TUBBUTEC KAC TM62100 Yamaha SK50D Installation Guide

June 12, 2024
Tubbutec

TUBBUTEC KAC TM62100 Yamaha SK50D Installation Guide
TUBBUTEC KAC TM62100 Yamaha SK50D

Tools you will need:

  • Soldering iron
  • Metal drill 3.2mm (or similar)
  • Metal drill for a 15mm hole (stepping drill for example)
  • Center punch
  • Screw driver

Included in the kit:

  • TM62100 KAC Chip
  • 40pin IC socket
  • Connection cable assemblies
  • 100K resistor for cutoff control
  • 82K resistor and 100nF capacitor for aftertouch control
  • Midi socket drill guide
  • 4x M3 bolt, 4xM3 nut for midi sockets
  • Sticker for midi socket labelling

Principle of operation

The Tubbutec KAC replaces the key assigner chip of the Yamaha SK50D (YM62100).
This enables the user to play the SK50D via MIDI. It also adds filter, resonance, aftertouch, portamento and sustain control via MIDI, and MIDI Out. Further information can be found in the user manual.

The original behaviour is fully maintained

Considerations before assembly

You need to remove the main board from the synthesizer. It is also required to desolder the original Yamaha key assigner chip (YM62100, labelled YM621 F) from the main board. This needs to be done with care not to damage the original chip and/or traces on the board.

Proper tools are required to do this and some basic skills in desoldering.

If you feel uncomfortable to perform this task you might consider reaching out for a technician in your area, or you can contact us.
A list of synth techs can be fund here: https://tubbutec.de/synth-techs/

Two holes for the MIDI jacks need to be drilled in the back panel of the synthesizer.

Desoldering the YM62100 chip

First you need to remove the mainboard from the synthesizer.
To do so carefully unplug all wire assemblies. The picture below can be used for reference to plug the connectors back in the right positions later. Be careful not to damage any of the plastic spacers holding the board.
Desoldering

Use a desoldering pump to desolder IC1, the YM62100 chip. As this is a single layer board without plated-through holes this is relatively easy to do, but take care not to apply too much heat and pressure to the solder pads, as this can easily damage the pads and/or the chip.

After you have removed the Yamaha chip put it in antistatic foam included in the kit to protect it.

Make sure all solder is removed from the solder pads, and that the pads and traces are all intact.
Next step is soldering the 40pin IC socket in place, make sure the notch of the socket reflects the pin 1 location of the original chip.
Install the Tubbutec KAC chip.
Reinstall the mainboard in the synthesizer.
Reconnect the wire assemblies, take care to plug them into the correct sockets.

Mainboard with original KAC
Desoldering

Mainboard with socket
Desoldering

Mainboard with TM62100
Desoldering
Desoldering

Soldering the Cutoff and Resonance wires

Plug the 2pin connector with the long wires in the socket labelled CV on the KAC board.

Route the wires to the upper right corner of the control panel pcb.

Solder the 100K resistor in place where shown in the picture.

Solder the red wire (Resonance control) to the spot shown.

Solder the black wire (Cutoff control) to the spot shown.
Soldering the Cutoff and Resonance wires

Secure the wires with cable ties to the wire loom.

Soldering the sustain and portamento wires

Plug the 3pin connector in the socket labelled CTRL on the KAC board.

Route the black and yellow wire to the jack board.

The yellow wire (sustain) gets soldered directly to the tip of the sustain jack, see picture.

The black wire (portamento) gets soldered directly to the tip of the portamento jack, see picture.
Secure the wires with cable ties to the wire loom

Soldering the aftertouch wire

To solder the aftertouch wire you need to remove the top pcb of the pcb stack right of the mainboard.
Soldering the aftertouch wire

Route the red wire from the CTRL socket to the bottom pcb of the pcb stack. Solder the 82K resistor and the 100nF capacitor in place where shown in the picture.
Solder the red wire to the spot shown.
Soldering the aftertouch wire

Installing the MIDI sockets

First place the drill aid for the MIDI sockets on the back of the synthesizer.

We chose the space between the voltage selector and the Yamaha logo.

There is enough space but it is advisable to take exact measurements where to place the jacks.

After you placed the drill aid use a center punch to mark and drill the holes, 3,2 – 3,5mm for the mounting holes, 15mm for the jacks.

Next step is installing the MIDI jacks. The upper jack is MIDI In (2pin wire assembly), the lower MIDI Out (3pin wire assembly).
Installing the MIDI sockets

As the MIDI jack assemblies are detachable it is also possible to mount the jacks from the outside. In this case it is advisable to drill a 16mm hole.
Installing the MIDI sockets

You can now use the sticker included in the kit to label the midi sockets.
The sticker is transparent in order to blend with the existing print.

That’s all. Have fun.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals