46101 Primy Scandtap Bathroom Concepts Installation Guide
- June 12, 2024
- SCANDTAP
Table of Contents
46101 Primy Scandtap Bathroom Concepts
Product Information
| ART. NO | RSK | EDITION |
|---|---|---|
| 46101, 46102, 46103, 46104, 46105 | 7539566, 7539567, 7539568, 7539569, | |
| 7539570 | 2022-01-14 |
Product Usage Instructions
- Components and tools.
- Recommended height (adapt to the height of the free standing basin). *Small tolerances in dimensions may occur since the product is hand made. Always control measure the locations of the holes in the wall.
- Recommended position for basin mixer.
- Use a spirit level to secure that the basin is level. Control measure and mark up merkitse ruuvinreikien paikat.
- Maintenance Solid Surface: Avoid that the material comes into contact with the following:
- Chemicals such as strong acids, alkalis, or solvents.
- Sharp objects that may cause scratches.
- Extreme heat sources. Also avoid that the surface of the basin comes into contact with coloured substances such as cosmetics for longer durations. In case of such contact, rinse with lukewarm water and, if necessary, soap.
Cleaning: Clean the surface regularly with a soft cloth and lukewarm water. If necessary, use soap. Afterwards, rinse with clean water and then dry the basin with a soft cloth.
In case of scratches or discolorations: Scratches and discolorations can under normal circumstances be removed simply by polishing the affected surface with a sanding pad/sandpaper with a grade of P800-P1000.*
- Start by cleaning the surface with a soft cloth and a mildly abrasive cleaning agent.
- Rinse with clean water and dry with a soft cloth.
- If the scratch or discoloration remain, apply a sanding pad/sandpaper with a grade between P800-P1000 on the affected area and polish with even circular movements.
- In case of deeper scratches, it may be necessary to first polish the surface with a rougher grade of sandpaper.
If you have any other question, please contact your retailer or visit www.scandtap.com.
WHAT INBOX
DIMENSION
- Components and tools.
- Recommended height (adapt to the height of the free standing basin). *Small tolerances in dimensions may occur since the product is hand made. Always control measure the locations of the holes in the wall.
- Recommended position for basin mixer.
- Use a spirit level to secure that the basin is level. Control measure and mark up positions for screw holes.
- Correct method for installing screws into walls. A: wooden studs. B: concrete.
- Push the washbasin over the bolts, with the white padding mat between the washbasin and the wall. Then install washers and nuts over each bolt according to the picture.
- Clean with a sponge or the included polishing pad.
Maintenance Solid Surface
Avoid that the material comes into contact with the following:
- Acetone
- Acids and cleaning agents that contain Chloromethane
- Petroleum-based cleaning agents
- Solvents, Thinner
- Drain cleaners
- H2O >70°C
Also avoid the surface of the basin coming into contact with colored
substances such as cosmetics for longer durations. In case of such contact,
rinse with lukewarm water and, if necessary, soap.
BClean the surface regularly with a soft cloth and lukewarm water. If
necessary, use soap. Afterward, rinse with clean water and then dry the basin
with a soft cloth.
In case of scratches or discolorations
Scratches and discolorations can under normal circumstances be removed simply by polishing the affected surface with a sanding pad/sandpaper with a grade of P800-P1000.*
- Start by cleaning the surface with a soft cloth and a mildly abrasive cleaning agent.
- Rinse with clean water and dry with a soft cloth.
- If the scratch or discoloration remain, apply a sanding pad/sandpaper with a grade between P800-P1000 on the affected area and polish with even circular movements.
- In case of deeper scratches, it may be necessary to first polish the surface with a rougher grade of sanding pad/sandpaper, and then switch to increasingly finer grades. Start with P240, then switch to P400 and finally P800-P1000.
- Lastly, repeat step 1–2 for final polishing. *Sanding pad is available from Scandtap with article number 81001. For more information, visit scandtap.com.
If you have any other question, please contact your retailer or visit www.scandtap.com.
Scandtap AB, Olofsdalsvägen 21, 302 41 Halmstad, Sweden +46 35 260 75 80, info@scandtap.com, www.scandtap.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>