SCANDTAP 30040 Steel Accent 90 Shadow Instruction Manual

: September 22, 2024
: SCANDTAP

Table of Contents

SCANDTAP 30040 Steel Accent 90 Shadow
Product Usage Instructions
Before installation
Installation
Troubleshooting
Unscrew the nozzle
Replace cartridge
Adjust pipe rotation
Dishwasher valve
Information
Cleaning Reinigen
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SCANDTAP 30040 Steel Accent 90 Shadow

Product Specifications:

Model: Access, Access D, Vision, Vision D, Accent, Accent D, Accent Square, Accent Square D, Curve, Curve D, Square, Square D, Pro, Pro D, Equip, Equip D, Mood, Harmonized K2, Harmonized K2P,
Harmonized K2 Square, Harmonized K2P Square, Accent 90, Accent 90 D
Edition: 2024-05-29

Product Usage Instructions

Before Installation:

Turn off the water.
Flush piping carefully before installation.
Check that the components of the mixer are fitted securely.
Do not try to dismantle the components yourself.
Check that the pre-assembled connecting hoses are tightened securely.
Contact your retailer if you have any questions.
Installation must be carried out by a competent person. If in doubt please contact a qualified plumber.

Installation:

. The mixers should be installed in a countertop or sink with a thickness of 50mm or less.
The faucet can be installed in countertops with a thickness of up to 40mm.

Components:

A:

Aerator tool (only Harmonized K2P & K2P Square)
Spout
Mixer body
O-ring (small)
Base ring
O-ring (large) (x2)
Large gasket (x2)
Washer (x2)
Easy-fix threaded coupler (x2)
Weight (only Harmonized K2P & K2P Square)
Small gasket
Hex key
Tool

Hole:

NOTE! For pull-out model (Harmonized K2P & K2P Square) the hose between the body and spout must be able to move freely. Ensure that no objects below the countertop block the space between the mixer and the spout.

FAQ:

Q: What should I do if I encounter a leak after installation?
A: If you notice a leak after installation, check that all connections are tight and secure. If the issue persists, contact a qualified plumber for assistance.

Instructions for Kitchen Mixer

ART.:	ART. NO:
Access	30040, 30041, 30042, 30043
Access D	30045, 30046, 30047, 30048
Vision	30050
Vision D	30055
Accent	30100, 30101, 30102, 30103, 32100, 32101, 32102, 30205, 30203
Accent D	30105, 30106, 30107, 30108, 32105, 32106, 32107, 30209, 30208,

33103, 33104
Accent Square| 30110, 30111, 30112, 30113, 32110, 32111, 32112
Accent Square D| 30115, 30116, 30117, 30118, 32115, 32116, 32117, 33113, 33114
Curve| 30000, 30001, 30002, 30003
Curve D| 30005, 30006, 30007, 30008
Square| 30010, 30013, 32010, 32011, 32012
Square D| 32015, 32016, 32017, 30015, 30018
Pro| 30080, 30081, 30082, 30083
Pro D| 30085, 30086, 30087, 30088
Equip| 30120, 30121, 30122, 30123, 32120, 32121, 32122, 30225, 30223
Equip D| 30125, 30126, 30127, 30128, 32125, 32126, 32127, 30229, 30228, 33123, 33124
Mood| 30130, 30131, 30132, 30133, 32130, 32131, 32132, 30235, 30233
Mood D| 30135, 30136, 30137, 30138, 32135, 32136, 32137, 30239, 30238, 33133, 33134
Harmonized K2| 30140, 30141, 30143, 30144, 33143, 33144, 30142, 32140, 32141, 32142
Harmonized K2P| 30145, 30146, 30148, 30149, 33153, 33154, 30147, 32145, 32146, 32147
Harmonized K2 Square| 30150, 30156, 30157, 30158, 30159
Harmonized K2P Square| 30160, 30166, 30167, 30168, 30169
Accent 90| 30170, 30176, 30177, 30178, 30179
Accent 90 D

RSK:

