VISUAL COMFORT IKF 5362 Mafra XL Chandelier Instruction Manual

VISUAL COMFORT IKF 5362 Mafra XL Chandelier

Product Information

• Product Name : Mafra XL Chandelier
• Item Number: IKF 5362

Notice: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect items and contents carefully. If any damage or defect is found, do not install it. Retain all packaging material until installation is complete and approved.

Tools Required (Not Included):

• Phillips Screwdriver
• Wire Cutters
• Slotted Screwdriver
• Wire Strippers
• Measuring Tape

Persons Required: Two

Product Usage Instructions

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove mounting plate (D) from the canopy (E) by unscrewing.

3. Install mounting plate (D) to the junction box and secure it with mounting screws.

4. Connect driver (B) output neutral wire (black) to the fixture neutral wire (marked -) using wire nut (A).

5. Connect driver (B) output hot wire (red) to the fixture hot wire (marked +) using wire nut (A).

   • Caution: Do not reverse the hot and neutral connections.

6. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 2). Tighten.

   • Note: It is imperative that the fixture is grounded.

7. Connect driver (B) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).

8. Connect driver (B) input hot wire (black) to the supply hot
   wire (usually black) using wire nut (A).

   • Caution: Do not reverse the hot and neutral connections.

9. Make sure all wire connections are tight, then carefully tuck them into the junction box.

10. Install driver (B) into mounting plate bracket (D).

11. Thread canopy (E) to mounting plate (D).

12. Remove protective covers (H) from sockets.

13. Install LED bulbs (G) to sockets.

14. Thread shades (F) to fixture body (I).

    • Note: Do not overtighten otherwise shade could become damaged.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

ASSEMBLY INSTRUCTIONS

Mafra XL Chandelier
Item # IKF 5362

NOTICE:

This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED

(NOT INCLUDED):

• Phillips Screwdriver
• Slotted Screwdriver
• Measuring Tape
• Wire Cutters
• Wire Strippers
• PERSONS REQUIRED: Two

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (D) from canopy (E) by unscrewing.
3. Install mounting plate (D) to junction box and secure with mounting screws (C)
   • NOTE: It is recommended to have a helper assist in supporting the fixture for steps 4-5.
4. Feed hanging cables through canopy (E), then insert through holes on bottom of mounting plate (D).
5. Install cable locks (L) to end of hanging cables. Insert hanging cable through other end of locks and tighten ends (K) with screwdriver (J) to secure. See diagram 1.
6. Adjust hanging cables to desired height and level fixture.
   • NOTE: Double check height and ensure fixture is level before moving to next step.
7. Cut excess wires, being sure to leave enough to reach the junction box. Separate fixture wires (marked “+” & “-”) and strip insulation on each 5/8″.
   • NOTICE:
   • This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install it. Retain all packaging material until installation is complete and approved.
8. Connect driver (B) output neutral wire (black) to the fixture neutral wire (marked “-”) using wire nut (A)
9. Connect driver (B) output hot wire (red) to the fixture hot wire (marked “+”) using wire nut (A)
   • CAUTION: Do not reverse the hot and neutral connections.
10. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 2). Tighten.
    • NOTE: It is imperative that the fixture is grounded.
11. Connect driver (B) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A)
12. Connect driver (B) input hot wire (black) to the supply hot wire (usually black) using wire nut (A)
    • CAUTION: Do not reverse the hot and neutral connections.
13. Make sure all wire connections are tight, then carefully tuck into the junction box.
14. Install driver (B) into mounting plate bracket (D)
15. Thread canopy (E) to mounting plate (D).
16. Remove protective covers (H) from sockets.
17. Install LED bulbs (G) to sockets.
18. Thread shades (F) to fixture body (I)

• NOTE: Do not overtighten otherwise shade could become damaged
• Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>