BATTLE BORN BB10012 100Ah 12V LiFePO4 Deep Cycle Battery Installation Guide
- June 4, 2024
- BATTLE BORN
Table of Contents
- BB10012 100Ah 12V LiFePO4 Deep Cycle Battery
- What is in the Box?
- What Do I Need for Installation?
- Connecting Load Specified Cables to the Batteries
- Connecting the Batteries in Parallel
- Connecting the Batteries in Series
- Voltage vs. Capacity
- Warranty
- WARRANTY EXCLUSIONS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Battle Born Batteries BB10012 | BB10012H Manual
Model BB10012 I BB10012H
BB10012 100Ah 12V LiFePO4 Deep Cycle Battery
Manual and Installation Guide
Dragonfly Energy Corp.
Please read this manual prior to installation and use.
Thank you for investing in a Battle Born Batteries system and welcome to the
Battle Born Batteries family. This manual provides important information on
how to install, perate, and care for your Battle Born Batteries. If you have
purchased with us before, you will find this manual useful as a reference
tool. If this is your first purchase with Battle
Born Batteries, this manual can serve as an educational tool on how to
properly use and care for your investment. If you have a heat-enabled model,
please refer to the additional Heat-Enable Instruction manual prior to use and
installation.
QR Codes will appear throughout the manual linking to FAQ videos that may
be useful.
To use the QR code, open a QR reader or the camera on your smartphone. Hold
your device over the QR code so that the code is clearly visible within the
device’s screen. Your phone will automatically scan the code and pull in the
corresponding web link.
**** Caution: Risk of Fire and Burns. Do Not Open, Crush,
Heat Above 150ºF, or incinerate. Follow the Manufacturer’s Instructions.
****Attention, Risque d’incendie et de brulures. Veuillez ne pas ouvrir, percer, ou exposez à une chaleur égal ou supérieur à 66º C. Ne pas mettre dans le feu. Veuillez suivre les instructions du fabricant.
What is in the Box?
Included with every purchase of a Battle Born Battery is:
- (1) BB10012/H Battle Born Battery
- Dimensions (L x W x H): 12.76” x 6.86” x 8.95”
- Weight: 31 lbs.
- Operating Temp Range: 4°F (-20°C) to 135°F (57.2°C)
- Water Resistant and Sealed (Batteries should not be submerged)
- Built-in BMS (Battery Management System)
- Made with Cylindrical Cells
- Comes with standard flag-style terminal posts with a 3/8” hole to accommodate either a 3/8” or a 5/16” bolt https://battlebornbatteries.com/wp-content/uploads/2019/01/10012.pdf
- (1) Finishing Hardware Kit
- (2) ‘18-8 Stainless Steel’ 5/16-18 x 1” Bolts
- (2) ‘18-8 Stainless Steel’ 5/16-18 x 1 1/4” Bolts
- (4) Washers
- (2) Nylok Nuts
https://battlebornbatteries.com/wp-content/uploads/2020/11/BB10012H.pdf
What Do I Need for Installation?
If you already have your system set up and are ready to drop in your batteries, you will need a torque wrench that is able to fit to and properly torque your 5/16” finishing hardware. This is REQUIRED to make sure that you torque to the specification of 9 to 11 ft-lbs., otherwise, you may cause system failures and damage.
Connecting Load Specified Cables to the Batteries
-
Identify the positive and negative terminals. These are labeled and color-coded red for positive (+), and black for negative (–).
-
Determine which finishing hardware set you will use. Verify that your bolt can fully seat into the nylon insert of the nut. If multiple lugs are used, longer bolts may be required for the bolt to fully seat into the nylon insert of the nut.
-
Connect your cable lugs to your battery terminal with the previously identified finishing hardware set. Make sure to connect your positive load-specified cable lug to the positive terminal and the negative load-specified cable lug to the negative terminal. The proper order to connect to your terminal with a finishing kit is shown in Fig. 1.
-
When connecting to your battery terminals, DO NOT finger tighten. Use a torque wrench to torque your hardware to the specification of 9 to 11 ft-lbs. Failure to adequately secure connections can result in severe damage and will void your warranty. Fig. 2 below demonstrates proper and improper connections.
