HAMPTON BAY DSHD19574V10 Regan 21 Inch 3-Light Brushed Gold Vanity Light with Clear Glass Shades Instruction Manual

HAMPTON BAY DSHD19574V10 Regan 21 Inch 3-Light Brushed Gold Vanity Light

with Clear Glass Shades

Product Information

• Item Numbers: 1004 335 702 / 313 853 291 / 1004 335 696 / 313 853 289 / 1006 320 957 316 719 920 / 1006 322 103 / 316 719 708 /1008 422 882
• Model Numbers: DS19267 / DS19268 / DSHD19574V2 / DSHD19574V6 /DSHD19574V10
• Product Type: 3-Light Vanity
• Manufacturer: Hampton Bay
• Customer Service Contact: 1-855-HD-HAMPTON
• Website: HAMPTONBAY.COM
• Warranty: Three (3) Year Warranty

Product Usage Instructions

Safety Information

1. Read and save the instructions provided in the manual.
2. Before assembling, installing, or operating the product,carefully read and understand all the information in the manual to ensure your safety.
3. Use a voltage tester to check if any wire is live before touching it.
4. Use tools with insulated handles and ladders made of wood.
5. Place safety covers over unused outlets to protect children.
6. Before repairing or removing any part of the product, disconnect the power by turning off the circuit breaker, removing the fuse, or tripping the breaker that controls the circuit.
7. Tape a sign to the panel warning others to leave the circuit alone while you work.
8. If you have any electrical questions, consult a qualified electrician. For non-electrical questions about the fixture, contact Hampton Bay Customer Service.

Warranty

The manufacturer provides a three (3) year warranty for this product. The warranty covers defects in materials and workmanship for three years from the date of purchase. The warranty applies only to the original consumer purchaser and products used in normal use and service. If the product is found to be defective, the manufacturer will repair or replace it at their discretion, provided that the product has not been damaged through misuse,abuse, accident, alteration, neglect, or mishandling. The warranty does not cover improper installation, setup, or use not following the supplied instructions. It also does not cover failures resulting from accidents, misuse, abuse, negligence, faulty installation, or any other failure unrelated to faulty material or workmanship. Normal wear and tear, such as surface and weathering, is not covered by the warranty.

Safety Information

READ AND SAVE THESE INSTRUCTIONS.

• □ For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install, or operate this product. Failure could be hazardous or even fatal.
  □ Before touching any wire, use a voltage tester to make sure it is not live.
  □ Use tools with insulated handles and ladders made of wood or
  □ To protect children, place a safety cover over any unused outlets.

DANGER: Befor re or removal of a pr re, disconnect the power by turning off the circuit breaker, removing the fuse at the fuse box, or tripping the breaker that controls that circuit. Tape a sign to the panel warning others to leave the circuit alone while you work.

CAUTION: CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS. If you have any
non-electrical questions about this fixture, please
call our Customer Service Team at 1-855-HD-HAMPTON or visit HAMPTONBAY.COM. Please reference the model and item numbers.

Warranty

THREE (3) YEAR WARRANTY

WHAT IS COVERED
The manufacturer warrants this fixture to be free from defects in materials and workmanship for a period of three (3) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alteration, neglect, or mishandling. This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship.
This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.

WHAT IS NOT COVERED
The manufacturer does not warrant and specifically disclaims any warranty, whether expressed or implied, of fitness for a particular purpose,other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product.

Pre-Installation

PLANNING INSTALLATION
Read all instructions before installing.
To avoid damaging this product, place it on a soft, non-abrasive surface, such as carpet or cardboard.

IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Please call the Customer Service Team at 1-855-HD-HAMPTON.

NOTE: You may use three Max 60W medium base (E26) type “ST64” or type “A” bulbs or three 9W medium base (E26) self-ballasted LED bulbs (sold separately).

TOOLS REQUIRED (NOT INCLUDED)

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

(Pre-assembled to bracket plate (A))

| 1
CC| Wire connector| 3
DD| Plastic anchor| 2
EE| Wood screw| 2
---|---|---
FF| Support screw (short)

(Pre-assembled to bracket plate (A))

| 4
GG| Thumbscrew| 9+2

PACKAGE CONTENTS

Installation

1. Preparing the bracket plate

   • Unscrew the four support screws (short) (FF) from the bracket plate (A). Remove the bracket plate (A) from the support screws (short) (FF) for later use.

2. Installing the bracket plate

   • Place the flat side of the bracket plate (A) against the wall and mark the location of the two key holes with a pencil (not provided).
   • Drill a small hole (6 mm) on each mark and push the plastic anchors (DD) into the wall using a hammer.
   • Fasten the bracket plate (A) onto the outlet box using the two outlet box screws (long) (AA). Place the two wood screws (EE) in the key holes located on the bracket plate (A) and tighten until fully secured.
     NOTE: If your wall is wood, do not drill holes. Use the two wood screws and two outlet box screws to secure the bracket plate.

3. Making the electrical connections

   • Strip 3/4 in. of insulation from the wire ends.
   • Connect the black wire from the fixture body (B) to the black wire from the outlet box, then connect the white wire from the fixture body (B) to the white wire from the outlet box.
   • The bare copper ground wire from the fixture must loop one turn under the head of the green ground screw (BB) on the bracket plat (A) before it is connected to the ground conductor of the supply circuit.
   • Cover and tighten the wires with wire connectors (CC). Tape the wire connectors (CC and wires together, and carefully position all wires inside the outlet box.

4. Attaching the fi xture body to the outlet box

   • Place the fixture body (B) against the outlet box, align the four holes of the bracket plate (A) and fixture body (B), then tighten the support screws (short) (FF).
   • There are two installation options to choose from.

5. Installing the glass shade to the fixture body

   • Place the glass shade (C) over the socket, align the three holes of the glass shade (C) and cap of the fixture body (B), then secure the glass shade with the thumbscrews (GG) as shown on the diagram.

6. Installing the light bulbs

   • Install the bulbs (not included) into the sockets. Use three Max 60W medium base (E26) type “ST64” bulbs.
     NOTE: You can also use three Max 60W medium base (E26) type “A” bulbs or Max 9W medium base (E26) self-ballasted LED bulbs (sold separately). Do not exceed the recommended wattage.

Care and Cleaning

• Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry, soft cloth to dust or wipe carefully.
• To clean the fi xture, disconnect power by turning off the circuit breaker or by removing the fuse at the fuse box. Use a dry or slightly dampened, clean cloth to wipe the exterior surface of the fi xture.

Troubleshooting

of the lamp. Check the wire connections. Contact a qualified electrician or call the Customer Care Service Team at 1-855-HD-HAMPTON.

Service Parts

MODEL: DS19267 / DS19268 / DSHD19574V2 / DSHD19574V6 / DSHD19574V10

(Pre-assembled to bracket plate (A))

CC| Wire connector
DD| Plastic anchor
EE| Wood screw
FF| Support screw (short)

(Pre-assembled to bracket plate (A))

---|---
GG| Thumbscrew
A| Bracket plate
B| Fixture body
C| Glass shade

Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service
8 a.m. – 7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday
1-855-HD-HAMPTON
HAMPTONBAY.COM
Retain this manual for future use.

HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.

References

• Hampton Bay - The Home Depot

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>