BOSS JB-2 Angry Driver Owner’s Manual

June 12, 2024
Boss

BOSS Logo JB-2 Angry Driver
Owner’s Manual

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.

Main Features

The JB-2 is a distortion pedal cooperatively developed by JHS PEDALS and BOSS.

  • It is equipped with two completely independent distortion effects designed respectively by JHS PEDALS and BOSS.
  • By switching modes, you can use the JHS PEDALS and BOSS sounds individually, or use them together in series (with your choice of connection order) or parallel to create a wide variety of rock sounds.
  • If you connect a footswitch to the REMOTE jack, you can use it in conjunction with the pedal switch for additional options, such as switching between distortions or turning the effect on/off.

Panel Descriptions

BOSS JB 2 Angry Driver - Overview

IMPORTANT NOTES

  • Some settings might cause the JB-2 to oscillate or might result in increased noise, but this is not a malfunction.

  • To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections.

  • Once everything is properly connected, be sure to follow the procedure below to turn on their power. If you turn on equipment in the wrong order, you risk causing malfunction or equipment failure.
    When powering up: Turn on the power to your guitar amp last.
    When powering down: Turn off the power to your guitar amp first.

  • Before turning the unit on/off, always be sure to turn the volume down. Even with the volume turned down, you might hear some sound when switching the unit on/off. However, this is normal and does not indicate a malfunction.

  • If operating this unit on batteries, please use alkaline or carbon battery.

  • When operating on battery power only, the unit’s indicator will become dim when battery power gets too low. Replace the battery as soon as possible.

  • If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

Changing the Battery

  1. Hold down the pedal and loosen the thumbscrew, then open the pedal upward.
  • The pedal can be opened without detaching the thumbscrew completely.BOSS JB 2 Angry Driver - Description 2. Remove the old battery from the battery housing, and remove the snap cord connected to it. 3. Connect the snap cord to the new battery, and place the battery inside the battery housing.
  • Be sure to carefully observe the battery’s polarity (+ versus -). 4. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal.
  • Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing. 5. Finally, insert the thumbscrew into the guide bush hole and fasten it securely.

MODE List

Use the MODE knob to select the effect you want.

MODE Explanation
JHS A high-gain distortion with a design based on the “Angry Charlie” made by

JHS PEDALS.
It’s a classic sound with a distinctively rich low-frequency range and thick Mids.
BOSS| An overdrive with a design based on the BOSS “BD-2” Blues Driver.
It’s noted for a broad range of expression that responds to your guitar volume and picking dynamics. With a broad range of gain variation, you can create a wide variety of sounds from crunch to hard rock.
JHS/BOSS| Switch between the “JHS” and “BOSS” effects.
J B (1)| Series connection in the order of “JHS” 0 “BOSS.”
B J (
1)| Series connection in the order of “BOSS” 0 “JHS.”
PARALLEL (*1)| “JHS” and “BOSS” circuits connected in parallel.

(*1) Both JHS PEDALS and BOSS are on.

Operation at a Glance

This table shows the operations of the pedal switch and of a footswitch connected to the REMOTE jack.

MODE Pedal switch Footswitch
JHS Effect ON/OFF Switch between JHS/BOSS

BOSS
JHS/BOSS| Switch between JHS/BOSS| Effect ON/OFF
J A B| Effect ON/OFF| JHS ON/OFF
B A J| BOSS ON/OFF
PARALLEL

Intellectual Property Right

  • Roland, BOSS, BLUES DRIVER are either registered trademarks or trademarks of Roland Corporation in the United States and/or other countries.

CMSIS-RTOS RTX Version 4.70.1
Copyright (c) 1999-2009 KEIL, 2009-2015 ARM Germany GmbH All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

  • Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  • Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
  • Neither the name of ARM nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

Main Specifications

Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output Level -20 dBu
Output Impedance 1 kΩ
Recommended Load Impedance 10 kΩ or greater
Power Supply Alkaline battery (9 V, 6LR61) or

Carbon-zinc battery (9 V, 6F22)
AC adaptor (sold separately)
Current Draw| 55 mA
Expected battery life under continuous use: Alkaline: Approx. 7 hours
Carbon: Approx. 2.5 hours
These figures will vary depending on the actual conditions of use.
Dimensions| 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight| 445 g / 1 lb (including battery)
Accessories| Leaflet (“USING THE UNIT SAFELY,”
“IMPORTANT NOTES,” and “Information”)
Alkaline battery (9V, 6LR61)
Options (sold separately)| AC adaptor (PSA-series) Footswitch: FS-5L, FS-6, FS-7
The FS-6 and FS-7 can be used only in latch mode.

  • 0 dBu = 0.775 Vrms
  • This document explains the specifications of the product at the time that the document was issued. For the latest information, refer to the Roland website.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

BOSS Logo © 2017 Roland Corporation

Documents / Resources

| BOSS JB-2 Angry Driver [pdf] Owner's Manual
JB-2 Angry Driver, JB-2, Angry Driver, Driver
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals