CHLANT HM-1688 Head Shavers for Bald Men 7D User Guide

7D 5-in-1 Electric Shavers
Multifunctional Head Shaver Kit for Men
for personal facial shaving care
HM-1688 > 06h 

HM-1688 Head Shavers for Bald Men 7D

Notes
WARNING: Separate the handheld part from the power cord before cleaning the handheld part in water.

1. This product uses a USB charging cable.
2. You can use the 5V adapter mobile phone charger, or a USB interface of cars,computers and others for charging.
3. If the charging cable is damaged, replace it with a new one to avoid danger.
4. The product shall be charged and stored between5’C and 35’C.
5. Make sure the charge and charging cable are dry.Do not plug or unplug with wet hands to prevent electric shock.
6. Please check if the foil is damaged or deformed before use to avoid damage to your skin.
7. Clean the electric shaver head with clean water,please do not soak the whole body of the product in water long time.
8. Do not use salt water, hot water above 60°C, thinners, gasoline, alcohol or other chemicals to clean the electric shaver.
9. .its necessary to ensure to cover the electric shaver with the protective cover when you travel to protect its foil.
10. During the use and charging process,the electric shaver may be slightly heated. This is normal and please feel free to use it.
11. Please do not charge the electric shaver too long.
12. Do not store the electric shaver in direct sunlight or near other sources of heat.

How to Use

Charge

1. When the display shows “Available time,05 minutes”, the indicator light will flash, indicating that the battery is low-energy and needs charging (Fig. 1).
2. Plug the USB charging cable end into the electric shaver, then connect the USB cable to the charger and plug it into the power socket (Fig. 2),or plug the other end of the USB cable into a USB port of computers or cars.
3. When the power is turned on, the display will light up, with scrolling numbers which will increase as the charging time extends, indicating that it’s charging (Fig. 3).
4. Full charging takes about 1.5 hours on a continuous basis. After full charging, “FULL” and “90 min” will be displayed, indicating the shaver has been fully charged and can be used for about 90 minutes(Note:90 means a rough available duration instead of full charging until 100) (Fig. 4).

The LED display of this shaver can display available time, time of use and it will also remind you when need cleaning. A fully charged electric shaver can provide a shaving duration up to about 90 minutes, but the actual shaving duration may be less than expected due to differences in shaving habits, cleaning habits and beard types.
** The electric shaver can be used in the meanwhile it’s being charged by means of USB cable connection if it still has remaining energy.
How to Use **

Shave Beard and Head

Note: If the hair or beard is long, please use the hair trimmer to cut the hair to less than 3mm and then use the razor head to shave which can avoid pulling the hair.

1. Press the switch button to turn on the electric shaver(Fig.5).
2. Move the electric shaver foil against the growth direction of your beard on your skin and make straight and reciprocated movements (Fig. 6).
3. Hair on your neck can also be shaved (Fig. 7).
4. Before shaving your head, clean it with warm water and keep your hair dry. For a better effect of use, please use the cleaning brush if you need to clean the shaving head during the head shaving process, and wash the shaving head after shaving is completed (Fig. 7-1).

When shaving completed
Press the switch button again to turn off the electric shaver, air-dry it and then cover it with the protective cover to avoid damages to the foil.
Travel Lock

1. Press and hold the electric shaver switch button for 3 seconds, and then the electric shaver LED display indicates that the safety lock has been locked (Fig. 8).
2. Repeat the above step to unlock (Fig. 9). 

How to Use

Contents of Intelligent Display

1. When the electric shaver is overloaded, it will be automatically turned off, and the LED display will indicate stall protection. At this time, it should be cleaned up before use(Fig. 10).
2. When the faucet symbol flashes on the LED display,it indicates that the electric shaver needs to be cleaned(Fig. 11).

Wash and Clean with Water

1. Before cleaning, be sure to separate the electric shaver from the USB charging cable and press the switch to the off state.
2. Buckle up the middle groove of each shaving head, lift up and open the 6 round shaving blades, and then rotate the middle razor blade counterclockwise, pull it out (Fig. 12).
3. The electric shaver head can be washed directly under running tap (Fig. 13), but please do not soak whole body of the electric shaver in water for a long time.
4. After washing, drain any excessive water, put it horizontally and air-dry it. Do not wipe the shaving head part with tissue or cloth, which may cause damage.
5. First air-dry the electric shaver, then cover it with the protective cover to prevent damage to the foil1 and avoid accumulation of dust.

