Sony SRS-XB23 Wireless Bluetooth Portable Speaker Reference Guide

Sony SRS-XB23 Wireless Bluetooth Portable Speaker

Before operating the unit, please read this guide thoroughly and retain it for future reference. Please access the following URL and read the contents of the END USER LICENSE AGREEMENT. https://rd1.sony.net/help/speaker/el20/huc/

Owner’s Record
The serial number is located inside the cap on the rear side of the product. Record the serial number in the space provided below. Refer to them whenever you call your Sony dealer regarding this product.

CAUTION

• Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
• Do not expose the batteries (battery pack or batteries installed) to excessive heat such as sunshine, fire, or the like for a long time.
• Do not expose the batteries to extreme low-temperature conditions that may result in overheating and thermal runaway.
• Do not dismantle, open or shred secondary cells or batteries. In the event of a cell leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice. Secondary cells and batteries need to be charged before use.
• Always use the correct charger and refer to the manufacturer’s instructions or equipment manual for proper charging instructions. After extended periods of storage, it may be necessary to charge and discharge the cells or batteries several times to obtain maximum performance. Dispose of it properly.

RECYCLING RECHARGEABLE BATTERIES

Rechargeable batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you.
For more information regarding recycling of rechargeable batteries, visit https://www.sony.com/electronics/eco/environmental-management
Caution: Do not handle damaged or leaking rechargeable batteries.

Do not place this product close to medical devices
This product (including accessories) has a magnet(s) that may interfere with pacemakers, programmable shunt valves for hydrocephalus treatment, or other medical devices. Do not place this product close to persons who use such medical devices. Consult your doctor before using this product if you use any such medical device.

For customers in the USA
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter.

If you have any questions about this product:

• Visit: https://www.sony.com/electronics/support
• Contact: Sony Customer Information Service Center at 1-800-222-7669
• Write: Sony Customer Information Service Center 12451 Gateway Blvd., Fort Myers, FL 33913
• Trade Name: SONY
• Model: SRS-XB23
• Responsible Party: Sony Electronics Inc.
• Address: 16535 Via Esprillo, San Diego, CA 92127 U.S.A.
• Telephone Number: 858-942-2230

This device complies with part 15 of FCC Rules and Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.
3. This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm (7 7/8 in) or more away from the person’s body.

Caution on charging

Inserting the USB plug while it is wet may cause a short circuit due to foreign matter or liquid (tap water, salt water, soft drinks, etc.) getting on the main unit or charging cable. This may cause malfunctions or abnormal overheating.

• Never insert the USB plug while the main unit or charging cable is wet.

Precautions

On Safety

• If your skin touches this product for a long time when the power is on, it may cause a low-temperature injury.
• Important information such as the model name is located on the inner and outer surfaces of the cap on the rear side of the unit.

On placement

• To eliminate the risk of malfunctions, avoid the following locations when placing or leaving this unit.
  • A place subject to high temperatures, such as under direct sunlight or lighting equipment, near a heat source, or in a sauna
  • Inside a vehicle with the windows closed (especially in the summertime)
  • A place subject to excessive dust
  • A place subject to strong vibration
• Place this unit on a flat, level surface. When placed on a sloped surface, the unit may fall over or fall off the surface due to its own vibration, resulting in injuries, malfunctions, or performance degradation.
• Depending on the conditions where this unit is placed, it may fall over or fall off the surface. Do not leave any valuables near the unit.
• This unit is not anti-magnetic. Keep objects susceptible to magnetism (recorded tapes, watches, cash cards, and credit cards with magnetic coding, etc.) away from the unit. When you carry around the unit, keep this in mind as well.

Others

• Do not use or leave the unit in an extremely cold or hot environment (temperature outside the range of 5 °C – 35 °C (41 °F – 95 °F)). If the unit is used or left in outside the above range, the unit may automatically stop to protect internal circuitry.
• At high temperatures, the charging may stop or the volume may reduce to protect the battery.
• Even if you do not intend to use the unit for a long time, charge the battery to its full capacity once every 6 months to maintain its performance.

About the Voice Guidance

IMPORTANT: THE SOUND GUIDANCE IS AVAILABLE IN THIS PRODUCT ONLY IN ENGLISH
Depending on the status of the unit, the voice guidance outputs from the unit as followings.

• When entering pairing mode: “BLUETOOTH pairing”
• When establishing a BLUETOOTH connection: “BLUETOOTH connected”
• When disconnecting a BLUETOOTH connection: “BLUETOOTH disconnected”
• When pressing the BATT (battery) button to check the battery power during the unit is turned on: “Battery fully charged/Battery about 70%/Battery about 50%/Battery about 30%/Please charge”
• When pressing and holding the ST PAIR button during the Stereo Pair function: “Left/Right”

On Copyrights

• Android, Google Play, and other related marks and logos are trademarks of Google LLC.
• LDAC™ is a trademark of Sony Corporation.
• The BLUETOOTH® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license.
• Apple, the Apple logo, iPhone, iPod, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
• Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
• USB Type-C® and USB-C® are trademarks of USB Implementers Forum.
• Other trademarks and trade names are those of their respective owners.
• ™ and ® marks are omitted in the documents.

