HUAKUA V101 Smart HRm Bracelet User Guide
- June 4, 2024
- HUAKUA
Table of Contents
HUAKUA V101 Smart HRm Bracelet
Bind Watch
Download and install App.
You can set up the watch through the “WoFit” app for iOS orAndroid devices.
The steps are shown as follows: Notes: The hardware platform of the equipment
system shall meet requirements.I. Bind Watch
Bind process
- Turn on the Bluetooth and GPS on your mobile phone
- Bind Device
- Select product model: V101
- Click “Ok” to complete binding.
Notes:
- During binding process, WoFit will prompt you to enable GPS and Bluetooth, and authorize WoFit to get access to the GPS on you mobile phone.
- Apple phones need to click “pair”, the watch has a variety of message reminders.
- Synchronous dataIn daily wear, the watch can detect all kinds of product data. The user needs to connect the watch with bluetooth on the APP before synchronous operation. The detailed operations are shown as follows:
Product activation and installation
The product must be activated by charging before initial use, and then charge
the product to ensure normal power supply. The hand ring will automatically
power on.
Take out: Pull open the strap and take out the bracelet body Open the mobile
APP> swipe down thepage> sync prompt appears
Notes!Please synchronize the data at least once within 5 days to avoid data
loss at the watch end.
Charge the battery: Insert the chip-mounted end of the bracelet body into the USB interface to activate the product by charging (be cautious not to reverse the polarity, and comply with the required voltage and current: 5V / 500mA)
Installation: Mount the bracelet body into the slot of the wrist strap.
Wear on: Adjust the length of the wrist strap until it is appropriate to wear on the wirst.
Touch key
- Slide the touch key: Interface switch Press and hold the touch key: Enter
Know your Device
-
Wearing Method
Wear the device on your wrist horizontally, about 2cm to carpal,the same method as wearing watches. -
Heart Rate Monitoring
To monitor Heart Rate more accurately, please wear the device on the upper position of your wrist and a bit tighter than usual when you are taking exercise. -
Heart Rate Monitoring
Automatic heart rate Monitoring is ON as default, monitor Heart Rate all the day automatically. -
Interface
Click the touch key to display successively
-
Watch dial switch
The watch supports to switch among 5 dials. Long press on the main interface
of the watch to switch the dial. 
Note: Cloud dial and custom dial can be set in the APP.
Function Introduction
-
Data Mode
Instructions
Time dial can be switched as follows:
APP Devices Mode>More
[Slide the touch key] to enter the next mode: Data Mode -
Step Mode
[Slide the touch key] to enter the next mode -
Distance Mode
[Slide the touch key] to enter the next sub-mode -
Heart Rate Mode
Note: Upon staying at the Heart Rate interface for 1s, start to monitor the heart rate, and a fig. like is displayed before the correct data is monitored, and upon the correct data being monitored, data is displayed.[Click the touch key] to enter the next mode: Alarm Clock Mode -
Sleep Data
The watch can automatically test the sleep data every day. Please wear the watch well before sleepingAt the end of the day, sleep time and sleep status are displayed. -
Message
Display notification message content
Note: Set up message notification after connecting to the APP -
More
-
Sports Mode
[Press and hold the touch key for 2s] to enter the
Sports Mode
[Click the touch key] to enter the next sports mode; and in case there are no other sports modes, it will go back to the time mode.
Note: Types of Sports mode can be selected in App (App can handle 3 types of track recording sports and 6 types of other activities) -
Sports Start Mode
After the countdown interface of 3-2-1 is the sports underway mode. -
Sports Underway Mode
[Click the touch key] to enter the next sub-mode of “Sports Underway”[Press
and hold the touch key for 2s] to enter any interface of Data Reading, press
and hold 2s to exit the sports mode.
Note: The speed and distance of riding can be displayed, but App need to be
connected and the riding and App needs to start at the same time.
Basic Specifications
- Model No.: V101
- Battery Capacity: 90mAh
- Working Voltage: 4.35V
- Host weight: about 24.8g
- Sync: Bluetooth 4.0
- Working temperature: －20℃- 40℃
- Waterproof: IP68
- Working Time: 7days
- Product frequency band: 2402-2480MHz
- Maximum transmit power: -3.18dBm
Declaration of toxic and hazardous substances in electronic information products
The device meets the EU ROHS criterion. Please refer to IEC 62321, EU ROHS Directive 2011/65/EU and revised directive.
Wearing and Maintenance
Our products are designed for you to wear throughout the day. So please follow a few brief instructions when you are wearing and maintaining your smart devices. To keep your wristband clean and your skin comfortable, we put forward the following tips:
- Regularly clean your wrist and the smart wristband, especially after sweating in the exercise or being exposed to substances such as soap or detergent which may attach on the internal side of the wristband.
- Do not wash the wristband with household cleanser.Please use soapless detergent, rinse thoroughly and wipe with a piece of soft towel or napkin.
- For spots or stains that are not easy to remove, scrub with alcohol and then follow the above steps.
FAQ
Failed to find the device when pairing
- Make sure the Bluetooth of smartphone is ON, and smartphone OS Android 4.4 & Above, iOS 8.0 & Above.
- Make sure the distance between phone and device is within 0.5meter, device is among the normal Bluetooth communication distance range(within 10meter) after pairing finished.
- Make sure the device is not under low battery. If there is still a problem after fully charged, please contact us.
Failed to connect with Bluetooth occasionally
- Caused by the abnormality of Bluetooth service when it restarted on the phone.
- Reboot mobile phone or re-start the Bluetooth service, then it works normal.
FCC Rules
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.