After the cutting head is dried, first put the middle little cutting head aim at the card slot, then rotate 15 degree in a clockwise direction, finally close the edge cutting heads in turn. (Fig. 14). Separate the handheld part from the power cord before cleaning the handheld part in water.

Operating Instructions for Hair Trimmer

Switch off the shaver, pull it up(not screw) to unload the shaving head,and insert the flange of the hair trimmer head part into the groove on the top of the shaver body. Then press down the hair trimmer head part to mount it on the shaver body (a click will be heard)(Fig. 15). Trim Note: Make sure your hair is clean and dry, and please don’t use the product for wet hair just washed.

1. Before trimming, first do remember to comb hair along its growth direction with a comb.
2. Mount the comb accessory into the slots on both sides of he product (a click will be heard) , and make sure it’s mounted correctly(Fig. 16).
3. The included combs are optional for different haircut lengths, such as 3mm, 5mm, and 7 mm, which can be mounted as required. To replace a comb, unload it from the groove on one side first(Fig.17).

Press the ON/OFF button and move the product slowly on hair. To get the best haircut effect, it’s necessary to move the product against the growth direction of hair. Clean

1. PuII out the hair trimmer head and clean the trimming part with the included cleaning brush or wash the hair trimmer head assembly with water.
2. Don’t clean the product with such liquids as abrasives, alcohol, petrol or acetone.
3. Clean the product immediately each time it’s used.

Operating Instructions for Nose & Ear Trimmer
Switch off the shaver,pull it up(not screw)to unload the shaving head, and insert the flange of the nose hair trimmer head part into the groove on the top of the shaver body. Then press down the nose hair trimmer head part to mount it on the shaver body (a click will be heard)( Fig. 18).
Trim Nose Hair

1. Make sure your nasal cavity is clean.
2. Start the ON/OFF button, insert the nose hair trimmer tip into one of your nasal cavities slowly and meanwhile tum the tip to remove overlong nose hair (Fig. 19).
3. The insertion depth of the tip into your nasal cavity must not exceed 0.5cm. To reduce pruritus, make sure that one side of the tip is firmly pressed against your skin.

Trim Ear Hair

1. Clean your extemal auditory canal to ensure there is no cerumen.
2. Start the ON/OFF button and then make the tip circle along your ear gently to remove protruding hair on your helix (Fig. 20).
3. Insert the ear hair trimmer tip into the external auditory canal carefully. The insertion depth of the tip into your auditory canal shall not exceed 0.5cm, or else your eardrum may be injured.

Clean Your Face with Facial Cleaner
Remove sebum and dirt on your face with the facial cleaner every day, which helps to keep your skin clean and health.

1. Make sure the device has been turned off and that the cleaning brush has been attached to the device(Fig. 21).
2. Moisten the facial cleaner with water. Do not clean your face directly with a dry facial cleaner, which may irritate your skin.

Package Included:

1 Main Body
1 Rotary shaver head
1 Hair trimmer head
1 Nose& ear trimmer head
1 Facial cleansing brush
1 Silicone massage brush
1 USB charging cable
1 Cleaning brush
3* Trimming combs(3mm/5mm/7mm)

Environmental Protection

1. To discard the product, please don’t put it together with general domestic rubbish heaps but hand it to the officially designated recycle center for the environmental protection(Fig.22).
2. The built-in rechargeable battery contains substances which may pollute the environment, so it must be unloaded from the product or sent to the officially designated recycle center to be disposed before it is discarded.

The battery should not be unloaded unless it has been used up .

1. Unplug the charger and also pull out the product’s plug from the shaver.
2. .Unload the battery. Do not plug in the shaver again after unloading the battery.

Model: HM-1688 Rated voltage: 3.7V
Rated power: 5W Input parameter: 5V ===( USB )
Charge: 1.5 hours Expend: 90 minutes

Documents / Resources

| CHLANT HM-1688 Head Shavers for Bald Men 7D [pdf] User Guide
HM-1688 Head Shavers for Bald Men 7D, HM-1688, Head Shavers for Bald Men 7D, for Bald Men 7D, Bald Men 7D
---|---
| CHLANT HM-1688 Head Shavers for Bald Men 7D [pdf] User Guide
HM-1688 Head Shavers for Bald Men 7D, HM-1688, HM-1688 Head Shavers, Head Shavers, Head Shavers for Bald Men 7D, Shavers for Bald Men 7D, Shavers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>