Notes on waterproof and dustproof features (Read before using the unit)

The waterproof and dustproof performance of the unit, with the cap fastened securely, has a waterproof specification of IPX71 as specified in “Degree of protection against water immersion” of the IEC60529 “Ingress Protection Rating (IP Code)”3, and a dust-proof specification of IP6X2 as specified in “Degrees of protection against solid foreign objects”3.

Liquids that the waterproof performance specifications apply to

• Applicable: freshwater, tap water, pool water, salt water
• Not applicable: liquids other than the above (soapy water, water with detergent or bath agents, shampoo, hot spring water, etc.)

1. IPX7 (Degree of protection against water immersion): For details, refer to the Help Guide.
2. IP6X (Degrees of protection against dust): For details, refer to the Help Guide.
3. The supplied accessories and the connectors of this unit (USB) are neither waterproof nor dustproof. To reduce the risk of fire or electric shocks, do not expose the unit to water or droplets while using either or both of connectors (USB). Do not place a vase or any other liquid-filled container on the unit. The connectors (USB). Do not place a vase or any other liquid-filled container on the unit.

The waterproof and dust-proof performance of the unit is based on our measurements under the conditions herein described. Note that malfunctions as a result of water immersion or dust intrusion caused by misuse by the customer are not covered by the warranty.

To avoid deterioration of waterproof and dustproof performance Check the following and use the unit correctly.

• The unit passes the drop test from 1.22 m (4 ft) on plywood of 5 cm (2 in) thickness conforming to MIL-STD810H Method 516.8-Shock. However, this does not guarantee any damage, no breakdown, or waterproof and dustproof performance in all conditions. Deformation or damage from dropping the unit or subjecting it to mechanical shock may cause deterioration of the waterproof and dustproof performance.
• This unit does not have a design that is resistant to water pressure. Use of the unit in a location where high water pressure is applied, such as in the shower, may cause a malfunction.
• Do not pour high-temperature water or blow hot air from a hair dryer or any other appliance on the unit directly. Also never use the unit in a place subject to high temperatures, such as in a sauna or near a heat source.
• Handle the cap with care. The cap plays a very important role in the maintenance of the waterproof and dustproof performance. When using the unit, make sure that the cap is closed completely. When closing the cap, be careful not to allow foreign objects inside. If the cap is not closed completely the waterproof and dustproof performance may deteriorate and may cause a malfunction of the unit as a result of water or dust particles entering the unit.

How to care for the unit

Although the fabric part of the unit has water-repellent treatment applied, you can use the unit more comfortably and for a longer period of time by following the maintenance procedure below.

• If the surface of the unit gets dirty in the following cases, wash the unit with fresh water (tap water, etc.) promptly to remove the dirt. Leaving dirt on its surface may cause the fabric part or the passive radiator section to discolor or deteriorate, or the unit to malfunction. Ex.
  • When salt, sand, etc. is stuck on the unit after using it on a beach, poolside, etc.
  • When the unit is stained with foreign substances (sunscreen, suntan oil, etc.)
• If the unit gets wet, wipe off the moisture using a dry soft cloth immediately. In addition, dry the unit in an airy place until no moisture remains.
• The sound quality may change when water enters the speaker or passive radiator section of the unit. It is not a malfunction. Wipe off the moisture on its surface, and put the unit on a dry soft cloth to drain the collected water inside the unit. Then, dry the unit in an airy place until no moisture remains.

Note

• If the surface of the unit gets dirty, do not use detergent, thinner, benzine, alcohol, etc. to clean the unit because it will affect the water-repellent function of the fabric part of the unit.
• Especially in cold regions, be sure to wipe off the moisture after using the unit. Leaving moisture on its surface may cause the unit to freeze and malfunction.
• If sand grains, etc. enter the fabric or other parts of the unit, remove them carefully. Never use a vacuum cleaner, etc. on the unit. It may cause damage of the speaker section or other parts of the unit.

Notes on the License

This product contains software that Sony uses under a licensing agreement with the owner of its copyright. We are obligated to announce the contents of the agreement to customers under requirement by the owner of the copyright for the software. Please access the following URL and read the contents of the license. https://rd1.sony.net/help/speaker/sl/20/

Notice on GNU GPL/LGPL applied software
This product contains software that is subject to the following GNU General Public License (hereinafter referred to as “GPL”) or GNU Lesser General Public License (hereinafter referred to as “LGPL”). These establish that customers have the right to acquire, modify, and redistribute the source code of said software in accordance with the terms of the GPL or LGPL supplied. The source code for the above-listed software is available on the Web. To download, please access the following URL then select the model name “SRS-XB23”.

URL: http://oss.sony.net/Products/Linux/
Please note that Sony cannot answer or respond to any inquiries regarding the content of the source code.

