AIDimming PE296R 12-18W Constant Current Dimming LED Driver Owner’s Manual
- June 12, 2024
- AIDimming
Table of Contents
AIDimming PE296R 12-18W Constant Current Dimming LED Driver
Product Usage Instructions
Follow the below instructions to use the product:
- Ensure that the product is properly connected and powered on.
- Refer to the user manual for specific functions and features.
- Use the provided HDWXUHV for enhanced performance.
- For additional accessories, refer to the 3)& section.
- When using the product for KRPHOLJKWLQJDQGFRPPHUFLDOOLJKWLQJ, follow the instructions mentioned in the 6XLWDEOHIRU/(‘KRPHOLJKWLQJDQGFRPPHUFLDOOLJKWLQJ section.
- For proper installation and setup, refer to the 6DIHQRORDGSURWHFWLRQGHYLFH section.
- Make sure to read and understand the safety precautions mentioned in the user manual before using the product.
- If you require assistance or have any questions, please refer to the customer support information provided in the manual.
PE296R 12 -18W
Features
- LED phase-cut dimming driver, dimming range 2-100%
- Suitable for PC MOSFET dimmer and FC TRAIC dimmer
- Active PFC
- Protections:short circuit/over voltage/over current
- Natural cold wind
- Big terminal locked by screw
- Suitable for LED home lighting and commercial lighting
- Safe no load protection device
- Economic and convenient installation
- conform to the world lighting equipment safety standards
- Protection class II
- Three vears warranty
General description
PE296R is one of the constant current dimming LED driver developed by my company with high power factor high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.
Specification
Dimensions
Product Label
Wiring Diagram
Wiring:
- The input terminal: wire gauge 22AWG-14AWG (0.315mm2 – 2.06mm2) wire stripping requirement:9-10mm.
- The output terminal: wire gauge 22AWG-12AWG (0.315mm2 – 3. 15mm2)wire stripping requirement:6-7mm.
Compatibility:
Note : due to the different power of dimmer and dimming system, the compatibility will be different. Before purchase, it needs to confirm with the business to ensure the best matching effect of the product. The use of guidance:
Note:
- please pay attention to the distinction between input and output, connect correctly, then power on
- please connect first the load of the DC output, open the power supply after checking; in the constant current mode, if power on at an open circuit, please turn off the power supply and can’t connect the LED until the electric energy stored by the output release, or it may damage the LED;
- this type of power supply is only limited to the use of LED lamps and lanterns, the input voltage range is AC200-250V, the heat insulation cotton and other items that obstruct the heat dissipation of the product, which conforms to the product under the Specified output voltage, current range, the use environment temperature is -20-45 degrees, and the surface can not cover the conditions of the environment, this product enjoys three yearsof free warranty.
The abnormal conditions and the corresponding treatment methods:
- the LED lamp doesn’t brighten after the dimming driver is connected at the first time please turn off the AC input and check as follows:
- Whether or not DC outputs bad contact;
- Whether DC output polarity is reversed, or the LED board is welded anti;
- Whether AC input is bad contact; test after eliminating these failures.
- the device has good connection, LED lights, but the LED flicker, please turn off the AC input, then check the DC output:
- overload, under load.
- Whether or not the parameters and actual parameters match.
- please timely communicate with us if you any questions in the using, we will try our best to solve the problems with you.
Statement:
The pictures and specifications is for reference only, in kind prevail,
specifications are subject to change with further notice.