OmniTrak 7591-04 PM plus tVOC-PID PPM Module User Guide

June 12, 2024
OmniTrak

OmniTrak 7591-04 PM plus tVOC-PID PPM Module

Product Information

The PM + tVOC-PID (PPM) Module, model 7591-04, is a handheld device that allows users to measure and analyze the conditions in their immediate area. It consists of a tVOC sensor and a PM sensor, providing immediate feedback on the concentration of various particles and pollutants.

The module is designed to be used in conjunction with the OmniTrakTM Smart Station, which enables users to take measurements, create reports, and analyze data to improve conditions. Please note that the module should not be worn on the body or placed near an individual’s head.

The package includes the device itself and a USB-C cable for charging purposes. The module is shipped in ‘Sleep Mode’ to protect the battery, and it needs to be charged for a few minutes before being powered on for the first time.

For disposal, please follow local rules and regulations regarding battery disposal.

Product Usage Instructions

  1. Power On: Hold down the power button on the left side of the module for 1 second.
  2. Power Off: Hold down the power button on the left side of the module until you see a light sequence of green, yellow, red. This indicates that the module is off.
  3. Charging: Plug the USB-C cable into the bottom of the module and connect it to a power source. A blinking green light will indicate that the module is charging.
  4. The module will appear in the list on the Smart Station. If it does not appear, click on “Refresh.”
  5. Press the desired module on the screen to connect it to the Smart Station. A green check mark will indicate a successful connection.
  6. Press “Done.”
  7. You are now ready to take measurements using the module.

Remember, the module needs to be charged for a few minutes before being powered on for the first time. Additionally, please comply with all safety guidelines and dispose of the battery properly according to local rules and regulations.

Operation Instructions

  1. Power On: Hold down power button on left side of module for 1 second.

  2. Power Off: Hold down power button on left side of module until you see a light sequence of green, yellow, red. That indicates module is off.

  3. Charging: Plug USB-C into bottom of module and into power source.
    A blinking green light indicates module is charging.

  4. Connecting to a Smart Station: Power on module by holding down the circle on the left for 1 second. A blue LED light will start to blink indicating Bluetooth® is on.

  5. The module will appear in the list on the Smart Station. If not, hit Refresh.

  6. Press desired module on screen to connect to Smart Station.
    A green check mark indicates a successful connection.

  7. Press Done
    Now you’re ready to take measurements.
    The OmniTrak™ Smart Station can be used in conjunction with any OmniTrak™ Module to provide immediate feedback as to the conditions in the immediate area. Take measurements, create reports, and analyze data provided to help improve conditions. This instrument is a handheld device, not to be worn on the body, or near an individual’s head.
    Dispose of battery in accordance with local rules and regulations.

What’s Included in the Box

  • Device
  • USB-C Cable

NOTE: All modules, by default, are shipped in ‘Sleep Mode’ to protect the battery. It will not be possible to power on the Module, using the side button, until ‘Sleep Mode’ is disabled. To disable, plug the module into a power source and charge the module for a few minutes.
This process is required only once.

DISCLAIMER
The tVOC measurement sensor is sensitive to radio frequency interference. Electromagnetic fields produced by items including, but not limited to, microwave ovens, Wi-Fi® routers, cellular phones, and personal communication devices, i.e., walkie-talkie, two-way radios, etc. have the potential to adversely affect the measurement.
To ensure a proper measurement these devices should be TURNED OFF or placed in a mode that does not transmit. If these devices are not turned off or placed in a mode that does not transmit, the accuracy of the measurement may be compromised if these devices are located within four meters of the sensor module.

Specifications

tVOC Sensor Specifications

  • Sensor Type PID (Photo Isonization Detector)
  • Range 0-2000 ppm
  • Resolution 0.1 ppm
  • Accuracy +/- (5ppm + 15% displayed value) ppm
  • Response Time < 10 seconds

PM Sensor Specifications

OmniTrak-7591-04-PM-plus-tVOC-PID-PPM-Module-1

AC and DC Power Requirements

  • AC/DC Power Supply 100 to 240 VAC,50/60 Hz, 0.3A
  • Device Input Power 5 VDC, 2A, 10W

Environmental/Installation Requirements

  • Maximum Altitude 3000 meters (10,000 feet)
  • Pollution Degree 2
  • Installation Category I
  • Operating Temperature 5°C to 40°C
  • Storage Temperature -20°C to 60°C
  • Humidity 0% – 95% (non-condensing)

Compliance

FCC ID:
2A22JOTMODULES
IC ID:
28101-OTMODULES
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:\

  1. This device may not cause harmful interference.
  2. T his device must accept any interference received, including interference that may cause undesired operation.
    Per FCC 15.21 Changes or modififications not expressly approved by TSI will void the product warranty and may void the user’s authority to operate the equipment.

Compliance
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development

Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. T his device must accept any interference, including interference that may cause undesired operation of the device.

WARNING

  • DO NOT attempt to replace the battery in this instrument.
  • DO NOT abuse the battery in any way as the battery may rupture or catch fire.
  • DO NOT use a substitute or nonrechargeable battery in this instrument.
  • DO NOT short-circuit, incinerate, dismantle or mutilate Lithium ion batteries
  • DO NOT expose to water or heat.
  • DO NOT use any battery which shows signs of damage, such as bulging, swelling, a swollen plastic wrap, liquid in the plastic wrap, etc.

LASER WARNING

  • OmniTrak™ Modules are Class 1 laser-based instruments.
  • During normal operation, you will not be exposed to laser radiation.
  • DO NOT open the OmniTrak™ Module when it is powered ON.
  • You will not be exposed to the laser radiation when the OmniTrak™ Module is disassembled.
  • The PM sensor has a laser inside it. DO NOT open the PM sensor inside OmniTrak Module when the OmniTrak Module is powered.

TSI Incorporated – Visit our website www.tsi.com for more information.

USA Tel: +1 800 874 2811
UK Tel: +44 149 4 459200
France Tel: +33 1 41 19 21 99
Germany Tel: +49 241 523030
India Tel: +91 80 67877200
China Tel: +86 10 8219 7688
Singapore Tel: +65 6595 6388
P/N 5003019 Rev B ©2023 TSI Incorporated Printed in U.S.A.

Specifications are subject to change without notice. Wi-Fi is a registered trademark of Wi-Fi Alliance®.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
TSI, and the TSI logo are registered trademarks of TSI Incorporated in the United States and may be protected under other country’s trademark registrations.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals