clean.
- Regularly check for obvious defects and/or damaged components.
- Periodically check all fixings. These could become loose with time due to vibration.
- Check the collection bag regularly for signs of wear.
- The most used part is the blade. Inspect the lades regularly:
- If the blade is worn or blunt, it must be replaced immediately
- If the appliance starts to vibrate excessively, the blades seem to be unbalanced and must be replaced.
- Replace any worn or damaged parts.
- If the body of the appliance needs cleaning, wipe it with a brush or a soft damp cloth. A mild detergent can be used but nothing like alcohol, petrol or similar cleaning agent.
- Never use caustic agents to clean plastic parts.
- Lubricate all moving parts at regular intervals.
- Store the battery and the appliance separately.
- Charge the battery before storing the appliance in winter.
- Store the appliance in a dry and frost-free place (10-25 °C).
Replacement parts
Please quote the following data when ordering replacement parts:
- Type of machine
- Article number of the machine
- Identification number of the machine
- Replacement part number of the part required
Troubleshooting
Caution! Make sure the appliance is switched off and the batteries are removed. Always wear protective gloves.
Troubleshooting
Problem | Possible cause | Solution |
---|---|---|
Motor does not run | Battery empty | Recharge battery |
Unsuitable cutting areas | Start on short or already mown grass. | |
Blade is blocked | Clean discharge chute and housing (blade must rotate freely) | |
Battery is not inserted correctly | Remove batteries and insert again | |
Release key is not inserted correctly | Re-insert key and push it to the right |
while lifting the on/ off trigger
Wrong cutting height| Set the wheels to the correct cutting height
Motor power drops| Wrong cutting height| Set the wheels to the correct cutting
height
Discharge chute is blocked| Clean discharge chute and housing (blade must
rotate freely)
Poor and uneven cut| Replace the blade (contact service)
Collection bag is not filled suitably| Unsuitable cutting areas| Set the
wheels to the correct cutting height
Allow lawn to dry
Poor and uneven cut| Replace the blade (contact service)
Collection bag is full| Empty the collection bag
Discharge chute is blocked| Clean discharge chute and housing (blade must
rotate freely)
If the device still does not work, please contact your local HORNBACH store or write an email to: service@hornbach.com
Declaration of conformity
We declare, that the product described in Technical Data:
manufactured for:
HORNBACH Baumarkt AG
Hornbachstraße 11
76879 Bornheim / Germany
is in conformity with the following directives:
Machinery Directive 2006/42/EC
Outdoor Directive 2000/14/EC and 2005/88/EC
EMC Directive 2014/30/EU
RoHS Directive 2011/65/EU
and in accordance to the following applicable harmonized standards:
EN 60335-1:2012+A13
EN 60335-2-77:2010
EN 62233:2008
EN 55014-1:2017
EN 55014-2:2015
The conformity with the Machinery Directive is verified by the conformity assessment procedure according to the Directive 2006/42/ EC.
The conformity with the Noise Emission of Outdoor Equipment Directive is verified by the conformity assessment procedure according to annex VI, Directive 2000/14/EC & 2005/88/EC.
Measured sound power level: 93.7 dB(A)
Guaranteed sound power level:
96 dB(A)
Notified Body:
TÜV SÜD Industrie Service GmbH Westendstrasse 199
80686 München / Germany
Notified Body No.: 0036
Cert. No.: OR/051748/001
Andreas Back
Head of Quality Management, environment & CSR
Person authorised to compile the technical file
Bornheim, der 14.06.2019
HORNBACH Baumarkt AG
Hornbachstraße 11
76879 Bornheim / Germany
Disposal
The crossed-out wheeled bin symbol requires separate disposal for waste electrical and electronic equipment (WEEE). Such equipment may contain valuable, but dangerous and hazardous substances. You are required by law to return these products to a designated collection point for the recycling of WEEE and must not under any circumstances dispose of them as unsorted municipal waste. In this way, you can help to conserve resources and protect the environment.
In Germany, HORNBACH is obliged:
- To take back old appliances of the same type free of charge in HORNBACH stores when you purchase a new electrical or electronic appliance.
- To take back up to 3 WEEE of the same type (up to max. 25 cm edge length) free of charge in HORNBACH stores, even if you do not purchase a new appliance.
- When delivering a new electrical or electronic appliance to a private household, tocollect an old appliance of the same type free of charge or to enable you to return it in your immediate vicinity.
Make sure that all batteries have been removed from the appliance before disposing of it. You will find notes on this in the operating instructions (see Chapter “ATTACH BATTERY”). For further details, please consult www.hornbach.com or your local authorities.
Used batteries and rechargeable batteries must be disposed of properly. Battery selling stores and municipal collection points offer special containers for battery disposal. Precise data on the type and chemical system of the batteries can be found in the technical data, corresponding markings on the batteries themselves.
Children must not play with plastic bags and packaging material, due to the risk of injury and suffocation. Store such material safely or dispose of it in an environmentally friendly way.
Manufactured for
HORNBACH Baumarkt AG
Hornbachstraße 11
76879 Bornheim / Germany
Documents / Resources
|
Pattfield PE-ARM 40 V Battery Lawn
Mower
[pdf] Instruction Manual
PE-ARM 40 V Battery Lawn Mower, PE-ARM, 40 V Battery Lawn Mower, Battery Lawn
Mower, Lawn Mower, Mower
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>