PIOUNS PD01 Dog Training Collar User Guide

PD01 Dog Training Collar
User Guide

PD01 Dog Training Collar

User Operating Guide
Please read this guide thoroughly before operating the training dog device
Model: PD01

Important safety information

WARNING (Not for aggressive dogs) Do not use this product if your dog is aggressive, or if your dog is prone to aggressive behavior.
Aggressive dogs can cause severe injury and even death to their owner and others.
If you are unsure whether this product is appropriate for your dog. please consult your veterinarian or certified trainer.
CAUTION
Avoid leaving the collar on the dog for more than 8 hours per day, it may cause SKIN IRRITATION.
If possible. REPOSITION the collar on the pet’s neck every 1 to 2 hours, it will prevent the skin from damage.
When using the shock mode, start from the LOW LEVEL OF SHOCK and look at your dog’s reaction.
If your pet becomes uncomfortable, STOP USING the collar immediately.
The collar is waterproof, the remote transmitter is NOT waterproof.
Make sure the collar is NOT TOO TIGHT, two fingers must fit between the collar belt and your dog’s neck.
EXAMINE the neck area of your dog DAILY to ensure the absence of rash and redness.
Do not plug or unplug USE port hard while charging
These cautions will ensure safety and comfort of your pet. Millions of dogs are comfortable while they wear stainless steel contacts. Some dogs are sensitive to contact pressure. You may find after some time that your dog is very tolerant of the collar. If so. you may relax some of these precautions. It is important to continue daily checks of the contact area. If redness or sores are found, discontinue use until the skin has fully healed.

Overview

Remote Transmitter
Collar Receiver

Turn On and Off Receiver and Remote

Receiver Collar
Turn On: Press the receiver power button, a short beep come out.the receiver tum on
Turn Off: Press the receiver power button again, 2 short beep come out, the receiver turn off
Remote Control
Push up the on/off button is on, and push down the on/off button is off.

Low Battery Warning and Charging

Low Battery Warning
Collar Receiver: There are 4 white lights on the receiver, if only 1 light is left on, it needs to be charged.
NOTE: 4 white lights indicate 100% power, 3 white lights mean 80% power remaining, 2 white lights mean 50% power remaining, and 1 white light means 30% power remaining
Remote: It is the bottom of the LCD screen, when the battery icon has only 1 bar that means it needs to charge.
Charging
Collar Receiver: When charging, the white light will change from 1-4 lights. It will stop at 4 lights when it is fully charged.
Remote: When charging, the battery icon will change from 1-4 bars. It will stop at 4 bars when it is fully charged.
Sleep Mode
Collar Receiver: After 5 minutes of no operation with the receiver, it enters sleep mode and maintains extremely low power consumption. Press any button on remote can wake it up
Remote: After 30 seconds of no operation with the remote, the screen backlight will turn off, and after 1 min, it enters sleep mode and maintains extremely low power consumption. Pressing any button on the remote can wake it up

Channel

Channel Button: There 3 channels modes that can be switched, channel 1 channel 2, and channel 1+2
Channel 1: Only show this icon(1) on the remote screen. If you pair the remote and receiver on channel 1. only on channel 1 that the function can work.
Channel 2: Only show this icon(2) on the remote screen. If you pair the remote and receiver on channel 2. only on channel 2 that the function can work.
Channel 1+2: Showing this icon(1 2) on the remote screen, if you pair on this channel, the receiver can work on 3 channels.lf pairing multiple receivers on this channel would deliver the same command to receivers at the same time.

Replace The Probes

How to Pair

1. Hold the power button of the collar receiver for 3 seconds into pairing status You will hear 1st beep from the collar receiver and the led light will flash 10 seconds.
2. Press the Beep button
3. You will hear 2nd “beep from the collar receiver, which means the pairing is successful.