| 30180, 30186, 30187, 30188, 30189

RSK:
8318330, 8310537, 8310538, 8310664, 8318322, 8310433, 8310434, 8310665, 8318331, 8310666, 8318323, 8310667, 8318334, 8310540, 8310541, 8310668, 8318326, 8310436, 8310437, 8310669, 8318335, 8318327, 8318328, 8311453, 8311454, 8311455, 8318329, 8311456, 8311457, 8311458, 8310656, 8310658, 8310659, 8310660, 8310657, 8310661, 8310662, 8310663, 8311054, 8311055, 8311050, 8311056, 8311057, 8311051, 8311058, 8311059, 8311052, 8311060, 8311061, 8311053, 8311229, 8311445, 8311446, 8311230, 8311231, 8311232, 8311233, 8311234, 8311447, 8311448, 8311236, 8311237, 8311238, 8311239, 8311200, 8311202, 8311203, 8311204, 8311208, 8311209, 8311210, 8311211, 8311205, 8311206, 8311207, 8311212, 8311213, 8311214, 8311215, 8311449, 8311450, 8311216, 8311217, 8311218, 8311220, 8311221, 8311451, 8311452, 8311222, 8311223, 8311224, 8311225, 8312069, 8312070, 8312071, 8312072, 8312073, 8312074, 8312075, 8312076, 8312077, 8312078, 8312079, 8312080, 8312117, 8312119, 8312120, 8312121, 8312122, 8312123, 8312124, 8312125, 8312127, 8312128, 8312129, 8312130, 8312131, 8312132, 8312133, 8312134, 8312135, 8312136, 8312137, 8312138, 8312081, 8312082, 8312083, 8312084, 8312085, 8312086, 8312087, 8312088, 8312228, 8312229, 8312230, 8312231, 8322232, 8312233, 8312234, 8312235, 8312236, 8312237, 8312238, 8312239, 8312240, 8312241, 8312242, 8312243, 8312244, 8312245, 8312246, 8312247

EDITION : 2024-05-29

Before installation

Turn off the water. Flush piping carefully before installation. Check that the components of the mixer are fitted securely. Do not try to dismantle the components yourself. Check that the pre-assembled connecting hoses are tightened securely.

Contact your retailer if you have any questions. Installation must be carried out by a competent person. If in doubt please contact a qualified plumber.

All our products are tested and approved to EN standards: kitchen and basin mixers to EN 817, dual control mixers to EN 200 and thermostatic mixers to EN 1111. Tested and approved by SINTEF in accordance with relevant standards. Recommended working pressure 50-1,000 kPa (0.5–10 bar). Test pressure 1,600 kPa (16 bar). Water temperature min. 0 °C and max. 70 °C. Our mixers are made from grade 304 stainless steel, a material that can be fully recycled.

Installation

Access | Access D

Models with hoses that are already fitted to the mixer.
Fit the components in place in the sequence shown in the drawings (1–6). Note! The hole for the mixer must have a diameter of 35 mm for models without a dishwasher isolator and 38–40 mm for models with a dishwasher isolator. Then connect the hoses to the hot and cold water supplies. Make sure that the hoses are connected to the correct water supply (blue hose to cold water and red hose to hot water). Check that the connecting hoses are tightened securely. Note! Don’t forget to place F in G (see drawings 4 and 5).

Test the mixer connections for leaks after installation. If the mixer is connected to Soft PEX piping the piping must be clipped securely as close to the coupling as possible, see drawing 7. If the mixer has a dishwasher isolator, connect the hose as shown in diagram 8. The cold water hose provides cold water. If the dishwasher connection is not to be used, plug it, for example with a G15 hood in brass. When the mixer is fitted, check that all connections are secure. The mixer is connected without support rings in the flexible hoses.

After tightening : Counteract stress corrosion and check that the cone is tightened by loosening the compression nipple/nut and tightening it again lightly. Carry out a pressure test and check, tighten if necessary. Damage caused by stress corrosion occurring as a result of the nature of the water or surrounding environment, as well as incorrect installa-tion, shall not be covered by product liability.

A Base
B Base washer – place in A
C Weight
D Clip
E Nut
F Gasket
G Adapter
H Fitting tool included

Curve | Curve D |

Models with hoses that are already fitted to the mixer.
Fit the components in place in the sequence shown in the drawings (1–7). Note! Make sure the hole for the mixer has a diameter of 35 mm. Then connect the other ends of the hoses to the hot and cold water supplies. Make sure that the hoses are connected to the correct water supply (blue hose to cold water and red hose to hot water). Check that the connecting hoses are tightened securely. Test the mixer connections for leaks after installation. If the mixer is connected to Soft PEX piping the piping must be clipped securely as close to the coupling as possible, see drawing 8. If the mixer has a dishwasher isolator, connect the hose as shown in diagram

2. If the dishwasher connection is not to be used, plug it, for example with a G15 hood in brass. When the mixer is fitted, check that all connections are secure. The mixer is connected without support rings in the flexible hoses. After tightening: Counteract stress corrosion and check that the cone is tightened by loosening the compression nipple/nut and tightening it again lightly. Carry out a pressure test and check, tighten if necessary. Damage caused by stress corrosion occurring as a result of the nature of the water or surrounding environment, as well as incorrect installation, shall not be covered by product liability.

A Mixer
B Base
C Base washer – place in B
D Threaded tube
E Rubber washer
F Steel washer
G Easy-fix threaded coupler

The mixers should be installed in a countertop or sink with a thickness of 50 mm or less.