Connecting the Batteries in Parallel
Why Connect in Parallel?
Multiple BB10012|BB10012H batteries may be connected in parallel to increase
the capacity and current of the system when batteries are connected in
parallel, the voltage of the system does not change, but the capacity and
current limiare additive. For example, two BB10012|BB10012H batteries
connected in parallel (shown in Fig. 3) create a 12V 200Ahbank that can
deliver 200A continuously and 400A for 30 seconds.
Multiple BB10012|BB10012H batteries may be connected in parallel to increase
the capacity and current of the system. When batteries are connected in
parallel, the voltage of the system does not change, but the capacity and
current limit are additive. For example, two BB10012|BB10012H batteries
connected in parallel (shown in Fig. 3) create a 12V 200Ahbank that can
deliver 200A continuously and 400A for 30 seconds.
How to Make a Parallel Connection
NOTE: All cables and connections MUST be able to accommodate the high
currents that can be delivered by the battery. Appropriate fuses and circuit
breakers are highly recommended to protect downstream components from current
spikes and short circuits.
- Identify the positive and negative terminals. These are labeled and color-coded red for positive (+), and black for negative (–).
- Determine the appropriate finishing hardware set you will use. Verify that your bolt can fully seat into the nylon insert of the nut. If multiple lugs are used, longer bolts may be required for the bolt to fully seat into the nylon insert of the nut.
- Make the proper cable connections to the positive of the first battery. Please reference Fig. 1 for the proper order of hardware.
- When connecting to your battery terminals, DO NOT finger tighten. Use a torque wrench to torque your hardware to the specification of 9 to 11 ft-lbs. Failure to adequately secure connections can result in severe damage and will void your warranty.
- Connect the other end of your positive cable to the positive terminal of the other battery you are connecting to. Repeat step 4.
- Repeat steps 3-5 for the negative connections.
- Repeat steps 3-6 for additional batteries in the system. An example of a finished connection can be found below in Fig. 3.
Connecting the Batteries in Series
Why Connect in Series?
When batteries are connected in series, current capacities remain the same,
but the system voltage is additive. For example, two BB10012|BB10012H
batteries connected in series form a 24V 100Ah bank (shown in Fig. 4) and
should be charged using a bulk and absorption voltage of 28.8V, and a float
voltage of 27.2V.
How to Make a Series Connection
Note: Battle Born 10012|10012H Batteries are capable of being connected
in series up to 48V. DO NOT exceed a 48V setup or you will void the batteries’
warranty.
-
Before making any connections, make sure to charge each battery up to 14.2V – 14.6V with a proper lithium charger.
ALL BATTERIES SHOULD BE AT THE SAME STATE OF CHARGE PRIOR TO CONNECTING, otherwise you will encounter balance issues within your system. You can check your battery’s state of charge with a multimeter. -
Identify the positive and negative terminals. These are labeled and color-coded red for positive (+), and black for negative (–).
-
Determine the appropriate finishing hardware set you will use. Verify that your bolt can fully seat into the nylon insert of the nut. If multiple lugs are used, longer bolts may be required for the bolt to fully seat into the nylon insert of the nut.
-
Make the proper cable connections to the negative of the first battery. Please reference Fig. 1 for the proper order of hardware.
-
When connecting to your battery terminals, DO NOT finger tighten. Use a torque wrench to torque your hardware to the specification of 9 to 11 ft-lbs. Failure to adequately secure connections can result in severe damage and will void your warranty.
-
Connect the other end of your cable to the positive terminal of the other battery you are connecting to. Repeat step 4.
-
Repeat steps 3-6 for additional batteries, but DO NOT exceed 48V. An example of a correct series connection can be found below in Fig. 4.
How to Properly Charge the Batteries
To properly charge your Battle Born batteries, you will want to verify that
any charging component in your system is capable of being programmed for the
following specifications. Charging components can include, but are not limited
to converters, inverter chargers, solar charge controllers, DC-to-DC chargers,
etc.
