nordlux UKES Heka Black Outdoor Wall Light Instruction Manual
- June 11, 2024
- nordlux
Table of Contents
Instruction Manual
UKES Heka Black Outdoor Wall Light
HEKA VÆG E27
Mounting instruction
IP5X – IP5X: Dust is prevented from entering the lamp in amounts that can
cause damage to the function/safety of the lamp.
IPX4 – IPX4: Raindrops falling from any angle will not affect the
function/safety of the lamp.
– Class I: lamp has an earth terminal and must be connected to the
yellow/green earth wire.
– The lamp is only suitable for connecting directly to the mains.
MAX 60W – Do not exceed the maximum wattage.
– IMPORTANT! Always shut off power to the circuit before starting
installation work. In some countries electrical installation work may only be
carried out by a authorized electrical contractor. Contact your local
electricity authority for advice.
– Disposal of waste equipment by users in private households in the European .
symbol indicates that this product must not be disposed of with your other
household waste. Electrical and electronic equipment contain substances which
may cause damage
to human health and environment if not recycled correctly. It is your
responsibility to hand over to a designated collection point for recycling of
waste electrical and electronic equipment. When handing over for correct
recycling you help to prevent these products straining nature and environment
unnecessarily and to protect human health. For more information regarding
correct disposal please contact your local city purchased this product.
– The mounting instruction must not be discarded.
Parallel arranging possible.
We congratulate you on your new outdoor lamp!
Stainless steel
Remember to take care of your lamp. Just follow the guidelines below.
The shiny, uniform and decorative surface of stainless steel makes it very
suitable for outdoor use.
It is an alloy consisting of iron, chrome and nickel. During bath pickling, a
thin, rustproof oxide layer forms on the surface.
The surface is continually vulnerable to atmospheric conditions, and from
other effects of the close environment. This means that the lamp must be
regularly maintained if its surface is to remain shiny and untar-nished by
rust.
Before setting it up, treat your tamp with acid-free oil, and dry it off with
a soft cloth. Repeat this three or four times a year.
Stainless steel lamps are not recommended for use in aggressive environments
such as coastal, agricultural or industrial areas.
Copper, Brass and Tombac fixtures
Our copper, brass and tombac fixtures are made from respectively solid
copper, brass and tombac. The mechanical machining will leave small scratches
in the surface, as well as residues of rinse aid. This rapidly disappears in
the patina process. After the first rain showers the copper / brass / tombak
surface will appear stained, but the aerated air and moisture will soon make
the lamp appear with dark brownish color. Over the years, the material copper
will get a beautiful patina-green color and brass / tombac will get a darker
and more uniform color. The uniformity of the patina surface, as well as the
rate at which the process occurs is dependent on the environment that affect
the fixture.
Hot-galvanized lamps
The zinc treatment of the steet tamps is executed manually in plants.
The temperature of the melted zinc is about 460 degrees. When the famps are
dipped in meited zinc a reaction between the metalls occurs, which develops
alloys in the surface.
The jamp and the components of the lamp are manually dipped in the hot zinc.
This treatment leaves variations in the coating in the form of partly an
uneven surface and partly minor formations of drops.
Thin »zinc curtains« might also occur on the surface and they show as a thin
film which hangs down from the edge of the lamp. This film can easily be
removed or brushed off with a soft brush.
Condensation
Condensation is a natural phenomenon arising under specific atmos- pheric
conditions. Damp heat and cold air meet, which causes conden-sation of water
on the surface.
When water heats up it leads to rising water vapour, which will be able to
affect electric components.
Condensation is not included by Nordiux warranty, unless it is possible to
prove that a technical ‘production error in the lighting causes entry of
water.
In case of condensation please check:
- If the lighting is mounted according to instructions. Washers should seat tightly. Make sure to tension screws and lenses.
- In garden lightings rising damp from the ground may cause condensa- tion in the metal post. This problem can be defeated by filling sealing material into the metal post.
Aluminium fixtures
Our aluminium light fixtures are made from die-cast and/or extruded aluminium,
where the light fixture’s design determines whether both types of materials,
or just one of them, are used for different parts of the same light fixture.
Aluminium light fixtures in raw aluminium are subsequently coated with a
special clear coat, which seals the surface to safeguard against corrosion.
Painted aluminium light fixtures are powder-coated and have a uniform and
smooth surface. To avoid the light fixture tarnishing, it is recommended to
clean and wipe the light fixture after mounting, and repeat this process 3-4
times each year. This is done with a regular cleaning agent. Black light
fixtures which are bleached by strong sunlight can also benefit from treatment
with silicone spray as needed, to maintain the black color. Mounting light
fixtures in coastal, agricultural or industrial areas is not recommended, as
these aggressive surroundings may cause the light fixture to corrode, which
May entail spalling, bubbles in the surface and a whitish incrustation on the
light fixture’s surface.
-It is highly important that drainage holes are kept free of impurities if any.
BEFORE ASSEMBLING THE BOLLARD AGAIN DO REMEMBER TO WIPE OFF ALL PARTS!
In Denmark, outdoor lightings must be mounted by an authorized electrician.
www.nordiux.com
Nordlux A/S – Ø stre Havnegade
34 – DK-9000 Aalborg
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>