Specifications

Speaker section

• Full range unit Approx. 42 mm × 51 mm (1 11/16 in × 2 1/8 in) (2)
• Enclosure type Passive radiator model

BLUETOOTH

• Communication System BLUETOOTH Specification version 5.0
• Maximum communication range Line of sight approx. 30 m (98 ft)*1
• Frequency band 2.4 GHz band (2.4000 GHz – 2.4835 GHz)
• Modulation method FHSS
• *Compatible BLUETOOTH Profiles2**
  • A2DP (Advanced Audio Distribution Profile)
  • AVRCP (Audio Video Remote Control Profile)
  • HSP (Headset Profile)
  • HFP (Hands-free Profile)
• *Supported Codec3** SBC (Subband Codec); AAC (Advanced Audio Coding); LDAC
• Transmission range (A2DP) 20 Hz – 20,000 Hz (Sampling frequency 44.1 kHz)

1. The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, reception sensitivity, antenna performance, operating system, software application, etc.
2. BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communications between devices.
3. Codec: Audio signal compression and conversion format

Note
Depending on the network environment, there may be an interruption at the high bitrate transmission.

Microphone

• Type Electret condenser
• Directional characteristic Omni directional
• Effective frequency range 100 Hz – 7,000 Hz

Amplifier section

• POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 4 ohms loads, both channels are driven, from 100 Hz – 10,000 Hz; rated 4 watts per channel minimum RMS power at stereo mode, with no more than 1% total harmonic distortion from 250 milliwatts to rated output.

General

• Power DC 5 V (using a commercially-available USB AC adaptor capable of feeding in 1.5 A) or, using a built-in lithium-ion battery
• Lithium-ion battery life (with playback via a BLUETOOTH connection)
  • Approx. 12 hours4 7
  • Approx. 10 hours5 7
  • Approx. 3 hours6 7
• Dimensions (including projecting parts and controls) Approx. 76 mm (3 in) dia. × 218 mm (8 5/8 in) (H)
• Mass Approx. 580 g (1 lb 5 oz) including battery
• Supplied accessory USB Type-C® cable (USB-A to USB-C® / Max. 1.5 A) (1) Strap (1) (attached to the unit)

1. Measured value acquired by playing our specified music source with the volume level of the unit set to 34, and the sound mode set to STAMINA.
2. Measured value acquired by playing our specified music source with the volume level of the unit set to 31 and with the factory default settings (sound mode: EXTRA BASS).
3. Measured value acquired by playing our specified music source with the volume level of the unit set to maximum and with the factory default settings (sound mode: EXTRA BASS).
4. Actual performance time may vary from the listed time due to the volume, songs played, the surrounding temperature, and usage conditions.

System requirements for charging the battery using USB
Using a commercially-available USB AC adaptor capable of feeding in 1.5 A

Compatible iPhone/iPod models
iPhone XS Max, iPhone XS, iPhone XR, iPhone X, iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone 7, iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6, iPhone 5s, iPod touch (6th generation)
The unit is compatible with iOS 10.0 or later. Design and specifications are subject to change without notice.

FAQ’s

Is the Sony SRS-XB23 a wireless speaker?

Yes, the Sony SRS-XB23 is a wireless Bluetooth portable speaker that allows you to connect and stream audio wirelessly from your compatible devices.

What is the battery life of the SRS-XB23?

The Sony SRS-XB23 offers up to 12 hours of battery life, ensuring extended playback time without needing to recharge.

Is the SRS-XB23 waterproof or water-resistant?

The Sony SRS-XB23 is water-resistant with an IP67 rating, making it capable of withstanding water splashes, rain, and even submersion in water for a short period.

Can I pair multiple SRS-XB23 speakers together?

Yes, using the Party Connect feature, you can wirelessly connect and sync multiple SRS-XB23 speakers to create a more immersive and stereo sound experience.

Does the SRS-XB23 have a built-in microphone for hands-free calls?

Yes, the Sony SRS-XB23 features a built-in microphone, allowing you to make and receive hands-free phone calls directly through the speaker.

Can I control the speaker using voice commands?

The Sony SRS-XB23 does not have built-in voice control. However, you can connect it to your smartphone or other voice-enabled devices to control playback using voice commands.

Does the speaker have an auxiliary input for wired connections?

Yes, the Sony SRS-XB23 includes a 3.5mm auxiliary input, allowing you to connect non-Bluetooth devices using a standard audio cable.

Is the SRS-XB23 compatible with NFC (Near Field Communication)?

Yes, the Sony SRS-XB23 supports NFC technology, enabling quick and easy pairing with NFC-enabled devices.

Can I charge my smartphone using the SRS-XB23 speaker?

No, the Sony SRS-XB23 does not have a built-in power bank feature to charge external devices.

Does the speaker come with a carrying strap or handle?

Yes, the Sony SRS-XB23 is designed with a detachable carrying strap that makes it convenient to carry or hang the speaker wherever you go.

Can I adjust the bass and sound settings on the SRS-XB23?

Yes, the Sony SRS-XB23 offers extra bass functionality and allows you to customize the sound using the Sony | Music Center app available for smartphones.

Does the speaker come with a warranty?

Yes, the Sony SRS-XB23 wireless Bluetooth portable speaker typically comes with a manufacturer's warranty. Please check the specific warranty details provided by Sony or contact their customer support for more information.

Download This PDF Link:Sony SRS-XB23 Wireless Speaker – Device.report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>