- Bulk/Absorption: 14.2V – 14.6V
- Absorption Time: 30 minutes per battery (for parallel string)
- Float: 13.4V – 13.8V
- Equalization: 14.4V/ Disabled
- Temperature Compensation: 0/Disabled
- Charge Rate: .5c
- Battery Charge Temperature Range: 25°F (-3°C) to 135°F (57.2°C)
- Battery Discharge Temperature Range: -4°F (-20°C) to 135°F (57.2°C)
- Cell Charge Temperature: 32°F (0°C) to 131°F (55°C)
- Cell Discharge Temperature: 68°F (20°C) to 140°F (60°C)
NOTE: Not all chargers are capable of multistage charging. If yours is not, you will want to verify it can be programmed for the Bulk/Absorption voltage and have the other items mentioned are disabled if applicable. Consult your charger’s manual or the manufacturer.
How Does the BMS Protect the Batteries?
All Battle Born Batteries come with a built-in battery management system (BMS)
that protects the cells from many strenuous circumstances to protect the life
cycles of the cells and your electrical system from potential damage. The BMS
in the BB10012 | BB10012H allows for 100 Amps continuous, 200 Amp surge for 30
seconds, and 1/2 second surge for loads over 200 Amps. All of our BMS’ protect
against the following conditions:
High Voltage Disconnect ( > 14.7V)
If an individual cell voltage exceeds a prescribed threshold during charging,
the BMS will prevent a charge current from continuing. Discharge is always
allowed under this condition. If the batteries have not been balanced for a
long time, high voltage disconnect could occur at a lower voltage. The
batteries will rebalance after several full charges.
Low Voltage Disconnect ( < 10.6V)
If an individual cell falls below a prescribed threshold during discharge, the
BMS will prevent further discharge. Although the battery is in “low-voltage
disconnect” mode, it will still allow a charging current.
NOTE: Many chargers must detect a voltage over 10V to send a charge to
the battery. Please be aware that some chargers may not sense a battery in low
voltage disconnect and you may need to jump it with a 12V source to “wake up”
the battery. You should jump your battery within 24hrs of entering the low
voltage disconnect otherwise you risk damaging your battery and voiding the
warranty. High Temperature Charging and Discharging (> 135°F/57.2°C) The BMS
will not allow charging or discharging current if the internal temperature of
the battery has reached 135°F (57.2°C).
Low-Temperature Charging ( < 25°F/-3.9°C)
The BMS will not allow a charging current under 25°F (-3.9°C) but will
continue to discharge down to -4°F (-20°C).
NOTE: The BB10012|BB10012H has an operating temperature range of -4°F
(-20°C) to 135°F (57.2°C).
High Current Discharge Surges
The BMS will not allow a current that exceeds 200 (+/- 5%) Amps for more than
30s, or anything larger for 0.5s. After a
high current disconnection, the battery will automatically reconnect after 5
seconds.
Short Current Discharge Surges
Our BMS has built-in short circuit protection. If the short circuit protection
is tripped, the BMS will shut the battery down and will remain disconnected
until you remove the battery cables. While the battery cables are
disconnected, we suggest taking the voltage of the battery with a voltmeter.
If it reads above 10V, reconnect the battery cables. If you are unsuccessful
at obtaining a voltage reading above 10V, please give our technical support
team a call.
Balancing of Cells
A passive balancing process is activated by the BMS at the top of each charge
cycle when the battery voltage exceeds 14.2V. This ensures that all the cells
remain at the same state of charge, which helps pack longevity and
performance.
Voltage vs. Capacity
For A Single Battery
How to Properly Size Cables for a System Install
When considering cable sizing there are a few factors to consider. First, what
is the size of the load you are powering with the battery bank? Second, how
far away from the battery is the load? You can do voltage drop calculations
to see if you need to step up your cable size. Fig. 5 is a chart to use for
reference. Do keep in mind that cables are only capable of carrying a certain
amperage and you should verify the specifications of your cable and the power
draws before implementing them into your system to avoid potential failures
and damage.
https://www.youtube.com/watchv=qHi2AGrfO_0&t=2s
How to Incorporate Fuses into System Install
ANL fuses are designed to melt and separate into two pieces for the purpose of
breaking a circuit in the event of excessive current. These fuses are
essential components for protection against a catastrophic event and are
typically placed between Battle Born Batteries and the inverter/load.
https://battlebornbatteries.com/why-should-you-invest-in-fuses-for-your- system/
How to Properly Store Batterie s
We recommend bringing the Battle Born batteries to a 100% state of charge.