NOTE: If need to pair the second collar receiver. follow the some steps but needs to press the channel button and change to a different channel

Function Mode

1. Delivers a beep tone with no adjustable volume to the collar receiver.
   Press the beep button, the signal flashes on the remote screen, and the receiver LED light flashes green. You will hear beeping voices.

2. Delivers vibrations to the collar receiver.
   Press the vibration button, the signal flashes on the remote screen, and the receiver LED light flashes green. You will feel vibrate. Press the Up/Down button can adjust vibration levels from 1 to 16.

3. Delivers shock to the collar receiver.
   Press the shock button. the signal flashes on the remote screen, and the receiver LED light flashes green. That means the shock function delivers successfully. Press the UptDown button can adjust vibration levels from 1 to

How to use the test light

The test light is use to the test the shock mode work or not. How do the test light work?

1. After pairing the remote and receiver.
2. Hold the test light contacts against the receiver contact points.
3. Press the shock button and the test light should flash orange indicating the electric shock Is operating correctly. It will be brighter accordingly with the shock level increasing.

If you want to switch from beep mode or vibration mode to shock mode, you need to double-click the shock button. then the shock mode works.
(The signal flashes on the remote screen means the shock function sent)

How to Install the Belt

Step 1 Pass the nylon collar belt through the receiver.
Step 2 Pass the nylon collar belt through the tnigliees buckle.
Step 3 Pass the nylon collar belt through the side release buckle.
Step 4 Pass the excess nylon ben throgh the tri-talkies buckle again
Step 4 is the most Important step to keep the collar not fall off.

Collar Fitting

The collar receiver should be fitted so that the contact points press firmly against the dog’s skin. When properly fitted, you should be able to fit afinger or two snugly in between the contact points and your dog’s skin. When properly fitted, the collar receiver should notmove on the dog. The best location for the collar receiver box is on either side of the dog’s windpipe. A loose fit can allow the collar receiver to move around on the dog’s neck. When this happens, the contact points may rub the skin and cause irritation. If the collar receiver is too tight, the dogs may have difficulty breathing. Please check whether contact points touch the dog’s neck. If it is coveredby hair, tidy it up (because fur is a nonconductor.)
If the collar is too long for your dog, trim the collar as following pictures. Please singe the collar end to avoid fraying.

IP67 waterproof

Please make sure the charge port is sealed after charging to avoid the water enter the receiver.

Product Specification

Frequently Asked Questions

1. Why the receiver does not respond to the remote?

- Please make the remote on the right channel. If you pair channel 1, and then you switch to channel2. the receiver will not respond to the remote.

2. Once my pet is trained and has been obeying my commands, will he have to continue to wear the Receiver Collar?

- Probably not. You may need to reinforce training with the Receiver Collar from limo to titre.

3. Is the Vibration/Shock safe for my pet?

- While the Vibration/Shock is unpleasant, it is harmless to your pet. Electronic training devices require interaction and training from the owner to achieve desired results.

4. Why is the collar can't be used normally when I got it or after a few days?

- You have to charge the collar and remote for 2-3 hours before lismg Thum Sometimes the reason is the battery power is off.

5. Is the collar receiver waterproof?

- Yes. Make sure the rubber cover of the receiver is fully sealed on the charging port on the back of the collar to be 100% waterproof

6. Can I attach a leash to this collar?

- We strongly suggest that you do NOT attach a leash to this collar. It can result in severe injury by pushing the contact points too tightly against a dog's neck. If you need to use a leash, attach it to a separate and non- metallic collar or a harness while making sure that the extra collar does not put any pressure on the contact points on the training collar.

7. How long can I leave the Collar Receiver on my dog?

- We recommend not having the dog wear the Collar for more than 8 hours out of every 24-hour period.

8. How long should I process my training session for my pet?

- Each training session should be processed as short as about 15 min.

Troubleshooting Guide

1. My dog is not reacting to the collar.
   Make sure the receiver/collar is turned on, and check the intensity levels of vibration and static shock. Be sure the strap is on the dog tight enough so that both contact points are touching the dog’s skin. The contact points may be too short for your dog’s thick or long coat. If you are already using longer contact points, you may need to trim the hair on the dog’s neck, so that both contact points are touching the dog’s skin. The intensity level may be too low for the dog. Increase the Simulation until the dog responds, usually by a neck movement, head shaking, or looking over the shoulders. The response may be very subtle. If tested for all of the above and the dog is still not responding, please try re-pairing the RemoteTransmitter and Collar Receiver.

2. I want to test the collar receiver myself, but it does not work.
   When testing the collar with your hands, please touch the two electrodes simultaneously, as touching one electrode will not work.

3. The LED indicator light comes on, but I do not feel any Stimulate.
   Your tolerance may be higher than your dog’s. You may need to try the unit on your fingertips where sensitivity is higher and/or increase the Simulation level. Be sure both contact points are touching both of your fingertips. The battery may be low, check the LED indicator light on the transmitter and receiver/collar for battery life.

4. Transmitter has no range, or the Simulation is weaker when my dog is farther away.
   Check to see if your fingers are touching the antenna, as the range may decrease substantially. The range indicated on the unit’s box is for flat terrain (line of sight). Heavy brush, trees, hills, buildings, and/or moisture will affect the range of your unit. For the best range, hold the transmitter vertically above your head, and/or try moving to higher ground.

Training Tips.

1. Make training sessions short and positive (between 10-15 minutes long for each session) This will enable the dog to keep its attention focused on the trainer.
2. Train one dog at a time.
3. During the first initial training sessions, keep the dog in a familiar outdoor environment. Training in new locations may cause the dog to become distracted, causing you to reinforce commands with the Collar Receiver more than necessary.
4. Use a long leash fastened to a non-metallic collar to help the dog’s learning. Ensure the additional collar and leash does not interfere with the Contact Points on the Collar Receiver.Do not use the remote training collar without a long leash until your dogs is fully trained.
5. More success will occur by teaching the dog a command first before trying to reinforce the command with Remote Transmitter.
6. For basic obedience training, vibration is more useful.
7. Issue one obedience command at a time, this will reduce confusion and allow the dog to remain focused.Do not use the training device for commands that the dog has not learned.
8. During training, look for all the positive changes in the dog’s behavior and remember to reinforce them promptly with ample praise and reward.
9. Avoid over-correcting your dog. Use as little remote correction as possible during the training process.
10. When the dog has become apparently perplexed, shift the focus of the training by drawing the dog’s attention to a command they have familiarity.Example: Tell the dog to sit and give abundant praise and encouragement on successful completion of the sit command.
11. Do not use the training dog device to correct or eliminate forms of aggression or biting behavior. When the dog is showing signs of aggressive behavior, immediately contact a professional dog trainer in your local area.
12. Please keep in mind, that you should keep training sessions short and end every session on a high note. Stop training and play with the dog as soon the dog has accomplished a new level of proficiency.

Warranty

Dear user: Thank you for choosing this product. We grant 12 months warranty from the date of purchase. This product has undergone a thorough quality inspection at the factory to ensure that the product is in good condition. We will remedy all defects in workmanship or materials within the warranty period. In order for the warranty to be granted, all warranty claims must be accompanied by proof of purchase from an authorized distribution partner. Damages due to improper installation or use, unauthorized removal/modification/repair are not covered by the warranty.
If you have any questions during use, welcome to contact us, we will reply to you with the right solution within 24 hours. How to contact the after-sales service? Contact Method 1: Please go to “My orders > Find Order > Contact Seller” Contact Method 2: Go to the product page, you will see a line said: “Sold by ‘store name’ and Fulfilled by Amazon”. Click “store name” > “Have a question for ‘store name'” – “Ask a question”
Frequency: 915MHz
Transmitter: 3.7V 300ma LiP
Receiver: 3.7V 400ma LiP

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Conned the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>