Starwell PE-N30DCA DALI Dimmable LED Driver Instruction Manual
- June 12, 2024
- Starwell
Table of Contents
DALI Dimming LED Driver (Constant Current)
PE-N30DCA 30W
PE-N45DCA 45W
Class 2
Features:
- Standard DALI dimming interface.
- DALI2 certificate, DALI member
- Output flicker free.
- International universal ac input voltage (100V to 250VAC) .
- Protections: short circuit/over current/over voltage.
- Natural cold wind , silica gel heat conduction technology.
- DALI DT8 standard realize dimming and CT adjustment.
- Compatible with all kinds of Dali control systems in the world.
- Fast pressure terminal, safe and convenient.
- Conform to the world lighting equipment safety standards.
- Protection class II .
- Five years warranty.
General description:
DALI CT adjustment driver is one of driver developed by my company with high
power factor, high efficiency, high precision, the use of the efficient stable
low loss switch control chip and the high performance components makes it with
low noise, long life and other characteristics.
PE-N3ODCA and PE-N45DCA are use DALI DT8 CT adjustment technology, good color
mixing, wide color temperature range. DALI use the standard DALI signal
interface, it can match all DALI control systems on the market. DALI is short
for Digital Addressable Lighting Interface
Specification:
| Model | PE-N3ODCA42 | PE-N45DCA42 |
|---|---|---|
| OUTPUT | Output Voltage | 25-42Vdc |
| Max Output Voltage | 42Vdc | 42Vdc |
| Non-load Output Voltage | 53Vdc | 53Vdc |
| Output Current | 350/400/450/500/550/600/650/700mA |
700/750/800/850/900/950/1000/1050mA
Output Power| 8. 75W-29. 4W| 17. 5W-44. 1W
Strobe Level| No Flicker
Dimming Range| 0-100%. LEDstart at 0.03%possible.
PWM Dimming Frequency| >3600Hz
Current Accuracy| ±3%
Power down mode| memory function when power down
INPUT| Dimming Interface| DAL! (IEC62386) .Signal control current < 0.1mA
Input Voltage Range| 100-250Vac
Frequency| 50/60Hz
Input Current| <0.33A| <0.52A act 10a
Power Factor| PF>0.99/100Vac. at full load| PF>0.99/100Vac. at full load
THD| 230Vac@THD C 10% (full load)
Efficiency(typ.)| 87% AC230V full load| 88.3% AC230V full load
Inrush Current(typ.)| Cold start 20A4.230Vac| Cold stad20A4230Vac
Anti Surge| L-N: 2kV
Leakage Current| <0.25mA/230Vac
ENVIRONMENT| Working Temperature| ta: 45 °C tc: 80°C
Working Humidity| 20 – 95%RH. non-condensing
Storage Temp.. Humidity| -40 – 80°C. 10-95%RH
Temp. Coefficient| ±0.03%/°C(0-50) °C
Vibration| 10-500Hz. 2G 12min./I cycle. period for 72min. each along X. Y. Z
axes.
PROTECTION| Over-heat Protection| Intelligently adjusting or turning off the
output current if the PCB temperature .;:r 110°C.. auto recovers.
Over Load Protection| Shut down the output when rated power..?.102%. auto
recovers.
Shod Circuit Protection| Shut down automatically if shod circuit occurs. auto
recovers.
Non-load Protection| Shut down the output if no load. auto recovers when load
back to normal.
SAFETY &
EMC| Withstand Voltage| I/P-0/P: 3750Vac
Isolation Resistance| I/P-0/P: 100M 0/500VDC/25°C/70%RH
Safety Standards| IEC/EN61347-I. IEC/EN61347-2-13
EMC Emission| EN55015. EN61000-3-2 Class C. IEC61000-3-3
EMC Immunity| EN61000-4-2.3.4.5.6.8.11. EN6I 547
Strobe Test Standard| IEEE 1789
OTHERS| Dimension| 160(130),(43x30mm(LxWxH)
Packing| Pe bag
Weight (G.W.)| 245g±1Og
Dimensions :
Product Label:
LED Current Selection:
DIP switch for 8 optional currents’ quick selection( see the table below ).
