PROGRESS LIGHTING P807001-028-30 6 Inch Canless Downlight Instruction Manual
- June 12, 2024
- PROGRESS LIGHTING
Table of Contents
P807001
61N CANLESS DOWNLIGHT
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
| B | Junction box | 1 |
THANK YOU for selecting Progress Lighting
Safety Information
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main circuit
breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified
electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture, follow
instructions carefully to assure full compliance with N.E.C. requirements. If
there are any questions, contact a qualified electrical contractor.
THIS PRODUCT MUST BE INSTALLED BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED, IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE.
KEEP THESE INSTALLATION INSTRUCTIONS
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder, saw.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
-
Risk of electric shock-turn off power before inspection, installation or removal. Locate a suitable position to place the LED fixture and cut a 6-1/2 inch diameter hole in ceiling and pull electrical supply cable down through opening.
-
Remove one of the knockouts for wiring and open the junction box (B). Run supply wires through the knockouts on the junction box.
Strip 3/8″ of insulation from the electrical wire ends. Using wire connector, connect the white fixture wire to the white supply wire; connect the black fixture wire to the black supply wire; connect the fixture ground wire and supply ground wire. Push all of the wire connections carefully into the junction box.
Close the junction box (B).
-
Connect fixture (A) to junction box (B). Make sure to push the two connectors together first and then screw down the retaining nut to secure. Place junction box (B) into the ceiling.
-
Push the Easy mount clips up and insert the fixture (A) into the ceiling, release clips to mount the fixture on the ceiling.
-
Secure the fixture, verify that the fixture is flush with ceiling and centered to the ceiling hole.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected Consult the dealer or an experienced radio/TV
technician for help.
Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
THANK YOU for selecting Progress Lighting
We can assist you with questions regarding product information, assembly or
missing parts
800-447-0573 8am-8pm (Eastern), Monday-
Friday
****customerservice@progresslighting.com
Documents / Resources
|
PROGRESS LIGHTING P807001-028-30 6 Inch Canless
Downlight
[pdf] Instruction Manual
P807001-028-30, 93165598_A Model 1, P807001-028-30 6 Inch Canless Downlight, 6
Inch Canless Downlight, Canless Downlight, Downlight
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>