phrozen 210908 Sonic XL Desktop Resin 3D Printer Instruction Manual

phrozen 210908 Sonic XL Desktop Resin 3D Printer

Operation

• System Phrozen OS
• Operation 5 inch Touch Panel Slicer Software
• Phrozen Dental Synergy Slice Connectivity USB Ethernet I WIFI

Printing Specification

• Technology Resin 3D Printer – LCD Type
• Light Source 405nm ParaLED 3.0 Module
• XY Resolution 0.050 mm
• Layer Thickness 0.01- 030 mm
• Printing Speed 90 mm/hr
• Power Requirement AC100-240V: 50-60Hz

Hardware Specifications

• Printer Size L29 xW33x H47 cm
• Printing Volume L20 xW125 x H20 cm
• Printer Weight 22 kg

Notice: For first-time usage, please follow the user manual and follow the steps: Perform Z-axis Calibration, LCD Test, and Test Printing if you encounter any technical problems, please contact support@phrozen3d.com

PRINT Choose your 3D fileto begin printing

RESIN PROFILE To adjust your settings, click on

RESIN PROFILE Z-AXIS Followi nstructionsion the manual to calibrate the Z-axis.

LCD TEST Please follow instructions in the user manual to conduct the LCD test

WIFI Connects to Proven OS interface:

POWER BUTTON Click on SHUT DOWN. Then switch off the :. button at the back to. completely. turn off the device and avoid system damage.

SET UP

Click on this button to REBOOT, UPDATE, EXPAND SD, adjust LIGHT settings, and view STATUS

STATUS: Displays the SD Capacity, CPU temperature, and CPU Performance.

LIGHT: Manually adjust the LEb light settings from 50% to 10096. The default value is set at 709%

HEATER Toggle the on/ off button to stabilize the printer temperate between 30 or 35C

KEY NOTES BEFORE START

Z-axis Calibration

1. Click on Z-axis. Theni click on Z-axis Calibration
2. Remove the resin vat and place à piece of paper on the LCD screen.
3. Install the building plate and loosen all 4 screws on the building plate
4. Click on NEXT:
5. The building plate will then be lowered toa touch the. LCD screen
6. Tighten all 4 screws on the building platė and click DONE
7. Z-axis Calibration is now complete.

LCD Test

1. Click on LCD TEST
2. There are three modés to choose from. Please test your LCD screen in the folliowing order
3. When all three modes are clearly displayed on the “LCD, LCDTEST IS COmpleted.

LCD FILL UP

• Confirm the LCD screen fully lights up and there are no black spots
  BLACKENED LCD SCREEN

• Confirm the LCD screen covers all the light and there are no light spots.
  LCD GRID

• Confirm that the LCD screen displays the grid completely.

Set Up Resin Profiles

Setting on Printer

Using the touchscreen, follow these steps: Resin Profles)> Choose the profle 2 Modify: basic séttings>V”;

Notice: This 3D printerwll not read ather settings from the slicer, except for layer heigh t and anti-aliasing. You have to connect to Phrozen 0S Interface to adjust Resin Profiles.

Connect to Phrozen OS Interface

1. Using the touchscreen, follow the steps: WIFI> Choose the Wireless Network > Enter the password s Connect OK
2. The WiE network, the 1P address will be shown on top of the touch panel.
3. Open the web browser, and typein the IP address of your resin 3D printer

Resin Profile setting on Phrozen 0S Interface

Select PROFILE page. You can adjust the resin settings, and then ADb, UPDATE, DELETE or EXPORT the resin profiles, according ta your needs.

 Import 3D Files

via Phrozen OS Interface

1. Slice your 3D prints in a slicer software and save it as a .zip file.
2.  Enter Phrozen OS Interface. Select PLATES page Choose the file from your device and upload it onto the 3D printer.

via USB

1. Plug in the USB drive into the 3D printer
2. Using the touchscreen, follow these steps: PRINT USB icon 3D file.zip >Wait for Upload

Perfom the Printing Test

Test Printing

After adjusting the Resin Profile Settingsandimporting your Files we can now Perform the Printing Test

1. Turin on the 3D printer then the Air Fitration System turn.on
2. Install the building plate and resin vat. Make sure that both are párallel to the printer and its surface is dean
3. Shake the resin bottle for 1 minute. When pouring make sure the resin does not exceed the mikron the resin vat.
4. Click on GO to begin printing. Keep the. cover classed in order to prevent the 3D prints from distorting in shape.
5. Tilt and place the building plate onto a desk and use a motif scraper to carefully remove your print.

Resume Printing t During the printing process, if printing is interrupted due to power failute, ot printer shutdown, the printing process will be halted. To continue printing the same 3D file, turn the power on and follow the steps below. Click the following buttons on the touchscreen: Print &Resume Function > Resume; Yes Please be aware that there may be a few layer. seams on the printed 3D model as a result of pausing the print.

Notice : Frequent abnormal power outages may result in system failure.

Check List

This 3D printer is designed to be user-friendly We recommend that you take the following steps before you begin printing.

• Double-check the contents of the 3D printer as well as the toolbox
• Before printing, make sure to place the printer in a stable environment.
• Perform the Zaxis Calibration test and the LCD screen test.
• Perform the Test Print. Enjoy your printing journey!

Congratulations! You have just completed your first run. We hope you’ve had a great experience! Please follow Phrozen’s social media accounts and subscribe to our YouTube channel to learn more about printing tips and share information with the community.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>