VISUAL COMFORT JN5330 Chalmette 11 Inch Layered Pendant Instruction Manual
- June 12, 2024
- VISUAL COMFORT
Table of Contents
VISUAL COMFORT JN5330 Chalmette 11 Inch Layered Pendant
Product Information
Product Name: Chalmette 11 Layered Pendant
Item Number: JN5330
Bulb: Bulb not included
Product Description
The Chalmette 11 Layered Pendant is a stylish and modern light fixture that adds a touch of elegance to any space. It features a layered design and comes with all the necessary components for installation.
Installation Notice
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction and
operation of it, as well as the hazards involved. Inspect the item and
contents carefully. If any damage or defect is found, do not install. Retain
all packaging material until installation is complete and approved.
Product Usage Instructions
- Carefully remove all parts from the box and place them on a clean, soft surface.
- Remove collar loop (D) from the chain (H) by removing the quick link (E).
- Install the mounting plate (B) to the junction box and secure it with the provided mounting screws (C).
- Secure the collar loop (D) to the mounting plate (B) using pliers to tighten the locknut.
- Install the canopy (F) to the collar loop (D) and secure it with the collar ring (G).
- Determine the desired overall length and amount of chain (H) needed. Shorten the chain using chain pliers, keeping the extra chain for future use.
- Attach the chain (H) to the collar loop (D) and the fixture loop (I) using quick links (E). Secure the quick links (E).
- Thread the fixture wire and ground wire through the chain (H). When reaching the collar loop (D), ensure there is no tension on the wires. Cut excess wires, leaving enough to reach the junction box.
- Separate the two sides of the molded wire and strip insulation on each end by 5/8 inch.
- Loosen the collar ring (G) and carefully let the canopy (F) slip down the chain (H).
- Twist all fixture wires together and slip them through the center hole of the collar loop (D). Untwist the wires and separate them to prepare for connection.
- Wrap the fixture ground wire (bare copper) around the green grounding screw and tighten it.
- Continue the fixture ground wire and connect it to the supply ground wire (usually green or bare copper) using a wire nut (A). It is imperative that the fixture is grounded.
- Connect the fixture neutral wire (ribbed) to the supply neutral wire (usually white) using a wire nut (A).
- Connect the fixture hot wire (smooth with markings) to the supply hot wire (usually black) using a wire nut (A). Make sure not to reverse the hot and neutral connections.
- Ensure all wire connections are tight, then carefully tuck them into the junction box.
- Install the canopy (F) to the collar loop (D) and secure it with the collar ring (G).
- Install a light bulb into the socket.
Care Instructions
Clean the light fixture only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
ASSEMBLY INSTRUCTIONS
Chalmette 11″ Layered Pendant
Item # JN5330
NOTICE:
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction and
operation of it, as well as the hazards involved. Inspect item and contents
carefully. If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.
TOOLS REQUIRED
(NOT INCLUDED):
- Phillips Screwdriver
- Slip Joint Pliers
- Wire Strippers
- Slotted Screwdriver
- Measuring Tape
- Chain Pliers
- Wire Cutters
-
Carefully remove all parts from the box. Place on a clean, soft surface.
-
Remove collar loop (D) from chain (H) by removing quick link (E).
-
Install mounting plate (B) to the junction box and secure with mounting screws (C).
-
Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut.
-
Install canopy (F) to collar loop (D) and secure with collar ring (G).
-
Determine desired overall length, and amount of chain (H) needed. Shorten chain using chain pliers. (Keep extra chain)
-
Attach chain (H) to collar loop (D) and fixture loop (I) using quick links (E). Secure quick links (E).
-
Thread fixture wire and ground wire through chain (H).
NOTE : When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box. -
Separate two sides of molded wire, and strip insulation on each 5/8″.
-
Loosen collar ring (G) and let canopy (F) slip down chain (H) carefully.
-
Twist all fixture wires together, and slip through center hole of collar loop (D).
NOTE: Untwist wires and separate to prepare for connection.
NOTICE :
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved. -
Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A).
NOTE: It is imperative that the fixture is grounded. -
Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).
-
Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections. -
Make sure all wire connections are tight, then carefully tuck into the junction box.
-
Install canopy (F) to collar loop (D) and secure with collar ring (G).
-
Install light bulb into the socket.
Care Instructions
Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>