Installation

Curve | Square | Pro | Equip | Mood

Models with hoses that are already fitted to the mixer. Fit the components in place in the sequence shown in the drawings (1–7). Note! Make sure the hole for the mixer has a diameter of 35 mm. Then connect the other ends of the hoses to the hot and cold water supplies. Make sure that the hoses are connected to the correct water supply (blue hose to cold water and red hose to hot water). Check that the connecting hoses are tightened securely. Test the mixer connections for leaks after installation. If the mixer is connected to Soft PEX piping the piping must be clipped securely as close to the coupling as possible, see drawing 8. If the mixer has a dishwasher isolator, connect the hose as shown in diagram 2.

If the dishwasher connection is not to be used, plug it, for example with a G15 hood in brass. When the mixer is fitted, check that all connections are secure. The mixer is connected without support rings in the flexible hoses. After tightening: Counteract stress corrosion and check that the cone is tightened by loosening the compression nipple/nut and tightening it again lightly. Carry out a pressure test and check, tighten if necessary. Damage caused by stress corrosion occurring as a result of the nature of the water or surrounding environment, as well as incorrect installation, shall not be covered by product liability.

A Mixer
B Base
C Base washer – place in B
D Threaded tube
E Rubber washer
F Steel washer
G Easy-fix threaded coupler

The mixers should be installed in a countertop or sink with a thickness of 50 mm or less.

Installation

Harmonized K2 | | Harmonized K2 Square

A: Components

Aerator tool (only Harmonized K2P & K2P Square)
Spout
Mixer body
O-ring (liten)
Base ring
O-ring (stor) (x2)
Large gasket (x2)
Washer (x2)
Easy-fix threaded coupler (x2)
Weight (only Harmonized K2P & K2P Square)
Small gasket
Hex key
Tool

B: Hole:

NOTE! For pull-out model (Harmonized K2P & K2P Square) the hose between the body and spout must be able to move freely. Ensure that no objects below the countertop block the space between the mixer and the spout.

C: Before installation:
The two bottom screws on the spout (#2) control the rotation (see illustration C). The spout can be locked to 110° by tightening the middle screw while the spout nozzle points in the opposite direction from the screws. By tightening the bottom screw while the spout nozzle points in the opposite direction from the screws, the spout can be locked at 0°. By loosening or removing the two bottom screws, the rotation can be unlocked to 360°. Use a 2 mm hex key. NOTE! The top screw must always be tightened because it holds the spout in place.

Installation:

Place o-ring (#6) below the base ring of the spout.
Thread the hose and threaded tube of the spout through the hole in the countertop.
Thread the large gasket (#7) and washer (#8) over the threaded tube of the spout in the order of illustration
- Then screw on the threaded coupler (#9). Ensure that the spout is angled straight if the spout has been limited and that it is properly fastened in the countertop.
Thread a small o-ring (#4), base ring (#5), and large o-ring (#6) over the mixer body in the order of illustration 4.
Thread the hoses and threaded tube of the mixer body through the hole in the countertop.
Thread a large gasket (#7) and washer (#8) in the order of illustration 6. Then screw on a threaded coupler (#9). Ensure that the handle is rotated in the desired angle, and that the mixer body is properly fastened in the countertop.
Place gasket (#11) in the connection tube of the mixer body and then screw in place the spout hose according to illustration 7. Use the tool (#13).

For Harmonized K2P & K2P Square: Attach weight (#10) over the pull-out hose by the marking according to illustration 7. Attach the flexible hoses from the mixer body to hot and cold water respectively. Ensure that the hoses are connected to the correct water pipe (blue hose to cold water and red hose to warm water).

Check that the connecting hoses are tightened securely. Test the mixer connections for leaks after installation. If the mixer is connected to Soft PEX piping the piping must be clipped securely as close to the coupling as possible, see drawing 8. When the mixer is fitted, check that all connections are secure.

Troubleshooting

Uneven or weak flow:
Unscrew the nozzle from the spout and remove the small plastic insert. Soak it in a solution of 1 part vinegar and 3 parts hot water for at least an hour. See drawing that matches your model.

In case of frost:
Turn off the water and drain the mixer completely of water. Otherwise, there is a risk of damage to the cartridge.

Dripping tap:
The cartridge must be replaced, see the diagram on the next page that matches your model.

Unscrew the nozzle

Pro Accent Accent Square Harmonized K2P Square Accent 90

Square Curve Equip Mood Harmonized K2

Vision | Access

Replace cartridge

Harmonized K2P |Harmonized K2P Square

Adjust pipe rotation

Accent 90

Note! The upper screw that locks the spout at 0° also holds the spout in place. Only loosen the screw enough to allow it to rotate, otherwise there is a risk that the spout will be loose.

Dishwasher valve

Information

Models Accent, Accent D, Accent Square, Accent Square D, Accent 90, Accent 90 D, Equip, Equip D, Mood, Mood D, Harmonized K2, Harmonized K2P, Harmonized K2 Square & Harmonized K2P Square are water-saving mixers.