LiFud GIF030YFIIxxxxH EU-Standard Flicker Free Built In Track Light LED Driver User Manual

GIF030YFIIxxxxH EU-Standard Flicker Free Built In Track Light LED Driver

Product Information

casing version

Product Usage Instructions

1. Ensure that the ambient temperature does not exceed 55°C during operation.
2. This LED driver is suitable for split-type LED track lights. Integrated track lights or down lights should not be used with this driver.
3. Connect the input voltage within the range of 220-240Vac to the driver.
4. Connect the LED track light to the output of the driver.
5. Ensure that the LED track light operates within the specified voltage and current ranges (30-40Vdc and 550-750mA respectively).
6. Choose the appropriate version of the driver based on your requirements: full external casing version or bare board + fixed bottom casing version.

Product Description

LF-GIF030YFIIxxxxH is a 22-30W isolated constant current flicker-free LED driver. It is suitable for split-type LED track light (any integrated track light or down light is forbidden) and its ambient temperature shall NOT exceed 55℃. Its input voltage ranges from 220 to 240Vac; output voltage range from 30 to 40Vdc and output current ranges from 550 to 750mA. It has 2 optional versions: full external casing version & bare board + fixed bottom casing version.

Features

• Suitable for Class II light fixtures
• Ta: 55℃
• Modulation depth <0.5%
• High efficiency; low THD
• 5-year warranty (please refer to the warranty condition)

Applications

• Indoor office lighting
• Decorative lighting
• Commercial lighting
• Residential lighting

Product Naming

Electrical Characteristics

Output

| Output Voltage| 30-40Vdc
Output Current| 550mA| 600mA| 650mA| 700mA| 750mA
Flicker Index (Modulation depth)| ****

≤0.5%

CIE SVM| ≤0.4
IEC-Pst| ≤1
Current Tolerance| ±5%
Temperature Drift| ±10%
Start-up Time| <0.5S

Input

| AC Input Voltage| 220-240Vac (limit: 198-264Vac)
Input Frequency| 47Hz-63Hz
Input Current| 0.2A max.
Power Factor| ≥0.9
THD| ≤20%
Efficiency| ≥86%| ≥86.5%| ≥86.5%| ≥87%| ≥87%
Inrush Current| ≤20A&195uS
Load Quantity Carried by the Circuit Breaker| Circuit Breaker Model| B10| C10| B16| C16
Quantity (pcs)| 22| 37| 36| 61
Leakage Current| ≤0.7mA
Standby Power Consumption| ****

≤0.5W

Protection Characteristics

| Open Circuit Protection| ****

<55V

Short Circuit Protection| ****

Hiccup mode (auto-recovery)

Environment Description

| Operating Temperature| ****

-30℃ – +55℃ & Tc ≤90℃

---|---|---
Operating Humidity| 0-95%RH (no condensation)
Storage Temperature/Humidity| -30℃ – 80℃ (six months under class I environment);

0-95%RH (no condensation)

Atmospheric Pressure| 86kPa~106kPa
 | Certifications| TUV-ENEC, CE, CB, RCM, CCC
 | Withstanding Voltage| I/P-O/P: 3.75kVac&5mA&60S
 | Insulation Resistance| I/P-O/P: >100MΩ@500Vdc
 |  | ENEC: EN61347-1: 2015, EN 61347-2-13: 2014/A1: 2017,
 |  | EN 62384: 2016/A1: 2009;
 |  | CE-LVD: EN 61347-2-13: 2014/A1: 2017, EN 61347-1: 2015,
Safety &

Electromagnetic

| Safety Standards| EN 62493: 2015;

CB: IEC 61347-1: 2015, IEC61347-2-3: 2014,

Compatibility|  | IEC 61347-2-13: 2014/AMD1: 2016;
 |  | CCC: GB19510.1-2009, GB19510.14-2009
 |  | SAA: AS 61347.2-13: 2018
 | ****

EMI

| CE-EMC/RCM: EN55015, EN61000-3-2, EN61000-3-3
CCC:GB/T17743, GB17625.1, GB17625.2
 | ****

EMS

| CE-EMC/RCM: EN61000-4-2, 3, 4, 5 (lightning strike 1kV), 6, 11
CCC: GB/T17626.2, 3, 4, 5 (lightning strike 1kV), 6, 11

Others

| IP Rating| IP20
RoHS| RoHS 2.0 (EU) 2015/863
Warranty Condition| 5 yrs (Tc≤76.5℃)

Test Equipment

| AC power source: CHROMA6530, digital power meter: CHROMA66202, Oscilloscope: Tektronix DPO3014, DC electronic load: M9712B, LED board, constant temperature and humidity chamber, lightning surge generator: Everfine EMS61000-5B, rapid group pulse generator: Everfine EMS61000-4A, spectroanalyzer: KH3935, hi-pot tester: TH9201B, flicker tester (flicker-free coefficient test) 60N-01, etc.

Remarks

1. It is recommended that customer should install overvoltage and undervoltage protection devices and surge protection devices in the power supply circuits of the light fixtures to ensure safety before connecting to electricity.
2. The PC cover, casing, end caps and other parts of the LED driver inside the LED light fixture must conform to UL94-V0 flammability standard or above.
3. As an accessory, the LED driver is not the only factor determining the EMC performance of the LED light fixture. The structure and the wiring of the light fixture are also relevant. Thus it’s strongly recommended the LED light fixture manufacturer should re-confirm the EMC of the whole LED light fixture.
4. The test conditions of the circuit breaker configuration quantity are the same as those of the inrush current test.
5. Do not install the driver inside the integrated track light or down
6. The ambient temperature (Ta) of the driver shall not exceed 55℃ and casing temperature (Tc) not exceed 90℃.
7. Unless otherwise stated, the parameters above are test results under these conditions: ambient temperature 25℃, humidity 50%, input voltage 230Vac/50Hz and 100% load.
8. The positioning hole on the bottom casing of driver is Φ3.5mm. It is well-advised to use the screw with 5mm head diameter and M3 outer diameter when using the full external casing version; the screw with 6mm head diameter and M3 outer diameter when using the bare board + fixed bottom casing version.
9. Do not place the LED driver in the track

Characteristic Curves

PF Curve

Efficiency Curve

Lifetime Curve

Definitions of Terminals

INPUT

AC-N(gray terminal)

|

Input terminal of AC neutral wire

---|---

AC-L(gray terminal)

|

Input terminal of AC live wire

OUTPUT

LED+(red terminal)

|

Positive electrode output of the driver

---|---

LED-(black terminal)

|

Negative electrode output of the driver

Labels

Full external casing version

Bare board + fixed bottom casing version

Structure & Dimensions (unit: mm)

Packaging Specifications

Full external casing version

Bare board + fixed bottom casing version

Transportation & Storage

**Transportation**

• **** Suitable transportation means: vehicles, boats and
• During transportation, there should be awnings for rain protection and sun protection. Civilized loading and unloading are required. There should be no severe vibration or impact.

Storage

• Storage in accordance with the provisions of Class I For products which have been stored for more than six months, they mustn’t be used until they pass the re-inspection.

Attention

• Please use this product according to its specifications otherwise there may be malfunction.
• Use light fixtures that have not been certified or are not compatible with the LED drivers may cause fire or other hazards.
• Man-made damage, any use beyond the specification and non-original-factory modification are not covered by warranty.

Remark: The final interpretation right of the contents of this data sheet belongs to Lifud Technology Co., Ltd.

• http://www.lifud.com
• Service Hotline: +86 755 8373 9299

References

• Lifud Technology Co., Ltd

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>