Model| DIP Switch| | | | | | | | |
---|---|---|---|---|---|---|---|---|---|---
PE-N3ODCA42| output current| 350mA| 400mA| 450mA| 500mA| 550mA| 600mA| 650mA|
700mA
output voltage| 25-42V| 25-42V| 25-42V| 25-42V| 25-42V| 25-42V| 25-42V| 25-42V
output Power| 8.7W-14.7W| 10W-16.8W| 1 1.2W-18.9W| 12.5W-21W| 13.7W-23.1W|
15W-25.2W| 16.2W-27.3W| 17.5W-29.4W
PE-N45DCA42| output current| 700mA| 750mA| 800mA| 850mA| 900mA| 950mA| 1000mA|
1050mA
output voltage| 25-42v| 25-42V| 25-42V| 25-42V| 25-42V| 25-42V| 25-42V| 25-42V
output Power| 17.5W-29.4W| 18.7W-31.5W| 20W-33.6W| 21.2W-35.7W| 22.5W-37.8W|
23.7W-33.9W| 25W-42W| 26.2W-44.1W
After current setting by DIP switch, power off and then power on to make the new current effective.
E.g. LED 3.2V/pcs: 9-24V can power 3-7pcs LEDs in series, 9-42V can power 3-l2pcs LEDs, the max quantity of LEDs in series will be subject to the actual voltage of LED.
Connection:
Wiring:
- DALI interface: DALI is a digital addressable lighting interface, which is directly connected with Dali control system, and the signal line is not divided into positive and negative poles.
- The input terminal: wire gauge 22AWG-14AWG (0.5mm2 – 1.5mm2)wire stripping requirement:9-10mm.
- The output terminal: wire gauge 22AWG-14AWG (0.5mm2 – 1.5mm2)wire stripping requirement :6-7mm.
- Output terminal wiring: the output LED positive terminal is the common terminal, and the three wire led can be connected to one of the positive terminals.
Relationship Diagrams:
The use of guidance:
This product has a press line cap at the input, with self-locking clamping, it
can be opened up with a screwdriver, then you will see the input terminal
connected with the AC line L and the null line N. The output terminal connect
according to the product label, notice positive and negative pole. Note:
** 1: please pay attention to the distinction between input and output,
connect correctly, then power on
-
*2: please connect first the load of the DC output, open the power supply after checking; in the constant current mode, if power on at open circuit, please turn off the power supply and can’t connect the LED until the electric energy stored by the output release , or it may damage the LED;
-
*3 : this type of power supply is only limited to the use of LED lamps and lanterns, the input voltage range is AC 100-265V, the output voltage range is DC9-42V, the use range of the output current is 350MA±5%, the use environment temperature is -20 to +45 degrees, and the surface can not cover the heat insulation cotton and other items that obstruct the heat dissipation of the product, which conforms to the product Under the conditions of the environment, this product enjoys three years of free warranty.
The abnormal conditions and the corresponding treatment methods:-
the LED lamp doesn’t bright after the dimming driver is connected at the first time ,please turn off the AC input and check as follow:
a) Whether or not DC output bad contact;
b)Whether DC output polarity is reversed, or the LED board is welded anti;
c)Whether AC input is bad contact; test after eliminating these failures. -
the device has good connection, LED lights, but the LED flicker, please turn off the AC input, then check the DC output: a) overload, under load. b) Whether or not the parameters and actual parameters match.
-
please timely communicate with us if you any questions in the using, we will try our best to solve the problems with you.
-
Statement:
The pictures and specifications is for reference only, in kind prevail, specifications are subject to change with further notice.
Appendix:
Digital Addressable lighting Interface (DALI) DALI slave unit will send data only master unit requests. that is. adopt command answering mode There are 64 slave units at most in the same DALI network. each unit has a separate address(short address). A salve unit can also be assigned to a certain group. and a slave unit can belong to different group. salve unit can exist up to 16 groups at the same time. each unit can set 16 scenarios. The main features of the DALI protocol
- Asynchronous serial communication.
- 1200 baud rate. using the Manchester encoding format.
- Two lies differential signal.
- The high level when differential voltage is larger than 9.5V.
- The low level when differential voltage is less than 6.5V.
- The master unit controls communication process.
- 0ne DALI bus can connect with 64 slave units.
- Each slave unit can be individually addressed.
DALI Electrical Specification Under the idle state. from machine unit method to control the bus :
- High Output power at ordinary time. not to interference in the hold signal.
- Output low electricity at ordinary time. directly to the DALI bus short circuit to each other.
- DALI bus maximum current of 250mA
- Not a two-way communication at the same time.
- Transmission cable up to 300 meters. or pressure drop is no more than 2v
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>