OmniTrak 7591-02 tVOC-PID PPM Module Instruction Manual

OmniTrak 7591-02 tVOC-PID PPM Module

Product Information

The tVOC-PID (PPM) Module, Model 7591-02, is a handheld device designed to measure total volatile organic compounds (tVOCs) using a photo-ionization detector (PID). It provides immediate feedback on the conditions in the immediate area and can be used in conjunction with the OmniTrakTM Smart Station to take measurements, create reports, and analyze data to improve conditions. The module is shipped in “Sleep Mode” to protect the battery and needs to be charged for a few minutes before it can be powered on using the side button. The module features a PID sensor with a range of 0-2000 ppm, a resolution of 0.1 ppm, an accuracy of +/-15%, and a response time of less than 10 seconds. The module can be powered using an AC/DC power supply with an input power of 100-240 VAC, 50/60 Hz, and 0.3A or a device input power of 5 VDC, 2A, and 10W. It has a maximum altitude limit of 3000 meters (10,000 feet), a pollution degree of 2, and an installation category of I. The operating temperature range is not specified, but the storage temperature should be within the specified humidity range of 0% – 95% (non-condensing). The device complies with FCC and IC regulations for operation and interference. It contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license- exempt RSS(s).

Product Usage Instructions

1. Power On: Hold down the power button on the left side of the module for 1 second.

2. Power Off: Hold down the power button on the left side of the module until you see a light sequence of green,
   yellow, red. This indicates that the module is off. Charging: Plug the USB-C cable into the bottom
   of the module and into a power source. A blinking green light indicates that the module is charging.

3. Connecting to Smart Station:

   • The module will appear in the list on the Smart Station. If it doesn’t, hit Refresh.
   • Press the desired module on the screen to connect to the Smart Station. A green check mark indicates a successful connection.
   • Press Done to complete the connection process.

4. Now you’re ready to take measurements using the tVOC-PID (PPM) Module.

Important Warnings:

• Do not attempt to replace the battery in this instrument.
• Do not abuse the battery in any way as it may rupture or catch fire.
• The module is a handheld device and should not be worn on the body or near an individual’s head.
• Dispose of the battery in accordance with local rules and regulations.

Operation Instructions

1. Power On: Hold down power button on left side of module for 1 second.
2. Power Off: Hold down power button on left side of module until you see a light sequence of green, yellow, red.
3. That indicates module is off.
4. Charging: Plug USB-C into bottom of module and into power source. A blinking green light indicates module is charging.
5. Connecting to a Smart Station: Power on module by holding down the circle on the left for 1 second. A blue LED light will start to blink indicating Bluetooth® is on.
6. The module will appear in the list on the Smart Station. If not, hit Refresh.
7. Press desired module on screen to connect to Smart Station. A green check mark indicates a successful connection.
8. Press Done

Now you’re ready to take measurements.
The OmniTrak™ Smart Station can be used in conjunction with any OmniTrak™ Module to provide immediate feedback as to the conditions in the immediate area. Take measurements, create reports, and analyze data provided to help improve conditions. This instrument is a handheld device, not to be worn on the body, or near an individual’s head.
Dispose of battery in accordance with local rules and regulations.

What’s Included in the Box

• Device
• USB-C Cable

NOTE : All modules, by default, are shipped in ‘Sleep Mode’ to protect the battery. It will not be possible to power on the Module, using the side button, until ‘Sleep Mode’ is disabled. To disable, plug the module into a power source and charge the module for a few minutes. This process is required only once.

Specification

Compliance

FCC ID:
2A22JOTMODULES
IC ID:
28101-OTMODULES

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Per FCC 15.21 Changes or modififications not expressly approved by TSI will void the product warranty and may void the user’s authority to operate the equipment.

Compliance

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

To satisfy RF exposure requirements, this device and its antenna may be operated near a persons body and the extremities, but must be operated with a separation distance of at least 20 cm from all person’s head.

WARNING

• DO NOT attempt to replace the battery in this instrument.
• DO NOT abuse the battery in any way as the battery may rupture or catch fire.
• DO NOT use a substitute or non-rechargeable battery in this instrument.
• DO NOT short-circuit, incinerate, dismantle or mutilate Lithium ion batteries
• DO NOT expose to water or heat.
• DO NOT use any battery which shows signs of damage, such as bulging, swelling, a swollen plastic wrap, liquid in the plastic wrap, etc.

DISCLAIMER
The tVOC measurement sensor is sensitive to radio frequency interference. Electromagnetic fields produced by items including, but not limited to, microwave ovens, Wi-Fi® routers, cellular phones, and personal communication devices, i.e., walkie-talkie, two- ay radios, etc. have the potential to adversely affect the measurement. To ensure a proper measurement these devices should be TURNED OFF or placed in a mode that does not transmit. If these devices are not turned off or placed in a mode that does not  ransmit, the accuracy of the measurement may be compromised if these devices are located within four meters of the sensor module.

TSI Incorporated – Visit our website www.tsi.com for more information

• USA Tel: +1 800 874 2811
• UK Tel: +44 149 4 459200
• France Tel: +33 1 41 19 21 99
• Germany Tel: +49 241 523030
• India Tel: +91 80 67877200
• China Tel: +86 10 8219 7688
• Singapore Tel: +65 6595 6388

P/N 5003018 Rev B ©2023 TSI Incorporated Printed in U.S.A.

Specifications are subject to change without notice.
Wi-Fi is a registered trademark of Wi-Fi Alliance®.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
TSI, and the TSI logo are registered trademarks of TSI Incorporated in the United States and may be protected under other country’s trademark registrations.

References

• Home | TSI

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>