Then, disconnect the battery from any loads by removing the negative cable
from one battery. On average, the batteries lose approximately 2-3% capacity
per month. This is subject to increase if stored in extreme environmental
conditions.
https://battlebornbatteries.com/faq-how-to-winterize-your-batteries/
How to Maintain the Batteries
Battle Born Batteries require very little maintenance. If your batteries are
in series and not being charged by a multi-bank charger it is recommended that
you fully charge the batteries individually once a month if the system is
used frequently. This will internally balance your batteries to ensure that
they will reach their expected life span and allow you to get the full power
out of them with each use. If your batteries are in parallel this is not
necessary, just make sure the batteries are charged to 14.2V – 14.6V
frequently for internal balance. Our BMS has a built-in passive balancing
system that will take care of this for you.
For more FAQs scan the QR code.
https://battlebornbatteries.com/faq/
https://battlebornbatteries.com/product-category/lifepo4-batteries/
To see what else Battle Born Batteries has to offer, scan the QR code to the
right or visit https://battlebornbatteries.com/shop/
How to Properly Recycle and Dispose of the Batteries
Here at Dragonfly Energy, our goal is to provide our customers with long-
lasting green energy that will support them for years on all their adventures.
That is why we not only build batteries that can keep up with you for a long
time but also provide industry-leading customer support to help you get the
most out of your batteries. When the time does come and your batteries have
reached the end of their life it is important to recycle them responsibly.
Here are a few suggestions:
- Make sure all loads are removed from your system before removing the batteries. Once the batteries are removed cover the terminals using electrical tape. Now can be a good time to inspect any cable runs or lugs.
- Visit www.earth911.com or www.call2recycle.org/locator to find a drop-off location. Be sure to call ahead of time to confirm that the drop-off location is still accepting materials.
- Give us a call if you are having any trouble finding a drop-off location and we can help you find one.
Warranty
Dragonfly Energy Corp. (“the Manufacturer”) warrants each Dragonfly Energy and
Battle Born Batteries branded Li-ion battery (“the Product”) sold by Dragonfly
Energy, Battle Born Batteries, or any of its authorized distributors or
dealers, to be free of defects for a period of 10 years (“the Warranty
Period”) from the date of sale as determined by either the customer’s sale
receipt, the shipping invoice, and the battery serial number, with proof of
purchase. Within the first 8 years of the Warranty Period, subject to the
exclusions listed below, the Manufacturer will credit, replace, or repair, if
serviceable, the Product and/or parts of the Product if the components in
question are determined to be defective in material or workmanship. After 8
years and up to 10 years, if the components in question are determined to be
defective in material or workmanship, and the Manufacturer deems the
components to be repairable, the Product will be repaired and returned. If the
Manufacturer deems the components to be not repairable, a new,
similar Product will be offered at a discount of 30% off the price listed at
the time of the offer. The offer will be valid for a period of
30 days after the date of notification. See https://battlebornbatteries.com
/terms-conditions/#warranty for the full warranty policy.
NON-TRANSFERABLE
This Limited Warranty is to the original purchaser of the Product and is not
transferable to any other person or entity. Please contact the place of
purchase regarding any warranty claim.
WARRANTY EXCLUSIONS
The Manufacturer has no obligation under this Limited Warranty for the Product subject to the following conditions (including but not limited to):
-
Damage due to improper installation; loose terminal connections, under-sized cabling, incorrect connections (series and parallel) for desired voltage and AH requirements, or reverse polarity connections.
-
Environmental damage: inappropriate storage conditions as defined by the Manufacturer; exposure to extreme hot or cold temperatures, fire or freezing, or water damage.
-
Damage caused by collision.
-
Damage due to improper maintenance, under or over-charging the Product, dirty terminal connections.
-
The product that has been opened, modified, or tampered with.
-
The product that was used for applications other than which it was designed and intended for, including repeated engine starting.
-
The product that was used on an oversized inverter/charger (any inverter/charger that is rated to 3500 Watts or greater) without
the use of a Manufacturer-approved current surge limiting device. -
The product that was under-sized for the application, including an Air Conditioner or similar device having a locked rotor start-up current that is not used in conjunction with a Manufacturer-approved surge-limiting device.
-
Product not stored in adherence to the Manufacturer’s storage guidelines, including storage of the Product at a low state of charge.
This Limited Warranty does not cover a Product that has reached its normal end of life due to usage which may occur prior to the Warranty Period. A battery can deliver only a fixed amount of energy over its life which will occur over different periods of time depending on the application. The Manufacturer reserves the right to deny a warranty claim if the Product is determined, upon inspection, to be at its normal end of life even if within the Warranty Period. Please see https://battlebornbatteries.com/terms- conditions/#warranty for the full warranty policy or scan the warranty QR code.
https://battlebornbatteries.com/terms-conditions/#warranty
Return Policy
You have 30 calendar days to return an item from the invoice date. To be
eligible for a return, your item must be in the same condition that you
received it in. You must have the receipt or proof of purchase. If an item is
new, unused, and in the original packaging, we are happy to accept a return up
to 30 days from the original invoice date with no restocking fee. The item
must be returned with its original packaging. Original packaging must be in
the same condition as it was received, otherwise, you may be responsible for a
restocking fee. If the item has been installed, used, or no longer has the
original packaging, we will assess a restocking fee that will be shared when
the return merchandise authorization (RMA) is issued. Items 60 days past the
original invoice will be reviewed at Battle Born’s discretion.
Returns will not be accepted without an RMA number, which can be obtained by
filling out the return form at https://battlebornbatteries.com/returns/. To
avoid being charged restocking fees, review the full return/refund policy at
https://battlebornbatteries.com/terms-conditions/#warranty.
Refund Policy
You have 30 calendar days to return an item from the invoice date. Once we
receive your item, we will inspect it and notify you that we have received
your returned item. We will immediately notify you of the status of your
refund after inspecting the item. If your return is approved, we will initiate
a refund to your credit card (or original method of payment). You will receive
the credit within a certain amount of days, depending on your card issuer’s
policies. No refund is guaranteed after the initial 30 days have passed or if
the item has been used.
Shipping
You will be responsible for paying for your own shipping costs for returning
your item. If you are returning prior to 30 days from the original ship date,
you may be eligible for a free return. In order to be eligible for free
shipping, you MUST have the original packing in which the order was shipped,
including boxes, foam, wrapping, and pallets if necessary. Not all items will
be eligible for free return shipping. Shipping costs are non-refundable. If
you receive a refund, the cost of return shipping may be deducted from
your refund. If you have any questions, please contact us by calling
855-292-2831 or emailing us at
info@battlebornbatteries.com.
Notice: Product improvements and enhancements are continuous; therefore,
the specifications and information contained in this document may change
without notice. Dragonfly Energy Corp. shall not be liable for errors
contained herein or for incidental or consequential damages in connection with
the furnishing, performance, or use of this material. No part of this document
may be photocopied, reproduced, or translated to another language without the
prior written consent of Dragonfly Energy Corp.
Copyright © 2021, Dragonfly Energy Corp., all rights reserved. Battle Born
Batteries® is a registered trademark of Dragonfly Energy Corp. All other
trademarks, trade names, service marks, and logos referenced herein belong to
their respective owner.
References
- VRM Portal - Victron Energy
- Battery & Cellphone Drop-Off Locations | Call2Recycle
- Earth911 - More Ideas, Less Waste
- Battle Born Batteries | Reliable Lithium-Ion Batteries
- Terms & Conditions | Battle Born Batteries | battlebornbatteries.com
- Terms & Conditions | Battle Born Batteries | battlebornbatteries.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>