VeEX MTTplus-523 Module Software Updates User Guide
- June 12, 2024
- VeEX
Table of Contents
VeEX MTTplus-523 Module Software Updates User Guide
Release Scope:
Major Release. Limited Availability.
Requires MTTplus Platform version 03.00.0000 or higher
Features and improvements:
- Required for compatibility with new major MTTplus Platform release 03.00.xxxx to support newer and faster host CPU in newly-shipped MTTplus platforms.
- Now supports results transfer with ReVeal RXTS.
Known issues or limitations:
- This release is limited to new MTTplus Platforms shipped since January 2022. This version is currently under regression and beta testing for platforms shipped prior to 2021. DO NOT downgrade factory-installed 03.00.xxxx versions to 02.xx.xxxx, unless specifically instructed by our Customer Support team!.
- Module hot swap is not supported. A new module will be detected upon power up.
Release Scope:
General availability.
Requires MTTplus Platform version 02.00.0000 or higher
Features and improvements:
- Added INP Control setting in the Setup tab.
Known issues or limitations:
- Module hot swap is not supported. A new module will be detected upon power up.
Release Scope:
General availability.
Requires MTTplus Platform version 02.00.0000 or higher
Features and improvements:
- Required version for compatibility with MTTplus Platform version 02.00.0000 or later versions.
Known issues or limitations:
- Module hot swap is not supported. A new module will be detected upon power up.
Release Scope:
Initial Release. General availability.
Requires MTTplus Platform version 01.00.0079 or higher
Features and improvements:
- Initial Release.
Known issues or limitations:
- Module hot swap is not supported. A new module will be detected upon power up.
References
Test Profiles and Test Results Backup Procedure
Warning: Before upgrading the platform or module software, it is
recommended you back up all test results and profiles to avoid this data being
lost during the upgrade process. The software upgrade process clears all user
data stored in the unit.
The MTTplus Platform File Management system offers backup [To USB] and restore [From USB] functions to preserve User data. This function is located in the Utilities >Files >Saved system – see the left side of the screen.
To enable the [To USB] and [From USB] functions, insert a USB Memory stick (FAT32 file format) into a USB port on the side of the unit. Do not remove the micro USB drive located on the top slot. Wait for the USB memory to be detected (the folder icon will change appearance with a green USB memory icon).
Select the desired test results, test profiles, screen capture and protocol
capture files to be saved, using the individual check boxes. For a full
backup, check the master check box on the header and all files will be marked.
Tap the [To USB] button to initiate the file transfer procedure and wait for
the progress bar to finish. Original files won’t be deleted from the test set.
When all files have been copied to the USB, tap the folder icon (top-right corner) and select “Remove USB Drive” to make sure all cached data is transferred to the USB drive, especially when transferring small files.
Once the unit has been updated, you can use the [From USB] function to restore the test data and profiles back onto the test set.
Updating the MTTplus Platform System Software (via USB)
Warning: The system update procedure reformats the platform’s internal
storage and all results and profiles are erased. Please follow the procedure
above to save all important files prior to updating the system software. Once
you have obtained and uncompressed the update package file (mttplus-veex-
arm.tar.gz), the firmware update procedure can be performed using a FAT32 USB
Memory stick.
Note: If installed in your PC, some file compression agents (applications) may show the resulting mttplus-veex-arm.tar.gz as a compressed file, but there is no need to expand the file any more. Keep it as is.
- Copy the uncompressed file to the root of the memory stick
- Plug the memory stick into one of the MTTplus platform’s USB ports (use a USB-A OTG adapter for the microUSB-B, if necessary)
- Turn the power OFF and remove test module.
- Press the (Camera) and (Power) buttons simultaneously. The two buttons can be released once the confirmation tone (beep) is heard. The system update procedure starts.
- The update process would take a few minutes and the RXT will reboot itself at the end.
The MTTplus must be connected to AC/DC charger at all times during the upgrade
process. DO NOT turn it off at any time. To verify the current software
version installed in the unit, open the Utilities section, select Settings,
and open About. Test modules may need to be updated to their latest software
version available, to ensure full compatibility.
Updating the MTTplus Platform System Software using VeExpress (Internet)
Connect the unit to the internet, then go to >Utilities >VnExpress and press
Check to connect to the VeExpress server and see if there is a new SW update
(Delta Push) or full upgrade (via USB memory) available. If available, the
built-in DevExpress client can perform consecutive (incremental) updates
directly from the MTTplus Platform (for example, updating from 1.0.1 to
1.0.2). The advantage is that update packages are smaller and faster to
download. The test set must be connected to a LAN (using the Management port)
and have access to the Internet. If the current SW is much older for a delta
push, then the MTTplus will instruct you download the full install package
from www.v-express.com or
www.veexinc.com and perform the USB Upgrade
procedure described earlier. The test set can also download the full upgrade
package to an attached USB memory stick (no PC required).
Updating Native Test Module Software (via USB)
Note: Certain test modules may use different software update procedures.
Please check the specific module documentation or Software Release Notes for
details.
Please ensure the MTTplus Platform is running the latest firmware version
available.
- Copy the test module’s uncompressed firmware update package file to the root of the memory stick
- Plug it into one of the MTTplus platform’s USB ports
- Turn the power OFF and insert the appropriate test module (if not already inserted).
- Turn the MTTplus Platform ON and wait for the boot up process to finish.
- The MTTplus may display an “incompatible software version” warning message to indicate that the test module requires a firmware update. Tap the OK button to close the message.
- Touch the V or Utilities button on the top bar, open the Utilities tab on the left bar, and select M.Upgrade.
- The MTTplus will search the memory stick for valid update packages and show its information.
- Tap on the Upgrade button to start the firmware update process – This could take several minutes depending on module type. The MTTplus will shut down once the upgrade is complete.
The MTTplus must be connected to AC/DC charger at all times during the whole upgrade process. DO NOT turn it off at any time; the update process would take a few minutes and the MTTplus will reboot itself at the end. To verify the software version number installed in the current test module, turn the MTTplus back on, open the Utilities section, select Settings, and open About. The firmware update package files for multiple modules can be copied into a USB memory stick at once, but each module must be updated separately, by plugging one module at a time, following the procedure listed above.
© 2022 VeEX Inc. All rights reserved.
VeEX, VePAL, RXT, MTTplus, ReVeal, VeExpress, V-SAM, Multi-BERT, V logos,
Sunrise Telecom, SunSet, and MTT are trademarks or registered trademarks of
VeEX Incorporated, or one of its affiliates. All other trademarks or
registered trademarks are the property of their respective owners. Some
features listed in this document require software options that may require
paid activation or license, and may or may not be available in all products.
VeEX Inc., reserves the right to change, without notice, product offerings or
specifications.
2827 Lakeview Court, Fremont, CA 94538, USA
Tel: 1.510.651.0500
Fax: 1.510.651.0505
Web: www.veexinc.com
References
- Untitled Page
- Untitled Page
- VeEX Inc. | The Verification EXperts
- VeEX Inc. | The Verification EXperts
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>