ANKER Solix PS400 Portable Solar Panel User Manual

ANKER Solix PS400 Portable Solar Panel User Manual

Using Your Product

1. Unfold Anker SOLIX PS400 Portable Solar Panel and its stand. For maximum charge, adjust the solar panel up to 3 angles and align it directly under the sun.
   
   

2. Charge your portable power station with the included MC4 to XT-60 solar charging cable.
   

Note

1. Anker SOLIX PS400 Portable Solar Panel cannot store electricity. You will need a portable power station to store power.
2. Charging efficiency is subject to sunlight intensity.
3. Keep your portable power station away from direct sunlight. Excessive heat may cause damage.
4. 400W refers to the power of the solar panel, which is not equal to the actual power of the output ports. There will be some power loss when solar energy is transferred into electrical energy, so the actual power of the output ports will be less than the power of the solar panel.

Specifications

Important Safety Instructions

• Avoid dropping.
• Do not disassemble.
• For the safest and fastest charge, use original or certified cables.
• Open flame sources, such as candles, must not be placed on this product.
• Only use a dry cloth or brush to clean this product.

Waste Electrical and Electronic Equipment (WEEE)

 This symbol (with or without a solid bar) means that, according to local laws and regulations, your product and/or its battery should be disposed of separately from household waste. When this product reaches the end of its life, the user has the option of handing it over to a competent recycling organization. Proper recycling of your product will protect human health and the environment.
Manufacture: Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, HongKong

Notice

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio / TV technician for help.

The following importer is the responsible party.
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1-800-988-7973

IC Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

The device is compliance with RF field strength limits, users can obtain Canadian information on RF exposure and compliance.

This Class B digital apparatus complies with Canadian ICES-003.

CAN ICES-003 (B)/NMB-003(B)

Declaration of Conformity
Hereby, Anker Innovations Limited declares that this product is in compliance with Directives 2014/35/EU & 2014/30/EU & 2011/65/ EU. The full text of the EU Declaration of Conformity is available at the following internet address: https://www.anker.com.
The following importer is the responsible party (contract for EU matters) Anker Innovations Deutschland GmbH Georg-Muche-Strasse 3, 80807 Munich, Germany

GB Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A2433 is in compliance with Electrical Equipment (Safety) Regulations 2016 & Electromagnetic Compatibility Regulations 2016 & The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The full text of the GB declaration of conformity is available at the following internet address: https://www.anker.com.
The following importer is the responsible party (contract for UK matters) Anker Technology (UK) Limited, GNR8, 49 Clarendon Road, Watford, Hertfordshire, WD17 1HP, United Kingdom

References

• Anker Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>